Panasonic SC-HC15EB / SC-HC15EG / SC-HC15EP Service Manual ▷ View online
9
2.4.
Handling Precaution for Traverse Deck
The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the Traverse Deck.
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the Traverse Deck.
2.4.1.
Cautions to Be Taken in Handling the Optical Pickup Unit
The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.
2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed
2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed
should be short-circuited with a short pin or a clip.
3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.
4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexi-
4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexi-
ble cable, cut off the antistatic FPC.
Figure 1
2.4.2.
Grounding for electrostatic breakdown prevention
Some devices such as the CD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electricity
in the working environment. Proceed servicing works under the working environment where grounding works is completed.
in the working environment. Proceed servicing works under the working environment where grounding works is completed.
2.4.2.1.
Worktable grounding
1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet.
2.4.2.2.
Human body grounding
1. Use the anti-static wrist strap to discharge the static electricity form your body (Figure 2).
Figure 2
10
3 Service Navigation
3.1.
Service Information
This service manual contains technical information which will allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
manual.
• Micro-processor:
1) The following components are supplied as an assembled part.
- Micro-processor IC, (IC801) (RFKWMHC25M0)
11
4 Specifications
Q Amplifier Section
RMS Output Power Stereo Mode
Front Ch (both channels driven)
RMS Output Power Stereo Mode
Front Ch (both channels driven)
5 W per channel (6
Ω), 1 kHz,
10 % THD
Total RMS stereo mode power
10 W
Q FM/AM tuner, terminals section
Preset station
Preset station
FM 30 stations
AM 15 stations
Frequency modulation (FM)
Frequency range
Frequency range
87.50 MHz to 108.00 MHz
(50 kHz step)
Antenna terminals
75
Ω (unbalanced)
Amplitude modulation (AM)
Frequency range
Frequency range
522 kHz to 1629 kHz (9 kHz step)
520 kHz to 1630 kHz
(10 kHz step)
Headphone jack
Terminal
Terminal
Stereo, 3.5 mm jack
Aux (rear)
Terminal
Terminal
Stereo, 3.5 mm jack
Q Disc Section
Disc played [8 cm or 12 cm]
CD, CD-R/RW (CD-DA, MP3* formatted disc)
* MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength
Disc played [8 cm or 12 cm]
CD, CD-R/RW (CD-DA, MP3* formatted disc)
* MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength
790 nm (CD)
Laser power
CLASS I (CD)
Audio output (Disc)
Number of channels
Number of channels
2 ch (FL, FR)
FL = Front left channel
FR = Front right channel
Q USB Section
USB port
USB Standard
FR = Front right channel
Q USB Section
USB port
USB Standard
USB 2.0 full speed
Media file format support
MP3 (*.mp3)
USB device file system
FAT 12, FAT 16, FAT 32
USB port power
500 mA (max)
Q Speaker Section
Type
Type
1 way, 1 speaker system
(Bass reflex)
Speaker unit(s)
Full range
Full range
8 cm Cone type
Impedance
6
Ω
Frequency range
60 Hz to 25 kHz (-16 dB)
90 Hz to 22 kHz (-10 dB)
90 Hz to 22 kHz (-10 dB)
Q General
Power supply
Power supply
AC 220 to 240 V, 50 Hz
Power consumption
12 W
Dimensions (W x H x D)
400 mm x 221 mm x 110 mm
[D = 69 mm (min)]
Mass (weight)
2.0 kg
Operating temperature range
0
°C to +40°C
Operating humidity range
35% to 80 % RH
(no condensation)
Power consumption in standby mode: 0.2 W (approximate)
• Specifications are subject to change without notice. Mass and
dimensions are approximate.
• Total harmonic distortion is measured by the digital spectrum ana-
lyzer.
12
5 Location of Controls and Components
5.1.
Main Unit & Remote Control Key Button Operations
Click on the first or last page to see other SC-HC15EB / SC-HC15EG / SC-HC15EP service manuals if exist.