LG WD-3243RHD / WD-3245RHD Service Manual ▷ View online
20
NO
YES
NO
NO
YES
NO
YES
YES
NO
NO
YES
YES
YES
NO
NO
NO
YES
Wiring diagram
Is water supply shut-off?
Is the tap opened?
When you press both RINSE button and SPIN
button simultaneously, is the water level frequency
below 240?
button simultaneously, is the water level frequency
below 240?
Is the inlet valve filter clogged with impurity?
Is resistance between each terminal of INLET
VALVE ASSEMBLY is 2~8
VALVE ASSEMBLY is 2~8
kΩ
?
Check the voltage of the inlet valve connector
120-127V~.
(Refer to 7-2 QC TEST MODE)
Is water supplied?
Are replaceptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
terminals of the INLET VALVE ASSEMBLY?
Is detergent put in the correct compartment of
the drawer?
the drawer?
Is the detergent caked or hardened?
Open the tap.
Check the AIR CHAMBER
and the tube clogged
with impurity.
and the tube clogged
with impurity.
Clean the filter.
Replace the INLET VALVE
ASSEMBLY.
ASSEMBLY.
Replace the MAIN PWB
ASSEMBLY
ASSEMBLY
Refer to
NO WATER SUPPLY
Check the wiring on the
dispenser.
Put the detergent in the
correct position
LIQUID BLEACH
MAIN WASH
: Detergent
Clean the drawer.
NO WATER SUPPLY
DETERGENT DOES NOT FLOW IN
MAIN
WASH
SOFTENER
LIQUID
BLEACH
BLEACH
21
YES
YES
NO
NO
NO
NO
YES
YES
YES
YES
Wiring diagram
MAX
max
ABNORMAL SOUND
SOFTENER DOES NOT FLOW IN
Fix the bolt tightly.
Replace the STATOR
ASSEMBLY or ROTOR
ASSEMBLY.
ASSEMBLY or ROTOR
ASSEMBLY.
Refer to
NO WATER SUPPLY
Check the wiring on the
dispenser.
dispenser.
Put it in the correct
compartment.
compartment.
Clean the Cap and
Drawer.
Drawer.
Is the motor bolt loosened?
Is there friction noise from the motor?
Is water supplied?
Are receptacles correctly connected to the terminals
of the INLET VALVE ASSEMBLY?
of the INLET VALVE ASSEMBLY?
Is softener put in the correct compartment of the
drawer?
drawer?
Is the softener cap clogged?
22
OPTION
SPIN
NO
YES
YES
YES
YES
NO
NO
NO
NO
YES
YES
NO
PWB ASSEMBLY (Main)
AC 120-127V
(1)
(2)
Replace the
S.PRESSURE SWITCH
ASSEMBLY
S.PRESSURE SWITCH
ASSEMBLY
Replace the MAIN PWB
ASSEMBLY
ASSEMBLY
Repair the DRAIN HOSE
ASSEMBLY.
ASSEMBLY.
Remove foreign material.
Reconnect or repair the
connector
connector
Repair the DRAIN PUMP
ASSEMBLY.
ASSEMBLY.
Repair the MAIN PWB
ASSEMBLY.
ASSEMBLY.
When pressing OPTION and SPIN at the same time
after draining, is the water level frequency 248 ~ 262 or
more?
When pressing SPIN, DRY buttons at the same time
while wash, is the water level frequency between
230 - 243 ?
after draining, is the water level frequency 248 ~ 262 or
more?
When pressing SPIN, DRY buttons at the same time
while wash, is the water level frequency between
230 - 243 ?
Checking voltage between two pins as press the
POWER button is the voltage 120-127V~?
POWER button is the voltage 120-127V~?
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Is the connector disconnected, disassembled?
Is the coil of the drain pump cut-off?
(resistance of coil is 80~150Ω)
When checking voltage between connectors
( , )on spinning, is the voltage 120-127V~
as the figure?
( , )on spinning, is the voltage 120-127V~
as the figure?
HEATING WITHOUT WATER
DRAIN MALFUNCTIONING
23
TEMP.
NO
YES
YES
NO
When checking the voltage between
connector during whites washing. is the
voltage 120-127V?
connector during whites washing. is the
voltage 120-127V?
Replace the MAIN PWB
ASSY
ASSY
YES
NO
After power off and the heater terminal is
disconnected, is the resistance 10~30 ?
disconnected, is the resistance 10~30 ?
When pressing WATER TEMP. during, is the
displayed temperature is over 10ûC
higher than the selected temperature?
displayed temperature is over 10ûC
higher than the selected temperature?
Is the resistance between Thermistor
Comectors 2.5k ~ 180k ?
Comectors 2.5k ~ 180k ?
Replace the
HEATER ASSEMBLY
HEATER ASSEMBLY
Check if inlet hose is
connected to a hot
faucet ; otherwise,
replace PWB
ASSEMBLY(Main)
connected to a hot
faucet ; otherwise,
replace PWB
ASSEMBLY(Main)
Replace Thermister
NO
After power off,is the resistance of wire
(RED-YELLOW) connectors between
10 ~30 ?
(RED-YELLOW) connectors between
10 ~30 ?
Normal
NO
YES
RED
YELLOW
1 2 3
YES
AC 120-127V
(1)
Push the THERMISTOR
tightly to the rubber.
tightly to the rubber.
When checking THERMISTOR on the tub is the
THERMISTOR loosened above 2mm from
the rubber?
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
WASH HEATER TROUBLE
Click on the first or last page to see other WD-3243RHD / WD-3245RHD service manuals if exist.