DOWNLOAD Panasonic CS-VE9NKE / CS-VE12NKE / CU-VE9NKE / CU-VE12NKE Service Manual ↓ Size: 12.33 MB | Pages: 127 in PDF or view online for FREE

97 

6  Disengage the tabs (5 locations) which fix the control board and then remove the control board. 

 

 

1  Perform “16.1.1 Removing the Front Panel”. 
2  Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”. 



 Note on disassembly: When removing only the control board (emergency operation switch and buzzer), 

remove the front grille (right) only. 

3  Remove the electrical component cover (front) on the right side of the control board box. (There are two tabs 

on top and one tab at the bottom.) 

 

 

 

4  Disconnect the connector CN-SWSEN (white) connected to the control board. 
5  Press the tab (1 location) on top of the control board (emergency operation switch & buzzer) and remove the 

control board (emergency operation switch and buzzer). 

 

 

98 

1  Perform “16.1.1 Removing the Front Panel”. 
2  Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”. 
3  Disengage the tabs (2 locations) on both sides of the indicator panel. Then, remove the indicator panel. 

 

 

 

4  Flip the indicator panel and remove the screws (2 pieces). 

 

 

 



 How to remove the human and object sensor 

1  Disconnect the connectors (2 locations) for the control board (signal receptor). 
2  Remove the fixing screw (1 piece) of the human and object sensor. Then, remove the human and object 

sensor. 

 

 

 

3  Remove the electrical component cover (front) on the right side of the control board box. (There are two tabs 

on top and one tab at the bottom.) 

 

 

99 

4  Disconnect the connector CNSTM4 (blue) connected to the control board. 

 



 How to remove the control board (signal receptor) 

1  Disconnect the connectors (3 locations) and disengage the tabs (3 locations) on the control board (signal 

receptor). Then, remove the control board (signal receptor). 

 

 

 



 How to remove the control board (indicator) 

1  Disengage the tabs (2 locations) on the plastic indicator cover. 

 

 

 

2  Flip the plastic indicator cover and disengage the tabs (5 locations). 

 

 

 

3  Disconnect the connector (1 location) on the control board (signal receptor). 
4  Disconnect the connectors (2 locations) on the control board (indicator) and remove the control board 

(indicator). 

 

 

100 



 How to remove the lower louver of the vertical airflow direction louver 

1  Open the lower louver. 
2  The back side of the lower louver is designed as follows: left – inserting type; center – hook engaging type; 

and right – inserting into the motor type. Push the center hook to the right to disengage it. 

3  Warp the center part of the lower louver towards you and pull out the left shaft and then the right shaft. Then, 

remove the lower louver. 

 

 

 



 How to remove the upper louver of the vertical airflow direction louver 

1  Open the lower louver and then open the upper louver. 

 

 

 

2  The back side of the upper louver is designed as follows: left – inserting type; center – hook engaging type; 

and right – inserting into the motor type. Push the center hook to the left to disengage it. 

3  Warp the center part of the upper louver towards you and pull out the left shaft and then right shaft. Then, 

remove the upper louver.