Panasonic SA-PT22GC / SA-PT22GW Service Manual ▷ View online
21
6.2.3.
Service Mode Table 3 (For DVD)
FL Display
Key Operation
Front Key
Item
Description
Mode Name
Initialization
Micro-processor
firmware version
display &
EEPROM
checksum
display.
DVD
Module P.C.B.
Reset
Initialization.
User settings are cancelled and player
is initialized to factory setting.
It is necessary when after replacement
of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM
IC (IC8611) & DVD Module P.C.B.
User settings are cancelled and player
is initialized to factory setting.
It is necessary when after replacement
of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM
IC (IC8611) & DVD Module P.C.B.
Micro-processor firmware version
display & EEPROM checksum display.
EEPROM checksum is only available
due to existence of EEPROM IC.
display & EEPROM checksum display.
EEPROM checksum is only available
due to existence of EEPROM IC.
Note: Condition 1/2/3 shows the state
of EEPROM IC.
of EEPROM IC.
FL Display sequence:
Display 1 2 3.
Display 1 2 3.
To reset DVD Module P.C.B.
This process is used when the DVD
Module P.C.B. or FLASH ROM
IC is replaced with a new one.
This process is used when the DVD
Module P.C.B. or FLASH ROM
IC is replaced with a new one.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [ 10] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [ 10] button on the
remote control unit.
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [7] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [7] button on the
remote control unit.
Press [FL Display] button on
remote control unit for next
page. (FL Display)
remote control unit for next
page. (FL Display)
While in initialization
mode, press & hold
[STOP] button on the main
unit for 3 seconds, follow
by [OK] button on the
remote control unit.
mode, press & hold
[STOP] button on the main
unit for 3 seconds, follow
by [OK] button on the
remote control unit.
(Display 2)
If the version of the EEPROM does not match,
[NG] is displayed.
[NG] is displayed.
(Condition 1)
(a) If there is NO EEPROM header string
OR
(b) If there is no EEPROM (no data is received
by Micro-processor), [NO] is displayed.
OR
(b) If there is no EEPROM (no data is received
by Micro-processor), [NO] is displayed.
(Condition 2)
Opecon
Version
Version
EEPROM
Checksum
(If applicable,
refer below.)
Checksum
(If applicable,
refer below.)
(Display 3)
(Display 1)
(Condition 3)
If the EEPROM version matches, checksum
[YYYY] is displayed.
[YYYY] is displayed.
22
6.2.4.
Service Mode Table 4 (For DVD)
FL Display
Key Operation
Front Key
Item
Description
Mode Name
DVD
Module P.C.B.
firmware
version display
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [8] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [8] button on the
remote control unit.
DVD Module P.C.B. firmware version is
displayed on the FL Display.
The firmware version can be updated
using recovery disc.
displayed on the FL Display.
The firmware version can be updated
using recovery disc.
Note: It is necessary to check for
firmware version before carrying out
the version up using the disc.
firmware version before carrying out
the version up using the disc.
Destination
System
controller
version
controller
version
System controller
generation
generation
Region No.: 0-8
Timer 1 check
DVD laser usage time
(Display 1)
Shown to the above is DVD laser usage
time, and to the below is CD laser usage
time.
Time is shown in 5 digits of decimal notation
in a unit of 10 hours.
"00000" will follow "99999". (DVD laser)
time, and to the below is CD laser usage
time.
Time is shown in 5 digits of decimal notation
in a unit of 10 hours.
"00000" will follow "99999". (DVD laser)
(Display 2)
CD laser usage time
Time is shown in 6 digits of decimal notation
in a unit of 10 hours.
"000000" will follow "999999". (CD laser)
in a unit of 10 hours.
"000000" will follow "999999". (CD laser)
Press [FL Display] button for
next page of FL Display.
next page of FL Display.
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [ ] button
on the remote control unit.
press [STOP] button on the
main unit, and [ ] button
on the remote control unit.
Timer 1 reset
Timer 2 check
Timer 2 reset
Timer 1 check
Laser operation timer is measured
separately for DVD laser and CD laser.
Laser operation timer is measured
separately for DVD laser and CD laser.
FL Display sequence:
Display 1 2.
Display 1 2.
Timer 1 reset
Laser operation timer of both DVD
laser and CD laser is reset all at once.
Laser operation timer of both DVD
laser and CD laser is reset all at once.
Timer 2 check
Spindle motor operation timer
Spindle motor operation timer
Timer 2 reset
Spindle motor operation timer
Spindle motor operation timer
Time is shown in 5 digits of decimal notation
in a unit of 10 hours.
It will clear to "00000" upon reset.
in a unit of 10 hours.
It will clear to "00000" upon reset.
Time is shown in 5 digits of decimal notation in
a unit of 1 hour.
"00000" will follow "99999".
a unit of 1 hour.
"00000" will follow "99999".
Time is shown in 5 digits of decimal notation in
a unit of 1 hour.
It will be cleared to "00000" upon activating
this.
a unit of 1 hour.
It will be cleared to "00000" upon activating
this.
Cancelled automatically
5 seconds later
5 seconds later
While displaying Timer 1
data, press [STOP] button
on the main unit, and [ ]
button on the remote control
unit.
data, press [STOP] button
on the main unit, and [ ]
button on the remote control
unit.
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [ ] button
on the remote control unit.
press [STOP] button on the
main unit, and [ ] button
on the remote control unit.
Cancelled automatically
5 seconds later.
5 seconds later.
While displaying Timer 2
data, press [STOP] button
on the main unit, and [ ]
button on the remote
control unit.
data, press [STOP] button
on the main unit, and [ ]
button on the remote
control unit.
23
Figure 6.1 Video Design Information
English (NA), Spanish (NA),
Canadian, French
Canadian, French
(S)
Japanese, English
English (EU), French, German,
Spanish (EU), Polish, Russian,
Czech, Hungarian
Spanish (EU), Polish, Russian,
Czech, Hungarian
English (EU), French, German,
Italian, Spanish (EU), Polish,
Swedish, Dutch
Italian, Spanish (EU), Polish,
Swedish, Dutch
English (NA), French, German,
Spanish (EU), Polish, Russian,
Czech, Hungarian
Spanish (EU), Polish, Russian,
Czech, Hungarian
GA, GD
GT, GJ
GT, GJ
English (NA), Traditional
Chinese
Chinese
English (EU), French, German,
Italian, Spanish (EU), Polish,
Swedish, Dutch
Italian, Spanish (EU), Polish,
Swedish, Dutch
English (NA), Spanish (Panama),
French, Brazilian Portuguese
French, Brazilian Portuguese
English (EU), French, German,
Spanish (EU), Polish, Russian,
Czech, Hungarian
Spanish (EU), Polish, Russian,
Czech, Hungarian
GN
EE
PH, PU,
PR
PR
EP
P, PC, PX
GC, GS
EB, EG, ES
2
5
4
4
2
2
1
2
3
Region
Code
NTSC
PAL
NTSC
NTSC
SECAM
NTSC
PAL
PAL
PAL
NTSC
PAL
TV Broadcasting
System
NTSC (*A)
NTSC (*D)
NTSC (*D)
PAL (*C)
PAL (*C)
PAL (*C)
PAL (*C)
PAL (*C)
NTSC (*A)
NTSC (*B)
Signal System
(Default)
2PN
4PN
4PN
5P6
3PN
4P6
2P6
2P6
1PN
2P6
Region Display
(Default)
Product
Model Series
Japan
South East Asia,
Korea, Taiwan
Korea, Taiwan
New Zealand,
Australia
Australia
South/Central
America, Argentina
America, Argentina
CIS
Poland, E.Europe
USA, Canada,
US Militry
US Militry
UK, Germany,
W.Europe
W.Europe
Middle East,
Africa, S.E.A
Africa, S.E.A
Country Region
OSD Menu Language
OSD
Default
English
English
English
English
English (NA), Traditional
Chinese
Chinese
GW
5
PAL
PAL (*C)
5P6
India
English
English
English
English
English
GK
English (NA), Simplified Chinese
6
PAL
NTSC (*B)
6PN
China
Simplified
Chinese
Chinese
Japanese
English (NA), Spanish (Panama),
French, Brazilian Portuguese
French, Brazilian Portuguese
PN
4
NTSC
Central &
S.America, Brazil
S.America, Brazil
Spanish
NTSC (*D)
4PN
English (NA), Spanish (Panama),
French, Brazilian Portuguese
French, Brazilian Portuguese
PB
4
NTSC
Central &
S.America, Brazil
S.America, Brazil
Portuguese
NTSC (*B)
Source
Output
Screen Saver
NTSC
NTSC disc
NTSC (default)
PAL60
PAL disc
PAL
NTSC (*A)
Source
Output
Screen Saver
NTSC
NTSC disc
NTSC
PAL disc
PAL (DVD-V)
NTSC (DVD-A/VCD)
NTSC (*D)
Source
Output
Screen Saver
NTSC
NTSC disc
NTSC
PAL disc
NTSC
PAL (*C)
Source
Output
Screen Saver
PAL
NTSC disc
PAL60 (default)
NTSC
PAL disc
PAL
Explanation of Display
Individual Model Code
Can play PAL disc
Region code
N: If NTSC disc is played, NTSC output.
6: If NTSC disc is played, PAL60 output.
6: If NTSC disc is played, PAL60 output.
24
6.3.
Self-Diagnostic Mode
Delete Error
Codes
Codes
Error code
information
information
System will perform a check on
any unusual/error code from the
memory
any unusual/error code from the
memory
Error code will display
Example:
In self-diagnostic mode,
press [STOP] on remote
control.
press [STOP] on remote
control.
To exist, press [ / ]
on main unit or remote
control.
on main unit or remote
control.
Self-Diagnostic
Mode
Mode
To enter into self-diagnostic checking
for DLS6E Mechanism
for DLS6E Mechanism
Press & hold [STOP] on main
unit, follow by [4] then [9] on
remote control. (When no
disc in mechanism)
unit, follow by [4] then [9] on
remote control. (When no
disc in mechanism)
System will clear all of the contents
of unusual/error code from the
memory
of unusual/error code from the
memory
FL Display
Key Operation
Front Key
Item
Description
Mode Name
In self-diagnostic mode,
press [CANCEL] on remote
control.
press [CANCEL] on remote
control.
To exist, press [ / ]
on main unit or remote
control.
on main unit or remote
control.
Click on the first or last page to see other SA-PT22GC / SA-PT22GW service manuals if exist.