LG SP105 Service Manual ▷ View online
7
4. PARTS IDENTIFICATION
Drain Hose
Dispenser
Door
Lower Cover Cap
Drain Plug
Drain Pump Filter
Adjustable Feet
Power Plug
Control Panel
Shipping Bolts (4)
Drain
Cold Water Inlet
Hot Water Inlet
Air Vent for Safety
If the supply cord is damaged,
it must be replaced by the
manufacturer or an authorized
service technician in order to
avoid a hazard.
it must be replaced by the
manufacturer or an authorized
service technician in order to
avoid a hazard.
Name:
Front-loading Washing Machine
Power supply:
220V~ 50Hz
)
n
e
p
o
r
o
o
d
h
ti
w
D
(
m
c
1
.
9
2
1
,
)
H
(
m
c
3
.
8
9
X
)
D
(
m
c
6
.
5
7
X
)
W
(
m
c
6
.
8
6
:
e
z
i
S
27 (W) X 29
3/4
(D) X 38
11
/
16
(H), 50
13
/
16
(D with door open)
Weight:
190 lbs. (86 kg)
Wash capacity:
15kg
Spin speed:
1000 rpm max.
Permissible water pressure: 14.5~116 psi (100~800 kPa)
Back of Washer
Specifications subject to change by manufacturer.
Note
Accessories
Hot/Cold (1each)
Hose
Wrench
Tie strap
to secure drain hose to standpipe
inlet hose, or laundry tub
8
5. INSTALLATION INSTRUCTIONS
Unscrew the 4 bolts with the wrench supplied
Take out the 4 bolts by twisting the braces slightly
Take out the 4 bolts by twisting the braces slightly
Keep the 4 bolts and the wrench for future use
(Whenever the appliance is transported, the
shipping bolts and braces must be replaced.)
shipping bolts and braces must be replaced.)
Close the holes with the caps supplied.
The appliance is fitted with shipping bolts to prevent
internal damage during transportation.
Packing and all shipping bolts must be removed
before using the washer.
internal damage during transportation.
Packing and all shipping bolts must be removed
before using the washer.
When unpacking the base, be sure to remove
the additional packing support in the middle of
the base packing.
the additional packing support in the middle of
the base packing.
Shipping bolts
• Washer is heavy. Two or more people may be needed to install and move the appliance.
Failure to do so can result in back or other injury.
• Store and install the washer where it will not be exposed to temperatures below freezing or exposed to
outdoor weather conditions. Failure to follow this warning can cause serious injury, fire, electrical shock, or
death.
death.
• This appliance must be properly grounded for personal safety. Properly ground washer to conform with all
governing codes and ordinances. Failure to follow this warning can cause serious injury, fire, electrical shock,
or death.
or death.
• Do not install the washer in humid spaces to reduce the risk of electric shock. Failure to follow this
warning can cause serious injury, fire, electrical shock or death.
• The base opening must not be obstructed by carpeting when the washer is installed on a carpeted floor.
• Do not remove ground prong. Do not use an adapter or extension cord. Plug into a grounded 3 prong outlet.
Failure to follow this warning can cause serious injury, fire, electrical shock or death.
Removing shipping bolts
Wrench
CAP
!
WARNING
9
Installation clearances
The location must be large enough to open
the washer door completely.
Washer dimensions
The following dimensions shown are for the minimum
spacing allowed.
Additional spacing should be considered for
installation and servicing.
• Additional clearances might be required for wall,
• Additional clearances might be required for wall,
door, and floor moldings.
• Additional spacing of 4 (10 cm) on back,
1 (2.5 cm) on all sides of the washer is
recommended to reduce noise transfer.
Companion appliance spacing should also be
considered.
Minimum installation spacing for
recessed area installation.
Front view
Side view
29
3
/
4
"
(75.6 cm)
4"
(10 cm)
27"
(68.6 cm
)
29
3/4
"
(75.6 cm)
38
11/16
"
(98.3 cm)
50
13/16
"
(129.1 cm
)
27"
(68.6 cm)
1"
(2.5 cm)
1"
(2.5 cm)
10
•
Must be within 60 (1.5 m) of either side of the
washer. Do not overload the outlet with more
than one appliance.
washer. Do not overload the outlet with more
than one appliance.
•
Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation
of the customer to have a proper outlet
installed by a qualified electrician.
installed by a qualified electrician.
Level floor
• Allowable slope under entire washer is 1°.
• To minimize noise and vibration, the washer
• To minimize noise and vibration, the washer
MUST be installed on a solidly constructed
floor.
floor.
• Carpeting and soft tile surfaces are not
recommended.
• Never install the washer on a platform or
weakly supported structure.
NOTE: A firm, solid floor is even more critical to a
front-loading washer than to a top-loader.
If your floor is wood and/or frame
construction, you may need to reinforce it.
Front-loaders use substantially faster spin
speeds than top-loaders, causing greater
vibration. If the floor is not solid, your washer
will vibrate. You will hear and feel the
vibration throughout your house.
If your floor is wood and/or frame
construction, you may need to reinforce it.
Front-loaders use substantially faster spin
speeds than top-loaders, causing greater
vibration. If the floor is not solid, your washer
will vibrate. You will hear and feel the
vibration throughout your house.
solid floor
Connect the power plug to the wall outlet.
Avoid connecting several electric devices, as
doing so may cause a fire.
doing so may cause a fire.
CONNECT POWER PLUG
INSTALL THE APPLIANCE
ON A FLAT AND FIRM SURFACE
Click on the first or last page to see other SP105 service manuals if exist.