Panasonic CS-VE9NKE / CS-VE12NKE / CU-VE9NKE / CU-VE12NKE Service Manual ▷ View online
101
16.1.9 Removing the Blowout Grille
1 Perform “16.1.1 Removing the Front Panel”.
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Remove the screws (1 piece each on right and left) located at the bottom side of the blowout grille.
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Remove the screws (1 piece each on right and left) located at the bottom side of the blowout grille.
6 Remove the accessory panel below the framework.
7 Disconnect the drain hose and pull the blowout grille to remove it.
Note on disassembly: Be careful of the water in the drain hose and drain pan.
102
16.1.10 Removing the Drive Motor of the Vertical Airflow Direction Louver (Upper and
Lower Louvers)
1 Perform “16.1.1 Removing the Front Panel”.
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Perform “16.1.9 Removing the Blowout Grille”.
6 Remove the drive motor fixing screws (2 pieces each) on the right side of the blowout grille. Then, remove
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Perform “16.1.9 Removing the Blowout Grille”.
6 Remove the drive motor fixing screws (2 pieces each) on the right side of the blowout grille. Then, remove
the lower louver driving motor and upper louver driving motor.
16.1.11 Removing the Drive Motor of the Horizontal Airflow Direction Louver (Right and
Left Louvers)
1 Perform “16.1.1 Removing the Front Panel”.
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Perform “16.1.9 Removing the Blowout Grille”.
6 Remove the lower louver drive motor according to “16.1.12 Removing the Drive Motor of the Vertical Airflow
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Perform “16.1.9 Removing the Blowout Grille”.
6 Remove the lower louver drive motor according to “16.1.12 Removing the Drive Motor of the Vertical Airflow
Direction Louver (Upper and Lower Louvers)”.
7 Remove the horizontal louver (right) drive motor.
o
Remove the drive motor fixing screws (2 pieces) on the right side of the blowout grille and then remove
the horizontal louver (right) drive motor.
the horizontal louver (right) drive motor.
103
8 Remove the horizontal louver (left) drive motor.
o
Remove the drive motor fixing screw (1 piece) on the right side of the blowout grille.
o
Push the drive motor fixing tab (1 location) towards the direction indicated by the arrow to disengage it.
9 Release the lever from the horizontal louver and remove the drive motor. (A lever is connected to the
horizontal louver drive motor (both right and left).
o
Press the stopper of the lever and pull the horizontal louver connecting lever towards you to release the
lever from the horizontal louver.
lever from the horizontal louver.
16.1.12 Removing the Indoor Motor and Cross Flow Fan
1 Perform “16.1.1 Removing the Front Panel”.
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Perform “16.1.9 Removing the Blowout Grille”.
6 Remove the screws (2 pieces) on the left side of the heat exchanger.
2 Perform “16.1.2 Removing the Air Filters”.
3 Perform “16.1.3 Removing the Front Grille (Right) and Front Grille (Left)”.
4 Perform “16.1.4 Removing the Control Board Box”.
5 Perform “16.1.9 Removing the Blowout Grille”.
6 Remove the screws (2 pieces) on the left side of the heat exchanger.
104
7 Loosen the fixing screw (1 screw) which fixes the cross flow fan to the indoor motor.
8 Pull out the cross flow fan while lifting up the left side of the heat exchanger.
9 Remove the screws (3 pieces) of the indoor motor cover and pull out the indoor motor together with the cover
to the right side to remove it.
Click on the first or last page to see other CS-VE9NKE / CS-VE12NKE / CU-VE9NKE / CU-VE12NKE service manuals if exist.