Panasonic VL-G201RU-N / VL-G201RU-S Service Manual ▷ View online
5.3. INSTALLING THE MONITOR STATION
1. Install the mounting bracket to a wall using the wood screws (4 mm
×16 mm).
×16 mm).
•
•
•
•
Remove the mounting bracket from the rear of the monitor station
beforehand.
beforehand.
•
•
•
•
Before drilling, see Standard installation position of the door
station and camera range for installation location (P.9).
station and camera range for installation location (P.9).
2. Attach the power cable to the terminal. See To attach the power
cable for details on how to attach the power cable (P.17).
cable for details on how to attach the power cable (P.17).
•
•
•
•
If you want to use your own power cable, see Power cable/wire
type and distance (P.10).
type and distance (P.10).
3. Attach the wires that connect to the door station to the terminal. See
To attach the wires for details on how to attach the wires.
To attach the wires for details on how to attach the wires.
•
•
•
•
See Power cable/wire type and distance for the wire type and
distance.(P.10)
distance.(P.10)
•
•
•
•
See the Wiring schematic diagram (P.10).
13
VL-G201RU-N / VL-G201RU-S
•
•
•
•
If you want to connect the wires and the power cable without them
passing through a hole in the wall, connect by passing the wires
through the wire guide, and the power cable through the power
cable guide.
passing through a hole in the wall, connect by passing the wires
through the wire guide, and the power cable through the power
cable guide.
4. Mount the monitor station to the mounting bracket.
5. Take out the AC adaptor and the DC terminal from the case.
•
•
•
•
Push the arrow mark on the front case, then release from the rear
case.
case.
14
VL-G201RU-N / VL-G201RU-S
6. Connect the power cable to the DC terminal, the power cord to the
AC adaptor, then connect the power cord to the AC outlet (100 V - 240
V, 50 Hz / 60 Hz).
AC adaptor, then connect the power cord to the AC outlet (100 V - 240
V, 50 Hz / 60 Hz).
•
•
•
•
Be sure to connect the power cable to the 2 holes on the left side
of the DC terminal.
of the DC terminal.
5.3.1. To attach the AC adaptor and the DC terminal to a wall
By placing the AC adaptor and the DC terminal in the case and mounting the case to the wall, you can protect the AC adaptor
and the DC terminal from tampering and exposure.
and the DC terminal from tampering and exposure.
1. Attach the rear part of the case to a wall using the wood screws. (4
mm × 16 mm)
mm × 16 mm)
2. Pack the AC adaptor and DC terminal as shown.
1.
1.
Pack the AC adaptor in the rear case.
•
•
•
•
Be sure to run the power cord through the power cord hole.
2.
Pack the DC terminal in the rear case.
•
•
•
•
Be sure to bundle the DC cord so that it will not touch the
bottom of the case.
bottom of the case.
•
•
•
•
Be sure to run the wires through the wire hole, then under the
wire rib.
wire rib.
3. Attach the front of the case.
15
VL-G201RU-N / VL-G201RU-S
•
•
•
•
To open the case again, push the bottom of the front case, then
release from the rear case.
release from the rear case.
16
VL-G201RU-N / VL-G201RU-S
Click on the first or last page to see other VL-G201RU-N / VL-G201RU-S service manuals if exist.