LG SP105 Service Manual ▷ View online
24
NO
YES
YES
NO
NO
NO
NO
YES
YES
NO
1
2
3
4
(Yellow 4pin)
Repair the DRAIN HOSE
ASSEMBLY.
ASSEMBLY.
Reconnect or repair the
connector
connector
Replace the DRAIN
PUMP ASSEMBLY.
PUMP ASSEMBLY.
Replace the MAIN PWB
ASSEMBLY.
ASSEMBLY.
Is the drain hose twisted or frozen?
Is the connector disconnected or disassembled?
Is the coil of the drain pump too high or low?
(resistance of the coil is 10-20 Ω)
(resistance of the coil is 10-20 Ω)
When checking voltage between connectors
(
and ) during drain, is the voltage 220 V AC
as in the figure?
OE ERROR (DRAIN TROUBLE)
25
YES
YES
YES
NO
NO
YES
NO
Main washer
softener
Hose
PRESSURE S/W ASSEMBLY
YES
Hose
PRESSURE S/W ASSEMBLY
YES
NO
Replace the INLET
VALVE ASSEMBLY.
VALVE ASSEMBLY.
Make sure the tap is closed
before replacing.
before replacing.
Replace the
PRESSURE S/W
ASSEMBLY.
PRESSURE S/W
ASSEMBLY.
Replace the
PRESSURE S/W
ASSEMBLY.
PRESSURE S/W
ASSEMBLY.
Is resistance between each terminal of INLET
VALVE ASSEMBLY 0.8~1.2kΩ?
VALVE ASSEMBLY 0.8~1.2kΩ?
Is water continuously supplied?
Is PRESSURE S/W ASSEMBLY broken?
Check electrical connection.
Replace the MAIN PWB ASSEMBLY.
Replace the MAIN PWB ASSEMBLY.
Is PRESSURE S/W ASSEMBLY broken?
Check electrical connection.
Replace the MAIN PWB ASSEMBLY.
Replace the MAIN PWB ASSEMBLY.
FE ERROR
PE ERROR (PRESSURE S/W TROUBLE)
26
YES
NO
NO
YES
DOOR S/W
ASSEMBLY
ASSEMBLY
dE ERROR (DOOR ERROR)
Was the load too large?
Is DOOR SWITCH ASSEMBLY broken?
Does the spring of Latch Hook actuate?
Check the DOOR SWITCH
ASSEMBLY Connector and
MAIN PWB ASSEMBLY
(Blue 4 pin , Yellow 4 pin
and white 3 pin connector .
ASSEMBLY Connector and
MAIN PWB ASSEMBLY
(Blue 4 pin , Yellow 4 pin
and white 3 pin connector .
Replace the DOOR
SWITCH ASSEMBLY.
SWITCH ASSEMBLY.
Replace Door Assembly.
1
3
2
27
YES
YES
YES
NO
NO
Have all the transit bolts and base packing
been removed?
been removed?
Remove the transit bolts
and Base packing.
and Base packing.
Move the washer or
reinforce the floor.
reinforce the floor.
Is the washer installed on a solidly constructed
floor?
floor?
Check if the washer is perfectly level as follows:
Check the leveling of the washer with a level
and check that the washer is stable.
and check that the washer is stable.
Put an unbalance part (rubber) inside of drum
and start QC test mode and run in high spin
(Refer to page 17)
When the machine is spinning in high speed,
verify that it is stable.
and start QC test mode and run in high spin
(Refer to page 17)
When the machine is spinning in high speed,
verify that it is stable.
VIBRATION & NOISE IN SPIN
If it is not stable, adjust feet accordingly. After
the washer is level, tighten the lock nuts up
against of the base of the washer. All lock nuts
must be tightened.
the washer is level, tighten the lock nuts up
against of the base of the washer. All lock nuts
must be tightened.
If you do not have the unbalance part, put 4.5 to
6.5 lbs (2 to 3 kg) of clothing.
6.5 lbs (2 to 3 kg) of clothing.
When the machine is spinning at high speed,
verify that it is stable.
verify that it is stable.
Click on the first or last page to see other SP105 service manuals if exist.