Panasonic WV-CS850B / WV-CS854BE Service Manual ▷ View online
LIST OF CONSUMPTION PARTS
MO1
Pan Motor
REF. NO.
PART NAME
LIFE
MO2
Tilt Motor
MO3
Cooling Fan
* This is working all the time.
Equal to power on time.
* Lens Motor itself is not supplied, but only
supplied as assembly.
M19
Lens (Focus Motor, Zoom Motor)
M6
Slip Ring
8
Those figures are just for a reference under 35 ˚C environmental temperature and not for a guarantee.
It changes depending on the actual environment/operating condition.
8
Part numbers of these consumption parts are described in Replacement Parts List on page 7-1.
2.16 million PRESET actions
2.16 million AUTOPAN revolutions
(19,200 hours as 32 sec per a turn)
2.16 million AUTOPAN revolutions
(19,200 hours as 32 sec per a turn)
50,000 hours
Each 3.7 million actions
10 million PRESET actions
10 million AUTOPAN revolutions
(88,888 hours as 32 sec per a turn)
10 million AUTOPAN revolutions
(88,888 hours as 32 sec per a turn)
– 2-1 –
ADJUSTMENT PROCEDURE
1. Test Equipments Required
8
The following Test Equipments are required for
adjustment of the Combination Camera WV-
CS850B/CS854BE.
8
Oscilloscope
8
Frequency Counter
8
Digital Voltmeter
8
Vectorscope
8
Underscanned Colour Video Monitor
8
12 V DC Power Supply Unit
8
Lux Meter
8
Lighting (275 footcandles (2 750 lx), Colour Temperature
3 200 ˚K)
8
Personal Computer (IBM PC/AT type or equivalent)
8
Standard Straight RS-232C Cable
8
White Chart or White Paper
8
Radiation Chart
8
Colour Temperature Conversion Filters as shown in Table
1-1.
Table 1-1
8
Logarithmic Gray Scale Chart (Part No.: YWV2310RB99).
8
Colour Chip Chart (Part No.: YWV2100RB98).
8
System Controller such as WV-CU151 or WV-CU161.
8
Electric Variable Resistor (E.V.R.) kit (Part No.:
YWV0EA1174AN) as shown in Fig. 1-1.
Fig. 1-1
8
Extension Cable for the Power Board and the Base Unit
(Part No.:V0EA1266AN) as shown in Fig. 1-2.
Fig. 1-2
8
Extension Board Ass'y A - D(Part No.: V0EA1265AN).
Extension Cable A for CN201 of the Main Board and
the Lens as shown in Fig. 1-3.
Fig. 1-3
Extension Cable B for CN4 of the Main Board and CN1
of the Servo Board as shown in Fig. 1-4.
Fig. 1-4
Extension Cable C for CN5 of the Servo Board and the
Pan Motor as shown in Fig. 1-5.
Fig. 1-5
Extension Cable C for CN2 of the Servo Board and the
Tilt Motor as shown in Fig. 1-6.
Fig. 1-6
Extension Cable D for CN1 and CN2 of the
Communication Board and the Base Unit as shown in
Fig. 1-7.
Fig. 1-7
8
CCD Mounting Adjustment Jig (Part No. : V0MA1120AN)
as shown in Fig. 1-8.
Fig. 1-8
Part No. Description
KODAK
80B
change from 3 200 ˚K to 5 100 ˚K
KODAK
80B and 82C change from 3 200 ˚K to 6 500 ˚K
CN201
CN4
CN1
CN5
CN2
CN1
CN2
UP
A
B
C
UP
A
B
C
D
– 2-2 –
E Referring to Fig. 2-1-3, disconnect one connector, and
remove three screws that secure the Lower Diecast, and
remove the Lower Diecast Case.
Fig. 2-1-3
R Referring to Fig. 2-1-4, remove four screws that secure
the Inner Dome Cover and pull up the Inner Dome Cover.
Fig. 2-1-4
T Referring to Fig. 2-1-5, loosen one screw and disconnect
one connector.
Fig. 2-1-5
2. Disassembling Procedure
2.1. Disassembling Procedure for Camera
Head
Q Referring to Fig. 2-1-1, turn the Dome Cover to counter
clockwise direction, and remove the Dome Cover.
Fig. 2-1-1
W Referring to Fig. 2-1-2, remove one screw and turn the
Lower Diecast Case to the counterclockwise direction
and remove the Lower Diecast Case.
Fig. 2-1-2
Dome Cover
Turn to
counterclockwise.
Turn to counter-
clockwise.
clockwise.
Remove one screw.
Lower
Diecast
Case
SW1
SW2
Disconnect one connentor.
Remove three screws.
Lower Diecast
Case
Case
Inner Dome
Cover
Cover
Remove four screws.
Disconnect one
connector.
connector.
Loosen one
screw.
screw.
– 2-3 –
O Referring to Fig. 2-1-9, remove four screws that secure
the Main Board and remove the Main Board and
disconnect one connector.
Fig. 2-1-9
2.2. Slip Ring Replacement Procedure
8
After disassembling the camera according to the "2.1
Disassembling Procedure for the Camera Head" Q -
T, carry out the following procedure.
Q Referring to Fig. 2-2-1, remove five screws and one
connector that secure the Camera Head Unit, and
remove the Camera Head Unit by pulling it up.
Fig. 2-2-1
Y Referring to Fig. 2-1-6, remove two screws that secure
the Lens Cover and remove the Lens Cover .
Fig. 2-1-6
U Referring to Fig. 2-1-7, remove one screw that secure the
Tilt Board.
Fig. 2-1-7
I Referring to Fig. 2-1-8, remove three screws that secure
the Camera Unit and remove the Camera Unit.
Fig. 2-1-8
Remove one screw.
Tilt Board
Remove
two screws.
two screws.
Lens Cover
Remove one connector.
Slip Ring
Remove five screws.
Camera Head Unit
Remove
three screws.
three screws.
Camera Unit
Remove two screws.
Main Board
Remove two screws
Disconnect
one connector.
one connector.
– 2-4 –
Click on the first or last page to see other WV-CS850B / WV-CS854BE service manuals if exist.