DOWNLOAD Panasonic WV-NM100 Service Manual ↓ Size: 1.25 MB | Pages: 25 in PDF or view online for FREE

– 6 –

Begin the setup when the PC is in the same condition as just

after the startup.

The "Control Panel" window appears.

Select "Control Panel" ([Start] - [Settings] - [Control Panel]).

Click once to select the [Network] icon.

The "Network" window appears.

The "TCP/IP Properties" window appears.

Click the [Configuration] tab.

Click to select the TCP/IP protocol of the currently used net-
work card.
If the item of the TCP/IP protocol is not displayed, refer to
the operating instructions of the OS and follow the proce-
dures to install the TCP/IP.

Click the [Properties] button.

Click the [IP Address] tab.

Click the "Specify an IP address" radio button.

Enter the IP Address and the Subnet Mask as follows.

• IP Address:

192.168.0.9

• Subnet Mask:

255.255.255.0

Click the [OK] button, and the window closes.

Restart the PC to make the IP Address valid.

The following procedure is an example when using Windows 98 SE.

– 7 –

Note: It will take around 2 minutes until it becomes usable, and the Network Camera can not be oper-

ated in the meantime.
When the power is supplied, the power LED lights up for around 80 seconds and then blinks for
around 20 seconds. Then the camera performs one complete panning and tilting operation.

•

Referring to Fig. 2-3, check the DC Voltage at Pin 5 (V5A) and Pin 7 (V3A) of E2 on the Power Board

• +9V, +5V and +3.3V DC Circuit on the Power Board

have problem.
(

⇒

Refer to    ,     ,     of the SCHEMATIC DIAGRAM 
OF POWER BOARD on page 16.)

• Otherwise, the power line on the Power Board is

shorted to ground possibility.

• +5V DC Circuit on the Power Board has problem.

(

⇒

Refer to    of the SCHEMATIC DIAGRAM OF 
POWER BOARD on page 16.)

• +3.3V DC Circuit on the Power Board has problem.

(

⇒

Refer to     of the SCHEMATIC DIAGRAM OF POWER BOARD on 
page 16.)

• Power Board has no problem.
• Power LED has problem.

⇒

Proceed to next step  Confirmation of the Camera Detection .

E2

(Pin 1)

Power Board

(Pin 10:For Ground)

– 8 –

• Proceed to  Confirmation of the Panning/Tilting Controls .

• Flexible Cable of the Camera Module Ass'y is broken or uncon-

nected from CN500 on the Main Board.

• Otherwise,     of the OVERALL BLOCK DIAGRAM on page 10

has problem.

• Flexible Cables of the Pan/Tilt Mechanical Ass'y are broken.
• Otherwise,       of the OVERALL BLOCK DIAGRAM on page 10 has problem.

Note: • Set TCP/IP address to correctly.

• Do not use proxy for address 192.168.0.10.

IP Address: 

192.168.0.2~9.11~254

Subnet Mask: 

255.255.255.0

Default Gateway:  192.168.0.1

Note: Access from the browser with correct IP Address.

IP Address: 192.168.0.10

•

of the OVERALL BLOCK DIAGRAM on page 10 has problem.

• Connect them correctly and proceed.
•

Confirmation of the Camera Detection again.

• Main Board has problem.

(Except     ,     ,     of the OVERALL BLOCK DIAGRAM on page 10.)

(Click the [REFRESH] button after the "Panasonic IP Setup" software is started.)

• Proceed to  Confirmation of the Panning/Tilting Controls .

TO RS232C

3

1

1

4

TO PAN

1

4

1

3

1

17

1

2

26

27

10

1

10

BAT1
LITHIUM
BATTERY

TO
AC ADAPTER
(PS1)

CAMERA
MODULE
ASS'Y (EU1)

PAN / TILT
MECHANICAL
ASS'Y (M1)

TO TILT

TO

 PLD

TO POWER

TO CAMERA

TO BATTERY

1

14

TO

 JT

AG

– 9 –