Panasonic WV-NM100 Service Manual ▷ View online
ORDER NO. AVS0301471C0
S02
S02
Network Camera
WV-NM100
SPECIFICATIONS
●
Camera
Effective Pixels:
660 (H) x 492 (V)
Lens:
F2.35
Horizontal Angular field of view: 51°
Focal length: 50 cm ~
∞
Minimum Illumination:
10 lx (30 fps, Slow shutter: OFF)
2 lx (Slow shutter: 10 is selected)
Panning range:
140° (–70° - +70°)
Tilting range:
120° (–90° - +30°) when mounted on the w
Pan / Tilt Preset Positions:
8 positions
●
Other Specifications
Power Source:
9V DC, 330mA (using the supplied AC adapter)
Power Source (Supplied AC adapter):
120V AC, 60Hz, 200mA (for NTSC model) ; 230V AC, 50Hz, 200mA (for PAL model)
Ambient Operating Temperature:
0° C - +40° C (32°F - 104°F)
Ambient Operating Humidity:
Less than 90% (no condensation)
Compression Methods:
JPEG or MPEG-4
Resolution:
JPEG:
VGA (640 x 480) / QVGA (320 x 240) / QQVGA (160 x 120)
MPEG-4:
CIF (352 x 288) / QCIF (176 x 144)
Picture Quality:
JPEG:
Super Fine / Fine / Normal / Low
MPEG-4:
Fine / Normal / Low
Picture Display Size:
x1.0 / x1.5 / x2.0 (resolution does not change)
2 0 0 3
M a t s u s h i t a E l e c t r i c I n d u s t r i a l C o . , L t d .
A l l r i g h t s r e s e r v e d . U n a u t h o r i z e d c o p y i n g a n d
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
Y
WARNING
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage within
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that impotant literature concerning
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
T
here are special components used in this equipment which are important for safety. These parts are indicated
by the " " mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent x-radiation, shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.
IMPORTANT SAFETY NOTICE
Interface:
10Base-T / 100Base-TX port (RJ-45) x1
Alarm Input:
OFF:
Open or 4 V DC – 5 V DC
ON:
Make contact with GND
Alarm Output:
Collector output (Internal pull-up)
OFF:
Open or 5V DC or less
ON:
50 mA or less, 1 V DC or less
AUX Output:
Collector output (Internal pull-up)
OFF:
Open or 5V DC or less
ON:
50 mA or less, 1 V DC or less
Weight:
Approx. 180 g (AC adapter excluded)
Dimensions:
95 mm (H) x 93 mm (W) x 61.5 mm (D) (Wall-mounting bracket excluded)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
Specifications are subject to change without notice.
LITHIUM BATTERY
WARNING
The lithium battery in this equipment must only be
replaced by qualified personnel. When necessary,
contact your local Panasonic supplier.
replaced by qualified personnel. When necessary,
contact your local Panasonic supplier.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recom-
mended by the equipment manufacturer. Discard used
batteries according to manufacture's instructions.
Replace only with the same or equivalent type recom-
mended by the equipment manufacturer. Discard used
batteries according to manufacture's instructions.
STANDARD ACCESSORIES
AC Adapter (Part No. N0JBEF000001: for NTSC model
N0JCEF000002 :for U.K
N0JCEF000001 :for outside U.K)
......................................................1 pc.
CD-ROM ........................................................................ 1 pc.
Quick Reference Guide .................................................. 1 pc.
Screws .......................................................................... 2 pcs.
Wall-mounting Bracket ................................................... 1 pc.
CONTENTS
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS............................................................. 1
DISASSEMBLING PROCEDURE.......................................................................................................... 2
LITHIUM BATTERY REPLACEMENT PROCEDURE............................................................................3
TROUBLESHOOTING ............................................................................................................................4
WIRING DIAGRAM ................................................................................................................................ 9
OVERALL BLOCK DIAGRAM..............................................................................................................10
SCHEMATIC DIAGRAM
MAIN BOARD
(1/4) ..................................................................................................................................................11
(2/4) ..................................................................................................................................................12
(3/4) ..................................................................................................................................................13
(4/4) ..................................................................................................................................................14
POWER BOARD ...............................................................................................................................16
CONDUCTOR VIEW
MAIN BOARD ....................................................................................................................................15
POWER BOARD ...............................................................................................................................17
EXPLODED VIEW.................................................................................................................................18
REPLACEMENT PARTS LIST ........................................................................................................... 19
– 1 –
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
3
Front View
Dome cover
Power LED
You can select ON or OFF for
the LED on the “System settings”.
You can select ON or OFF for
the LED on the “System settings”.
3
Rear View
Connector cover
HTML document initialization switch
All HTML documents return to the default settings when the AC adapter is plugged into
an outlet while this switch is pressed and kept pressed for five seconds or more after the
plug is inserted.
Note:
It will take around five minutes to initialize all HTML documents. The power LED blinks
during the initialization. It changes to steady light after the initialization has been
completed.
All HTML documents return to the default settings when the AC adapter is plugged into
an outlet while this switch is pressed and kept pressed for five seconds or more after the
plug is inserted.
Note:
It will take around five minutes to initialize all HTML documents. The power LED blinks
during the initialization. It changes to steady light after the initialization has been
completed.
Setting reset switch
All settings return to the default settings when the AC adapter is plugged into an outlet
while this switch is pressed and kept pressed for five seconds or more after the plug is
inserted.
All settings return to the default settings when the AC adapter is plugged into an outlet
while this switch is pressed and kept pressed for five seconds or more after the plug is
inserted.
Alarm connector
Power plug connector
(Only use the AC adapter supplied)
(Only use the AC adapter supplied)
Ethernet
connector
connector
Link LED
Access LED
Inside of the connector cover