LG F1443KDS / F1443KDS7 / F1443KDS9 Service Manual ▷ View online
45
9-4. PUMP MOTOR ASSEMBLY
Wiring
diagram
diagram
Circuit in the MAIN PWB
Wiring Diagram
MICOM
IC
R
5V
Rg
Cg
Vdc
Rs
Cs
PCB
CONNECTOR
PUMP
Vac
2
1
4
3
Pump Driving circuit
MAIN PWB
NA2
1 2 3
1
2
3
3 2 1
3 2 1
3 2 1
1
2
3
4
1 2 3 4
BL3
SB
BK
BN
DRAIN
PUMP
PUMP
Object
Function
Test
points
points
Result
* Each circuits of loads in wiring diagram are all same.
Two pump motors are used to drain the tub and to circulate the water / detergent solution.
Drain Pump
Drain Pump
Test Points
Result
(1) to (2)
10-20
Ω
T.P
For Drain
(1)
(2)
(1)
(2)
46
9-5. INLET VALVE ASSEMBLY
Wiring
diagram
diagram
Circuit in the MAIN PWB
INLET
VALVE
VALVE
Vac
Rs
Vdc
Cg
Rg
IC
MICOM
Cs
PCB
CONNECTOR
Inlet valve driving circuit
Function
Test
points
points
and
Result
Depending on the cycle and water temperature, the controller will energize the hot or cold
water valve solenoids to meet the selected water temperature.
water valve solenoids to meet the selected water temperature.
After pull out the connector of defective valve, check the resistance.
Test points
(1)-(2)
Result
0.8-1.2 k
Ω
Wiring Diagram
MAIN
WASH
PRE
WASH
BLEACH
HOT
VALVE
1
2
1
2
1
2
1
2 RD
BL
BL
NA
WH
NA4
GY VT
BL
NA2
BL3
4
3
2
1
1
2
3
1
2
3
4
3
2
1
4
3
2
1
4
3
2
1
COMMON
(BK)
(BK)
MIAN PWB
INLET VALVE
* Each circuits of loads in wiring diagram are all same.
(1) (2)
(1) (2)
(1) (2)
(1) (2)
47
9. DISASSEMBLY INSTRUCTIONS
Disassemble and repair the parts after pulling out power cord from the outlet.
1 Unscrew the screws on the top plate.
3 The cover(Inner) is disassembled.
2 The plate assembly(Top) is pulled back and
then upward to arrow direction.
1 Pull out the drawer and unscrew 2 screws.
2 Lift the side the Control Panel Assembly and
pull it out
1 Two screws are unscrewed.
2 Push out PANEL ASSEMBLY, CONTROL after
Push the hook below.
1 The PWB assembly(Display) is disconnected.
2 When 7 screws are unscrewed on the PWB
insulator and the PWB assembly(Display) is
disassembled from the PWB insulator.
disassembled from the PWB insulator.
CONTROL PANEL
Screws
Screws
Screws
Disassembly 3 connectors.
48
1 Disassembly lower cover assembly.
2 Two screws are unscrewed.
3 Pull the PWB assembly in direstion of red
arrow.
4 Disassembly PWB like the picture.
PWB ASSEMBLY(MAIN)
1 The plate assembly(Top) are disassembled.
3 Two screws are unscrewed.
3 Two screws are unscrewed.
2 Pull the drawer to arrow direction.
4 Clamp
4 Clamp
5 Cutting cable ties and the ventillation hose
are disassembly on the dispenser
5 Cutting cable ties and the ventillation hose
are disassembly on the dispenser
DISPENSER ASSEMBLY
2 Pull the drawer to arrow direction.
2
1
Click on the first or last page to see other F1443KDS / F1443KDS7 / F1443KDS9 service manuals if exist.