DOWNLOAD Panasonic WV-CW970 / WV-CW974 Service Manual ↓ Size: 7.4 MB | Pages: 69 in PDF or view online for FREE

2-7

REMOTE

OPERATE

PROG

ALARM
RESET

NORMAL

SYSTEM

ALARM OFF

EVR

Left

Switch

Right

Switch

Mode Selection

Switch

Program

Switch

Up

Switch

Down

Switch

Set

Switch

IN

OUT

STD. CAMERA

VP CAMERA

VIDEO

CAMERA

DC12V IN

RS232C

VP/STD Camera Selection Switch

RS232C Connector

8 Referring to Fig. 3-2-2, remove four screws that secure

the Upper Cover and remove the Upper Cover.

Remove four screws.

Upper Cover

8 Set the switch SW3 on the Board to the position as

shown in Fig. 3-2-3.

8 Set the VP/STD.Camera Selection Switch on the Rear

Panel to STD CAMERA position. 

8 Set the Mode Selection Switch on the Front Panel to the

"ALARM OFF" (center) position.

8 Keep pressing the Program Switch for 3 seconds or more

until "Program Menu" is displayed on the monitor screen.

8 Move the cursor to the "Controller Set Up" position by

pressing the Up and Down Switch.

8 Display the "Controller Set Up Menu" on the monitor by

pressing the Set Switch.

8 Move the cursor to the "Set Up Disable" position by

pressing the Up and Down Switch.

8 Change "Disable" to "Enable" by pressing the Set Switch.
8 After completing the above setting, move the cursor to

the Communication position by pressing the Up and
Down Switch.

8 Display the "Communication Menu" on the monitor by

pressing the Set Switch .

8 After confirming the Baud Rate is 9600, finish this menu

by pressing the Program Switch twice.

<Rear>

<F

ront>

Board

SW3

ON

<SW3>

<SW3>

1 2 3 4

Select switch #2 to ON (PAL) position.

#

ON

OFF

1

FIX

2

NTSC

PAL

3

FIX

4

FIX

2-8

8 Peel the RS485 Setting Label which covers switch holes

on top of the camera.

8 Set the DIP switches (SW1, 2) on the Switch Board as

shown in Fig. 3-3-1.

8 Stick the labels as it was.

8 The adjustment should be done after 30 minutes warm-

up.

8 Set the Logarithmic Gray Scale Chart.
8 Incident light of 1 400 lx ± 50 lx on the Logarithmic Gray

Scale Chart.

8 Aim the Camera at the Logarithmic Gray Scale Chart.
8 Set the Camera by the Remote E.V.R. Adjustment Kit so

that the Logarithmic Gray Scale Chart  becoms full pic-
ture on the Underscanned Colour Video Monitor.

8 Adjust the Lens Focus by the Remote E.V.R. Adjustment

Kit to obtain correct focal point.

8 The adjustments should be done with this Standard

Picture, unless otherwise specified.

8 Make a copy of following necessory files to your comput-

er from original floppy disk.

8  The Example given here is for A 2 drive computer, your

procedure might vary slightly depending on the drive
configuration.

8 Confirm that the contents of CONFIG.SYS file on your

computer is DEVICE=ANSI.SYS (Basic).

8 Insert floppy disk containing the E.V.R. Adjustment

Program into your floppy drive (for example,drive:A) and
type A:

8 At the prompt, type CD IBMPC and press ENTER key.
8 Type COPY RADJ2.EXE B: and press ENTER key.
8 Type CD\ and press ENTER key.
8 Type CD SEQ and press ENTER key.
8 Type COPY CW97E.SEQ B: and press ENTER key.
8 Type COPY CW97AF1.SEQ B: and press ENTER key.
8 Type COPY CW97TLT.SEQ B: and press ENTER key.
8 Type COPY CW97PRE.SEQ B: and press ENTER key.
8 Type CD\ and press ENTER key.
8 Type CD EVR and press ENTER key.
8 Type COPY CW97E.EV2 B: and press ENTER key.
8 After completing installation of program, you are ready to

use the E.V.R. Adjustment Program.

RS48

5Se

tting

S TART

ON

1

2

3

4

5

6

7

8

ON

1

2

3

4

SW

1

SW2

Camera top view

RS485 Setting Label

DIP Switches

SW2
4-bit DIP SW
#1 : ON, #2-#4 : OFF

SW1
8-bit DIP SW
#1-#8 : OFF

2-9

8 The Location of Test Points and Adjusting Controls refer

to Wiring Diagram on page 3-1 or 3-2.

8 Insert new floppy disk containing DOS Operating System

and the E.V.R. Adjustment Program into the computer
(IBM PC/AT) and turn on the Power Switch of the com-
puter.

8 When starting an adjustment, at the prompt, type

RADJ2 CW97E and press the ENTER key, an initial
menu page as shown in Fig. 4-1-1 will be displayed.

This saving procedure is recommended to keep the current
adjustment status of the camera.
8 Press the SAVE (F5) key of the computer, and the com-

puter will ask you for the file name.

8 Type  xxxxxxxx.EV2 B40 19FF. Give an appropriate file

name for xxxxxxxx within 8 letters, but do not use
CW97E.

8 Press the ENTER key.

This loading procedure is recommended to return the adjust-
ment status of the camera to the factory default setting or
the setting you saved before.
8 Press the LOAD (F1) key of the computer, and the com-

puter will ask you for the file name.

8 Type CW97E.EV2 or xxxxxxxx.EV2 (xxxxxxxx means a

file name you named before) and press the ENTER key.

PANASONIC REMOTE EVR ADJUSTMENT SYSTEM CCTV PRODUCT: CW970 EEPROM:0

                                            

MENU

                            

Page (1/1)

         

PAL

1. SC FREQUENCY

11.4. 3200K B_PHASE

2. SC FREQUENCY

12.1. 5100K R_GAIN

3.1. LL PHASE1 FOR ACtype (50Hz)

12.2. 5100K B_GAIN

3.2. LL PHASE2 FOR ACtype (50Hz)

12.3. 5100K R_PHASE

4. HI CLIP LEVEL

12.4. 5100K B_PHASE

5. PEDESTAL

13. HIGH LIGHT CHROMA CLIP

6. ALC DC
7.1. VIDEO OUT GAIN (L)
7.2. VIDEO OUT GAIN (H)
8.1. BURST LEVEL R
8.2. BURST LEVEL B
8.3. BURST PHASE R
8.4. BURST PHASE B
9.1. WB 3200K MANU OFFSET R
9.2. WB 3200K MANU OFFSET B
10.1. WB 6500K ATW LIMIT R
10.2. WB 6500K ATW LIMIT B
11.1. 3200K R_GAIN
11.2. 3200K B_GAIN
11.3. 3200K R_PHASE

<CONTENTS>    TD4 17.73447MHz+ – 40Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY

LOAD (F1)          QUIT (F3)             SAVE (F5)

After replacing EEPROM (IC5 on the Main Board) with new
part, load the initial data to EEPROM according to the fol-
lowing procedure.

q Turn the power off of the WV-CW970/WV-CW974.
w Short between TD777 on the Servo Board or TD17 on

the Main Board (refer to Wiring Diagram on page 3-1 or
3-2) and ground.

e Turn the power on the WV-CW970/WV-CW974.
r Make connection according to "3.1. Connection".
t Insert new floppy disk containing DOS operating System

and the E.V.R. Adjustment Program into the computer
(IBM PC/AT) and turn on the Power Switch of the com-
puter.

y At the prompt, type RADJ2 CW97E and press the

ENTER key, then the initial menu page will be displayed.

u Press the LOAD (F1) key of the computer, and the com-

puter will ask you for the file name .

i Type CW97.EV2 and press the ENTER key.
o When finishing the loading, press the QUIT (F3) key.
!0 Press the N key then press the ENTER key.
!1 Type RADJ2 and press the ENTER key.
!2 Type W_E_0 and press the ENTER key. (refer to Fig. 3-

5-1)

!3 Type A5 and press the ENTER key. (refer to Fig. 3-5-1)
!4 Type W_E_01 and press the ENTER key. (refer to Fig. 3-

5-1)

!5 Type 5A and press the ENTER key. (refer to Fig. 3-5-1)

!6 Turn the power off once and on again of the WV-

CW970/WV-CW974.

!7 Remove the short wire from TD777 on the Servo Board

or TD17 on the Main Board.

!8 Reset the Preset data according to "4.4. Preset Data

Reset Procedure".

!9 Adjust the Camera according to "4.1. Camera

Adjustment", "4.2. Back Focus Adjustment" and "4.3.
Tilt Adjustment" if necessary.

< EVR2 >

W_E_0

N 

!2

EEPROM

000 : XX - A5

N 

!3

< EVR2 >

W_E_01

N 

!4

EEPROM

000 : XX - 5A

N 

!5

2-10

790 mV ± 30 mV

8 Press the ENTER key for next adjustment.

8 Confirm the Colour Temperature at 3 200°K.
8 Aim the Camera at the Logarithmic Gray Scale Chart.
8 Connect the terminated Oscilloscope with 75 Ω to the

Video Output Connector.

8 Adjust data with the ARROW keys so that the High clip

level becomes 790 mV ± 30 mv as shown in Fig. 4-1-3.

8 Connect the terminated Oscilloscope with 75 Ω to the

Video Output Connector.

8 Adjust data with the ARROW keys so that the Pedestal

level becomes 50 mV ± 10 mV as shown in Fig. 4-1-4.

8 Press the ENTER key for next adjustment.

50 mV 

± 10 mV

8 Select the item "1. SC FREQUENCY" with the ARROW

key and press the ENTER key.

8 Connect the Frequncy Counter to TD4.
8 Adjust data with the ARROW keys so that the Subcarrier

Frequency becomes 17.73447 MHz ± 40 Hz.

8 Press the ENTER key for next adjustment.

8 Connect the Frequncy Counter to TD4.
8 Adjust data with the ARROW keys so that the Subcarrier

Frequency becomes 17.73447 MHz ± 40 Hz.

8 Press the ENTER key for next adjustment.

8 Connect the CH1 of the Oscilloscope to the Video Output

Connector.

8 Connect the CH2 of the Oscilloscope to the AC Power

Line.

8 Trigger the Oscilloscope at V-rate.
8 Adjust data with the ARROW keys so that the decay point

of V-sync signal gains 2H ± 4H from the zero-cross point
of the AC Power Line Input Waveforms as shown in Fig.
4-1-2.

8 Press the ENTER key for the next adjustment.
8 Adjust data with the ARROW keys so that the decay point

of V-sync signal gains 2H ± 4H from the zero-cross point
of the AC Power Line Input Waveforms as shown in Fig.
4-1-2.

8 Press the ENTER key for the next adjustment.

Zero-Cross Point

AC Line Input
Waveform

Video Output
Signal Waveform

2H ± 4H

–

+

V SYNC