DOWNLOAD Panasonic SA-PTX7EB / SA-PTX7EG Service Manual ↓ Size: 9.74 MB | Pages: 127 in PDF or view online for FREE

Error 

Code
U702 HDMI/DVI I2C

The communication error of I2C

Press [     STOP] on 

communication error when connecting it with HDMI/

main unit for next error.

DVI. For instance, when EDID 
information to which information on the
TV set side has been described 
cannot be read, it is generated. 

U703 HDMI/DVI attestation When attestation (HDCP) with the TV 

Press [     STOP] on 

error

side fails when connecting it with 

main unit for next error.

HDMI/DVI, it is generated.

U704 HDMI/DVI SRM

It is generated at the equipment to

Press [     STOP] on 

Riborcerar

which the TV set is Riborced when

main unit for next error.

connecting it with HDMI/DVI.

U705 HDMI/DVI SRM disk

It is generated at the time of it is time 

Press [     STOP] on 

falsification check 

when illegal the SRM data of the 

main unit for next error.

error

reproducing disk (verify error), when
connecting it with HDMI/DVI.

F740 HDMI device key

I2C error when writing HDMI Key 

Press [     STOP] on 

device into transmitter. 

main unit for next error.

F893 FLASH ROM IC data  Firmware error, DV5 LSI IC (IC8651)

Press [     STOP] on 

falsification error

error.

main unit for next error.

F894 EEPROM IC

When failing in the access to

Press [     STOP] on 

abnormality error

EEPROM IC located in the DVD 

main unit for next error.

(HDMI) Module P.C.B. (IC8611)

F895 Language area 

Firmware version agreement check for 

Press [     STOP] on 

abnormal

factory preset setting failure 

main unit for next error.

prevention.

F896 No existence model

Firmware version agreement check for 

Press [     STOP] on 

factory preset setting failure 

main unit for next error.

prevention.

F897 Initialization 

Incomplete initialization after writing of

Press [     STOP] on 

error

new firmware (Factory preset setting

main unit for next error.

failure prevention)

F898 Disagreement of

Unsuitable combination of AV Decoder,

Press [     STOP] on 

hardware and 

SDRAM & FLASH ROM IC (firmware).

main unit for next error.

software

F899 The communication

Unsuitable combination of number of 

Press [     STOP] on 

specification 

system com and panel com used.

main unit for next error.

disagreement

(Frimware)

between 
micro-processor

Diagnosis Contents

Description of error

Automatic FL Display

Remarks

49

Error 

Code

F61 The abnormalities

In normal operation, when DCDET2 

Press [     STOP] on 

in an output or power

goes to "L" (Low) (Not during POWER 

main unit for next error.

supply circuit of 

OFF condition), F61 appears on FL 

POWER AMP

Display and PCONT goes to "L" (Low).
This is due to speaker output has DC
voltage or fan is not working. 

F76 Abnormality in the 

In normal operation when DCDET1 is

Press [     STOP] on 

output voltage of 

detected "L" (Low) for two consecutive 

main unit for next error.

stabilized power 

times, F76 is displayed on FL for 2

supply

seconds and after that PCONT will be 
turned to "L" (Low). This is due to any of
the DC voltages (+9V, +7V, -7V, +5V, 
+5.3V etc.) not available.

H19

Abnormality in the 

When the fan motor stops operating 

Press [     STOP] on 

fan operation

during power-up at normal operation. 

main unit for next error.

After 1 seconds, the unit will 
automatically shutdown to standby 
mode after the error code appears on 
the FL display.

U59

Abnormality in the 

When there is a detection of 

Press [     STOP] on 

digital amp IC

abnormality to the digital amp IC at

main unit for next error.

time of normal operation. After 1 
seconds, the unit will automatically 
shutdown to standby mode after the 
error code appears on the FL display.

Diagnosis Contents

Description of error

Automatic FL Display

Remarks

Error 

Code

F600 Administrative 

It becomes impossible NaviPack etc.

Press [     STOP] on 

information cannot 

were done, and not to be able to 

main unit for next error.

be acquired by the

acquire necessary information in the 

recovery error.

navigation’s changing due to wound 
etc. of DISC, and to have done the 
reproduction transition. 

F601 Irregular sector ID

It tried to access the position that did 

Press [     STOP] on 

was demanded.

not exist on DISC by the recording 

main unit for next error.

error etc. of authoring. 

F603 KEYDET cannot be The data for decoding copyright 

Press [     STOP] on 

acquired by the 

protection (CSS) cannot be acquired

main unit for next error.

recovery error. 

due to wound etc. of DISC, and it is not
possible to reproduce. 

Diagnosis Contents

Description of error

Automatic FL Display

Remarks

50

Error 

Code

F650 USB device: Devices Devices other than the mass storage 

Press [     STOP] on 

other than mass 

class are connected.

main unit for next error.

storage

F651 USB device: Non-

The device that the transfer rate did not

Press [     STOP] on 

Full Speed Device

correspond to Full Speed was

main unit for next error.

connected. 

F652 USB device: 

The device in the interface (subclass)

Press [     STOP] on 

Interface NG

outside correspondence was

main unit for next error.

connected. (correspondence interface)
001b: Reduced Block Commands
          (RBC)
010b: SFF-8020i. MMC-2 (ATAPI)
110b: SCSI transparent command set.

F655 USB device: 

The overcurrent of 500mA or more was

Press [     STOP] on 

Overcurrent 

detected in VDD USB, and the USB 

main unit for next error.

detection

device driver function was intercepted.
(To intercept the current.)

Diagnosis Contents

Description of error

Automatic FL Display

Remarks

This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function.
"LOCKED" is displayed on the unit, and ordinary operation is disabled.

     ·    Prohibiting removal of disc

 1. Select the DVD/CD function.
 2. At POWER ON condition, press and hold down the

button and the power button on the player for at least three

seconds. (The message, “___LOCKED_” appears when the function is activated.)

OPEN/CLOSE

button is invalid and the player displays “___LOCKED_” while the lock function mode is entered.

     ·    Prohibiting operation of selector and disc

 1. Select the DVD/CD function.
 2. At POWER ON condition, press and hold down the

button and the power button on the player for at least three

seconds. (The message, “___LOCKED_” appears when the function is activated.)

The following buttons are invalid and the player displays “___LOCKED_” while the lock function mode is entered.

Player

OPEN/CLOSE

, CD

/ HDD

, SELECTOR

, SELECTOR

,

,

/

,

/

Remote

controller unit

HDD (MUSIC COLLECTION), TUNER, SELECTOR <, SELECTOR >, NUMERIC KEYS 0~9,

,

,

,

,

,

,

, CANCEL, HDD REC, PLAY MODE, SETUP, START, SUBMENU.

The lock can be cancelled by the same procedure as used in setting. ("UNLOCKED" is displayed on cancellation. Disconnecting
the power cable from power outlet does not cancel the lock.)

     ·    When the FLASH ROM IC or DVD Module P.C.B. is replaced, carry out the recovery processing to optimize the drive.

51

Playback the recovery disk to process the recovery automatically.

     ·    Recovery disc (Product number: RFKZD03R005) [SPG]
     ·    Performing recovery process

 1. Load the recovery disc RFKZD03R005 on to the player and run it.
 2. Recovery is performed automatically. When it is finished, a message appears on the screen.
 3. Remove the recovery disc.
 4. Turn off the power.
 5. Initialize the player.

     ·    The firmware of the DVD player may be renewed to improve the quality including operability and playability to the substandard

discs.processing to optimize the drive.

The recovery disc has also firmware version-up.

     ·    After version-up, recovery processing is executed automatically.
     ·    Part number of the recovery disc for version-up will be noticed when it is supplied.
     ·    Updating firmware

 1. Load the recovery disc on to the player and run it.
 2. Firmware version of the player is automatically checked. Appropriate message appears whenever necessary.
 3. Using remote controller´s cursor key, select whether version updating is to be done or not. (Selection of Yes/No)
 4. a. If Yes is selected, version updating is performed.

b. If No is selected, only recovery is performed.

 5. a. When updating is finished, remove the disc according to the message appearing on the screen.

b. Remove the disc according to the message appearing on the screen.

 6. Turn off the power.

If the AC power supply is shut out during version-up due to a power failure, the version-up is improperly carried out.
In such a case, replace the FLASH ROM IC and carry out the version-up again.

     ·    When after replacing FLASH ROM IC or DVD Module P.C.B., FL displays error code “ DVD F897”. This means the unit is not

initialized properly and the following process needs to be carry out.

     ·    Procedures:

 1. Press

on remote control while pressing “STOP” button on main unit. (To enter into initialization)

 2. FL display show “INIT”
 3. While still pressing “STOP” button on main unit, press “ENTER” on remote control. (To reset the unit)
 4. FL will display “RESET” before FL display will change to TOC reading again.
 5. Power off unit. Unplug the AC cord.
 6. Power on the unit. It should be no problem. If problem persist check on the DVD Module P.C.B. or FLASH ROM IC.

52