DOWNLOAD Panasonic CS-CE9JKE / CU-CE9JKE / CS-CE12JKE / CU-CE12JKE Service Manual ↓ Size: 5.8 MB | Pages: 84 in PDF or view online for FREE

33

• The horizontal airflow direction louvers can be adjusted manually by hand.

• ON timer can be set using remote control, the unit with timer set will start operate earlier than the setting time. This is to provide

a comfortable environment when reaching the set ON time.

• 60 minutes before the set time, indoor (at fan speed of Lo-) and outdoor fan motor start operate for 30 seconds to determine the

indoor intake air temperature and outdoor air temperature in order to judge the operation starting time.

• From the above judgment, the decided operation will start operate earlier than the set time as shown below.

OFF timer can be set using remote control, the unit with timer set will stop operate at set time.

1. When the power supply is cut off during the operation of air conditioner, the compressor will re-operate within three to four

minutes (there are 10 patterns between 2 minutes 58 seconds and 3 minutes 52 seconds to be selected randomly) after
power supply resumes.

2. This type of control is not applicable during ON/OFF Timer setting.

Note:

• If POWER LED is blinking, the possible operation of the unit are Hot Start, during Deice operation, operation mode judgment, or

ON timer sampling.

• If Timer LED is blinking, there is an abnormality operation occurs.

LED

POWER

TIMER

Color

Green

Orange

Light ON

Operation ON

Timer Setting ON

Light OFF

Operation OFF

Timer Setting OFF

34

• The Compressor will not turn on within 3 minutes from the moment operation stops, although the unit is turned on again by

pressing OFF/ON button at remote control within this period.

• This control is not applicable if the power supply is cut off and on again.
• This phenomenon is to balance the pressure inside the refrigerant cycle.

• Once the air conditioner is turned on, the compressor will not stop within 30 seconds in a normal operation although the intake air

temperature has reached the thermo-off temperature. However, force stop by pressing the OFF/ON button at the remote control
is permitted or the Auto OFF/ON button at indoor unit.

• The reason for the compressor to force operation for minimum 30 seconds is to allow the refrigerant oil run in a full cycle and

return back to the outdoor unit.

1. When the outdoor unit total running current (AC) exceeds X value, the frequency instructed for compressor operation will be

decreased.

2. If the running current does not exceed X value for 5 seconds, the frequency instructed will be increased.
3. However, if total outdoor unit running current exceeds Y value, compressor will be stopped immediately for 3 minutes.

4. The first 30 minutes of cooling operation, (A) will be applied.

A. Overheating Prevention Control

1. When the IPM temperature rises to 100

°C, compressor operation will stop immediately.

2. Compressor operation restarts after 3 minutes the temperature decreases to 95

°C.

3. If this condition repeats continuously 4 times within 20 minutes, timer LED will be blinking (“F96” is indicated).

B. DC Peak Current Control

1. When electric current to IPM exceeds set value of 20.2 A, the compressor will stop operate. Then, operation will restart

after 3 minutes.

2. If the set value is exceeded again more than 30 seconds after the compressor starts, the operation will restart after 1

minute.

3. If the set value exceeded again within 30 seconds after the compressor starts, the operation will restart after 2 minutes. If

this condition repeats continuously for 7 times, all indoor and outdoor relays will be cut off, timer LED will be blinking (“F99”
is indicated).

Model

CE9JK

CE12JK

Operation Mode

X (A)

Y (A)

X (A)

Y (A)

Cooling/Soft Dry (A)

4.95

14.98

5.76

14.98

Cooling/Soft Dry (B)

4.43

14.98

5.24

14.98

Cooling/Soft Dry (C)

4.95

14.98

5.76

14.98

Heating

6.2

14.98

8.1

14.98

35

• Instructed frequency for compressor operation will be regulated by compressor discharge temperature. The changes of

frequency are as below.

• If compressor discharge temperature exceeds 112

°C, compressor will be stopped, occurs 4 times per 20 minutes, timer LED will

be blinking. (“F97” is indicated.)

a. Control start conditions

• For 5 minutes, the compressor continuously operates and outdoor total current is between 0.6A and 1.15A.
• During Cooling and Soft Dry operations:

Indoor suction temperature - indoor piping temperature is below 4

°C.

• During Heating operations :

Indoor piping temperature - indoor suction is under 5

°C.

b. Control contents

• Compressor stops (and restart after 3 minutes).
• If the conditions above happen 2 times within 20 minutes, the unit will:

- Stop operation
- Timer LED blinks and “F91” indicated.

• When the compressor operate at frequency lower than 25 Hz continued for 240 minutes, the operation frequency will be

changed to 24 Hz for 2 minutes.

• When all the below conditions comply, the compressor frequency will change to lower frequency.

Temperature, T, for:

Cooling/Soft Dry

Heating

Indoor intake air (

°C)

T < 14 or T   30

T < 14 or T   28

Outdoor air (

°C)

T < 13 or T   38

T < 4 or T   24

Indoor heat exchanger (

°C)

T < 30

T  

0

36

• The compressor operating frequency is regulated in accordance to the outdoor air temperature as shown in the diagram below.
• This control will begin 1 minute after the compressor starts.
• Compressor frequency will adjust base on outdoor air temperature.

• Detects the Outdoor pipe temperature and carry out below restriction/limitation (Limit the compressor Operation frequency)
• The compressor stop if outdoor pipe temperature exceeds 63

°C.

• If the compressor stops 4 times in 20 minutes, Timer LED blinking (F95 indicated: outdoor high pressure rise protection)

1. When indoor heat exchanger temperature is lower than 0

°C continuously for 6 minutes, compressor will stop operating.

2. Compressor will resume its operation 3 minutes after the indoor heat exchanger is higher than 5

°C.

3. At the same time, indoor fan speed will be higher than during its normal operation.
4. If indoor heat exchanger temperature is higher than 5

°C for 5 minutes, the fan speed will return to its normal operation.

1. Control start conditions

• During Cooling operation and soft dry operation

- During thermo OFF condition, indoor intake temperature is less than 10

°C or

- Compressor stops for freeze prevention control

• Either one of the conditions above occurs 5 times in 60 minutes.

2. Control contents

• Operation stops
• Timer LED blinks and “H99” indicated

• To prevent dew formation at indoor unit discharge area.
• This control will be activated if:

- Outdoor air temperature and Indoor pipe temperature judgment by microcontroller is fulfilled.
- When Cooling or Dry mode is operated more than 20 minutes or more.

• This control stopped if:

- Compressor stopped.
- Remote control setting changed (fan speed / temperature).
- Outdoor air temperature and indoor intake temperature changed.

• Fan speed, angle of louver (vertical airflow angle) will be adjusted accordingly in this control.

- Fan speed will be increased slowly if the unit is in quiet mode but no change in normal cooling mode.