Panasonic SA-VK870EE / SC-VK870EE Service Manual ▷ View online
8.2.6. Optical Pick-up Self-Diagnosis
The optical pickup self-diagnosis function and tilt adjustment check function have been included in this unit. When repairing, use
the following procedure for effective self-diagnosis and tilt adjustment. Be sure to use the self-diagnosis function before replacing
the optical pickup when “NO DISC” is displayed. As a guideline, you should replace the optical pickup when the value of the laser
drive current is more than the specified value.
the following procedure for effective self-diagnosis and tilt adjustment. Be sure to use the self-diagnosis function before replacing
the optical pickup when “NO DISC” is displayed. As a guideline, you should replace the optical pickup when the value of the laser
drive current is more than the specified value.
Note:
Press the power button to turn on the power, and check the value within three minutes before the unit warms up. (Otherwise,
the result will be incorrect.)
the result will be incorrect.)
"NO DISC" is displayed, unit
does not play smoothly, etc.
does not play smoothly, etc.
Check the laser drive current.
Replace the traverse unit.
(Refer to the section "OPTICAL
PICKUP REPLACEMENT
PROCEDURE" in this Guide.)
(Refer to the section "OPTICAL
PICKUP REPLACEMENT
PROCEDURE" in this Guide.)
Initialize the main unit.
Value is more than
37 (DVD), 41 (CD).
37 (DVD), 41 (CD).
Replace with a new optical pickup if the present
value is more than 37 (DVD), 41 (CD).
Cause: Damage due to static electricity
value is more than 37 (DVD), 41 (CD).
Cause: Damage due to static electricity
during replacement.
Use the optical pickup self-diagnosis function.
Method: With no disc in the main unit:
• Press the "FUNCTIONS" button on the remote
• Press the "FUNCTIONS" button on the remote
control unit while pressing the "STOP"
button on the main unit. (DVD)
button on the main unit. (DVD)
• Press the "3" button on the remote
control unit while pressing the "STOP"
button on the main unit. (CD)
[Display content (display1/display2)]
LDD
(DVD)
LDC
(CD)
Factory setting
Present value
Factory setting
Present value
/
/
29
SA-VK870EE
8.3. Service Mode Table (For CR14)
8.3.1. Service Mode Table 1
In self-diagnostic mode, press [1]
button on main unit.
button on main unit.
To exit, power off the main unit
Press [EXCHANGE] on main unit
for error code.
for error code.
FL Display
Key Operation
Front Key
Item
Description
Mode Name
In DVD/CD mode (ensure no disc is
inserted):
Press and hold [STOP] button for five
seconds, followed by [ /FF/ ]
button on the main unit.
inserted):
Press and hold [STOP] button for five
seconds, followed by [ /FF/ ]
button on the main unit.
To exit, press [ , AC IN] button on
main unit or remote control unit.
main unit or remote control unit.
To enter into self-diagnostic checking
for CR14 mechanism.
for CR14 mechanism.
Self-Diagnostic
Mode
Mode
To unlock the mechanism unit for
service.
service.
In this mode, the disassembly of CR14
can be carry out. (Refer to original
service manual for CR14)
can be carry out. (Refer to original
service manual for CR14)
1. All trays are set to "STOCK" position.
2. Mechanism set to tray 1.
3. Cam gear set to "HOME" position.
2. Mechanism set to tray 1.
3. Cam gear set to "HOME" position.
Service Mode 1
In self-diagnostic mode, press [2]
button on main unit.
button on main unit.
To exit, power off the main unit
Press [EXCHANGE] on main unit
for error code.
for error code.
To unlock the traverse unit for service.
In this mode, traverse unit can be
disassembled. (Refer to original
service manual for CR14)
disassembled. (Refer to original
service manual for CR14)
1. Tray 5 set to "Play" position.
2. Mechanism set to tray 5.
3. Cam gear set to "HOME" position.
2. Mechanism set to tray 5.
3. Cam gear set to "HOME" position.
Service Mode 2
/l
(Refer to section 8.6.1. for information)
30
SA-VK870EE
8.3.2. Service Mode Table 2
FL Display
Key Operation
Front Key
Item
Description
Mode Name
The counter will
increment by one.
When reach 99999
will change to 00000
increment by one.
When reach 99999
will change to 00000
In this mode, the trays are loaded &
unloaded.
unloaded.
In self-diagnostic mode, press [1]
button on remote control.
button on remote control.
To exit, press [ ] button on the
main unit or remote control unit.
main unit or remote control unit.
Reliability
1
(Load cycle Test)
To determine open/close operation of the
mechanism (all trays).
mechanism (all trays).
In self-diagnostic mode, press [2]
button on remote control.
button on remote control.
To exit, press [ ] button on the
main unit or remote control unit.
main unit or remote control unit.
Reliability
2
(Traverse Cycle
Test)
To determine playability operation.
In self-diagnostic mode, press [3]
button on remote control.
button on remote control.
To exit, press [ ] button on the
main unit or remote control unit.
main unit or remote control unit.
Reliability
3
(Combi Cycle
Test)
The combine test for both load &
traverse cycle test.
traverse cycle test.
/l
/l
/l
Display 1
Display 2
The counter will
increment by one.
When reach 99999
will change to 00000
increment by one.
When reach 99999
will change to 00000
Display 1
Display 2
The counter will
increment by one.
When reach 99999
will change to 00000
increment by one.
When reach 99999
will change to 00000
Display 1
Display 2
31
SA-VK870EE
8.4. DVD Self Diagnostic Function-Error Code
8.4.1. DVD Module Error Code Table
Error
Code
U702 HDMI/DVI I2C
The communication error of I2C when
Press [ STOP] on main
communication error
connecting it with HDMI/DVI. For
unit for next error.
instance, when EDID information to which
information on the TV set side has been
described cannot be read, it is generated.
U703 HDMI/DVI attestation
When attestation (HDCP) with the TV
Press [ STOP] on main
error
side fails when connecting it with
unit for next error.
HDMI/DVI, it is generated.
U704 HDMI/DVI SRM
It is generated at the equipment to which
Press [ STOP] on main
Riborcerar
the TV set is Riborced when connecting it
unit for next error.
with HDMI/DVI.
U705 HDMI/DVI SRM disk
It is generated at the time of it is time
Press [ STOP] on main
falsification check
when illegal the SRM data of the
unit for next error.
error
reproducing disk (verify error), when
connecting it with HDMI/DVI.
F740 HDMI device key
I2C error when writing HDMI Key device
Press [ STOP] on main
into transmitter.
unit for next error.
F893 FLASH ROM IC data
Firmware error, DV5.0 LSI IC (IC8651)
Press [ STOP] on main
falsification error
error.
unit for next error.
F894 EEPROM IC
When failing in the access to EEPROM
Press [ STOP] on main
abnormality error
IC located in the DVD Module P.C.B.
unit for next error.
(IC8611).
F895 Language area
Firmware version agreement check for
Press [ STOP] on main
abnormal
factory preset setting failure prevention.
unit for next error.
F897 Initialization
Incomplete initialization after writing of
Press [ STOP] on main
error
new firmware (Factory preset setting
unit for next error.
failure prevention)
F899 The communication
Unsuitable combination of number of
Press [ STOP] on main
specification
system com and panel com used.
unit for next error.
disagreement
(Frimware)
between
micro-processor
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
32
SA-VK870EE
Click on the first or last page to see other SA-VK870EE / SC-VK870EE service manuals if exist.