DOWNLOAD Panasonic SA-PT22GC / SA-PT22GW Service Manual ↓ Size: 6.62 MB | Pages: 122 in PDF or view online for FREE

17

18

Here is the procedure to carry out cold-start or initialize to shipping mode.

1. Unplug AC power cord
2. Press & hold [POWER] button
3. Plug AC power cord while [POWER] button being pressed

FL Display will show “_ _ _ _ _ _ _ _”

4. Release [POWER] button

By pressing various button combinations on the main unit and remote control unit, you can activate the various service modes for
checking.
Special Note:

• Due to the limitations of the no. characters that can be shown on the FL Display, the “FL Display” button on the remote control

unit can be used to show the two display pages. (Display 1 / Display 2).

• Refer to Section 5.1 for the section on “Remote Control Key Buttons Operations”.

19

Initial setting of

laser drive

current

Jitter check

Jitter check.
Jitter rate is measured and displayed.
Measurement is repeatedly done in 
the cycle of one second. Read error 
counter starts from zero upon mode 
setting.
When target block data failed to be 
read out, the counter advances by one 
increment. When the failure is caused 
by minor error, it may be corrected 
when retried to enable successful 
reading.
In this case, the counter advances by 
one. When the error persists even 
after retry, the counter may jump by 
two or more.

FL Display sequence:
Display 1    2.

Jitter rate is shown in decimal notation to one 
place of decimal.
Focus drive value is shown in hexadecimal 
notation.

(Display 1)

Jitter rate

Jitter check
mode

(Display 2)

Lead
Error
Counter

Focus Drive 
Value

Press [POWER] or [STOP]
button to exit.

In STOP (with disc inside 
tray) mode, press [STOP] 
button on the main unit, 
and [5] button on 
the remote control unit.

Press [FL Display] on 
remote control unit for next
page (FL Display).

Error code

check

Error code check
The latest error code stored in the 
EEPROM IC is displayed.

Note: Refer to "[Section 6.4] DVD Self
Diagnostic Function-Error Code" for 
more detailed information on the error 
codes.

Error code (play_err) is expressed in the 
following convention.
Error code = 0 x DAXX is expressed: 

DVDnn U12

Error code = 0 x DBXX is expressed: 

DVDnn H12

Error code = 0 x DXXX is expressed: 

DVDnn F123

Error code = 0 x 0000 is expressed: 

DVDnn F---

* "xx" denotes the error code

F / H / U

To exit, press [POWER]
button on main unit or 
remote control.

In STOP (no disc) mode, 
press [STOP] button on the 
main unit, and [0] button on 
the remote control unit. 
*With pointing of cursor up 
and down on display.

Press [FL Display] on 
remote control unit for next
page (FL Display) on values
of laser drive current.

In STOP (no disc) mode, 
press [STOP] button on the 
main unit, and [PAUSE] 
button on the remote 
control.

Initial setting of laser drive current. 
Initial current value for the DVD laser 
and CD laser is separately saved in 
the EEPROM IC.

FL Display sequence:
Display 1    2.

The value denotes the current in decimal 
notation.

The above example shows the initial current 
is XXXmA and YYYmA for CD laser and 
DVD laser respectively when the laser is 
switched on.

(Display 1)

Laser current
measurement
mode

(Display 2)

CD
Laser

DVD Laser 

FL Display

Key Operation

Front Key

Item

Description

Mode Name

20

FL Display

Key Operation

Front Key

Item

Description

Mode Name

CD laser drive 

current

measurement

Press [FL Display] on 
remote control unit for next
page. (FL Display)

In STOP (no disc) mode, 
press [STOP] button on 
the main unit, and [3] 
button on the remote 
control unit.

The value denotes the current in decimal 
notation.

The above example shows the initial current is 
XXXmA and the measured value is YYYmA.

DVD laser 

drive current 

measurement

CD laser current 
measurement mode

(Display 1)

CD
laser initial
value

CD laser
value

(Display 2)

Press [FL Display] on 
remote control unit for next
page (FL Display) on values
of dvd drive current. 

In STOP (no disc) mode, 
press [STOP] button on the 
main unit, and 
[FUNCTIONS] button on 
the remote control unit.

The value denotes the current in decimal 
notation.

The above example shows the initial current 
is XXXmA and the measured value is 
YYYmA.

DVD laser current 
measurement mode

(Display 1)

DVD
Laser
Initial Value

DVD
Laser
Value

(Display 2)

DVD laser drive current measurement. 
DVD laser drive current is measured 
and the result is displayed together 
with the initial value stored in the 
EEPROM IC.
After the measurement, DVD laser 
emission is kept on. It is turned off 
when POWER key is switched off.

FL Display sequence:
Display 1    2.

CD laser drive current measurement.
CD laser drive current is measured 
and the result is displayed together 
with the initial value stored in the 
EEPROM IC.
After the measurement, CD laser 
emission is kept on. It is turned off 
when POWER key is switched off.

FL Display sequence:
Display 1    2. 

Region code display, TV broadcasting
system & the model no. information.

Note: Refer to Figure 6.1 for "Video
Design Information".

Region display

Display is automatically
clear after 5 seconds.

In STOP (no disc) 
mode, press [STOP] 
button on the main unit, 
and [6] button on the 
remote control unit.

N: no PAL / P: PAL

Model
No.
Information

N: NTSC / 6: PAL60

Region No.: 0-8

CPPM/CRM

Keys Check

Cancelled automatically 
5 seconds later.

In STOP (no disc) 
mode, press [STOP] 
button on the main unit, 
and [SOUND] button on 
the remote control unit.

0: NG
1: OK

0: NG
1: OK

CPPM/CRM refers to the Content 
Protection for Recordable Media and 
Pre-Recorded Media. It displays the 
existence of the keys as "1" or "0".
OK: Existing of keys.
NG: Non existing of keys.