DOWNLOAD Panasonic DMC-G10KPP / DMC-G10KEB / DMC-G10KEC / DMC-G10KEG / DMC-G10KGC / DMC-G10KGD / DMC-G10KGH / DMC-G10KGT / DMC-G10KGK / DMC-G10KGN / DMC-G10WGC / DMC-G10WGH / DMC-G10WGN Service Manual ↓ Size: 8.35 MB | Pages: 68 in PDF or view online for FREE

ORDER NO. DSC1005030CE

B26

Vol.1

Colour
(K)...........Black Type

2

PAGE

PAGE

1 Safety Precautions -----------------------------------------------3

1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
1.4. How to Discharge the E. Capacitor on POW

Flash P.C.B. -------------------------------------------------4

2 Warning --------------------------------------------------------------5

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices ----------5

2.2. How to Recycle the Lithium Ion Battery (U.S.

Only)-----------------------------------------------------------5

2.3. Caution for AC Cord (For EB/GC/GH) ----------------6
2.4. How to Replace the Lithium Battery -------------------7

3 Service Navigation------------------------------------------------8

3.1. Introduction --------------------------------------------------8
3.2. Important Notice --------------------------------------------8
3.3. General Description About Lead Free Solder

(PbF) -------------------------------------------------------- 12

3.4. How to Define the Model Suffix (NTSC or PAL

model)------------------------------------------------------- 13

4 Specifications ---------------------------------------------------- 16
5 Location of Controls and Components ------------------ 17
6 Service Mode ----------------------------------------------------- 21

6.1. Error Code Memory Function ------------------------- 21

7 Troubleshooting Guide---------------------------------------- 23

7.1. Checking Method of Body and

Interchangeable Lens ----------------------------------- 23

8 Service Fixture & Tools --------------------------------------- 28

8.1. Service Fixture and Tools ------------------------------ 28
8.2. Clean Box -------------------------------------------------- 29
8.3. Service Position ------------------------------------------ 30

9 Disassembly and Assembly Instructions --------------- 32

9.1. Camera Body Part --------------------------------------- 32
9.2. Disassembly and Assemble Procedure for the

Lens (H-FS014042)-------------------------------------- 41

9.3. Disassembly and Assemble Procedure for the

Lens (H-FS045200)-------------------------------------- 42

10 Measurements and Adjustments -------------------------- 43

10.1. Matrix Chart for Replaced Part and Necessary

Adjustment ------------------------------------------------- 43

11 Maintenance ------------------------------------------------------ 45

11.1. Notice in external cleaning----------------------------- 45
11.2. General description (Lens cleaning:

Interchangeable Lens/H-FS014042) ---------------- 46

11.3. eneral description (Lens cleaning:

Interchangeable Lens/H-FS045200) ---------------- 49

3

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment
which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.

2. An Isolation Transformer should always be used during

the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices

such as insulation barriers, insulation papers shields are
properly installed.

5. After servicing, make the following leakage current

checks to prevent the customer from being exposed to
shock hazards.

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M

Ω and 5.2 MΩ. When the exposed

metal does not have a return path to the chassis, the
reading must be infinity.

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5 k

Ω, 10 W resistor, in parallel with a 0.15 μF

capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.

3. Use an AC voltmeter, with 1 k

Ω/V or more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 V RMS.

A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.

Figure. 1

4

1. Be sure to discharge the E. Capacitor on POW FLASH  P.C.B..
2. Be careful of the high voltage circuit on POW FLASH  P.C.B. when servicing.

1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k

Ω /5W).

(An equivalent type of resistor may be used.)

3. Put the resistor between both terminals of E. Capacitor on POW FLASH  P.C.B. for approx. 5 seconds.
4. After discharging confirm that the E. Capacitor voltage is lower than 10V using a voltmeter.

Fig. F1