LG DWM1300 Service Manual ▷ View online
20
NO
YES
NO
NO
YES
NO
YES
YES
NO
NO
YES
YES
YES
NO
NO
NO
YES
Wiring diagram
option (HOT)
option (HOT)
MAX
Is the water supply shut-off?
Is the tap opened?
When you press both Option button and Spin
buttons simultaneously, is the water level frequency
below 240?
buttons simultaneously, is the water level frequency
below 240?
Is the inlet valve filter clogged with impurity?
Is resistance of the inlet valve connector
between 2 to 8
between 2 to 8
k
Ω
?
Check the voltage between each terminal of inlet
Valve is 220 - 240V~.
(Refer to 7-2 TEST MODE)
Is water supplied?
Are replaceptacles correctly connected to the
terminals of inlet valve?
terminals of inlet valve?
Is detergent put in the correct compartment of
the drawer?
the drawer?
Is the detergent caked or hardened?
Open the tap.
Check the chamber (Air)
and the tube clogged
with impurity.
and the tube clogged
with impurity.
Clean the filter.
Replace the inlet valve.
Replace PWB assembly
(Main).
(Main).
Refer to solution
NO INLET.
NO INLET.
Check the wiring on the
dispenser.
Put the detergent in the
correct position.
PRE+MAIN
MAIN WASH
: Detergent
Clean the drawer.
NO WATER SUPPLY
DETERGENT DOES NOT FLOW IN
MAIN
WASH
SOFTENER
PRE -
WASH
21
YES
YES
YES
NO
NO
NO
NO
NO
YES
YES
YES
YES
Wiring diagram
option (HOT)
MAX
MAX
max
A B N O R M A L S O U N D
S O F T E N E R D O E S N O T F L O W I N
Fix the bolt tightly.
Replace the V-belt
(4400FR3116A).
(4400FR3116A).
Replace the motor.
Refer to
^NO WATER SUPPLY_
Check the wiring on the
dispenser.
dispenser.
Put it in the correct
compartment.
compartment.
Clean the cap and
drawer.
drawer.
Is the pulley bolt loosened?
Is the belt worn?
Is there friction noise from the motor?
Is water supplied?
Are receptacles correctly connected to the terminals
of inlet valve?
of inlet valve?
Is softener put in the correct compartment of
drawer?
Is the softener cap clogged?
YES
YES
NO
NO
NO
NO
YES
YES
NO
PWB ASSEMBLY (MAIN)
2
1
(5)
(6)
DRAIN MALFUNCTIONING
Repair drain hose.
Remove foreign material.
Reconnect or repair the
connector.
connector.
Replace the pump
assembly.
assembly.
Replace the PWB
assembly (Main) .
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Is the connector disconnected, disassembled?
Is the coil of drain pump cut-off?
(resistance of coil is 90~160
Ω)
When checking voltage between connectors
( , ) on spinning, is the voltage 220 - 240V~
as the figure?
22
AC 220-240V
NO
NO
YES
PWB ASSEMBLY (MAIN)
Spin
Option
Replace the sensor
(pressure).
Replace the PWB
assembly (Main).
assembly (Main).
When pressing [Option] and [Spin] at the same time
after draining, is the water level frequency 252 or
more?
When pressing [Option], [Spin] buttons at the
same time while wash, is the water level
frequency between 220 - 240?
after draining, is the water level frequency 252 or
more?
When pressing [Option], [Spin] buttons at the
same time while wash, is the water level
frequency between 220 - 240?
Checking voltage between two pins as press
the power Button is the voltage 220 - 240V~?
the power Button is the voltage 220 - 240V~?
HEATING WITHOUT WATER
23
When checking the voltage between
connector the PWB assembly (Main)
during whites washing ,Is the voltage
220 - 240V ?
connector the PWB assembly (Main)
during whites washing ,Is the voltage
220 - 240V ?
Replace the PWB
assembly (Main).
assembly (Main).
YES
NO
After power off and the heater terminal is
disconnected, is the resistance 10 to 30 ?
disconnected, is the resistance 10 to 30 ?
Replace the heater
assembly.
assembly.
NO
After power off,is the resistance of wire
(RED-YELLOW) connectors between
10 to 30 ?
(RED-YELLOW) connectors between
10 to 30 ?
Normal.
NO
YES
RED
YELLOW
1
2
4
3
~
220 - 240V~
PWB ASSEMBLY (MAIN)
WASH HEATER TROUBLE
NO
YES
YES
1
2
4
3
(1)
Replace the thermistor
(6322FR2046B)
(6322FR2046B)
Push the thermistor
tightly to the rubber.
When disconnect the connector (1) on the
PWB assembly (Main) is the resistance of the
Natural connectors
PWB assembly (Main) is the resistance of the
Natural connectors
~ ② ( Blue/White, Violet),
③ (Blue, White) ₩between 2.5kΩ to 180kΩ
(105
(105
℃
~0
℃
)?
When checking thermistor on the tub cover,
is the thermistor loosened above 2mm from
the rubber?
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
Click on the first or last page to see other DWM1300 service manuals if exist.