LG DWM1300 Service Manual ▷ View online
28
①
① Take apart the cabinet gasket clamp.
②
②
② Unscrew 2 screws from the cabinet cover.
③
③
③ Open the lower cover cap and unscrew 1 screw inside.
④
④
④ Take apart the lower cover.
①
① Unscrew all the screws on the upper and lower sides of
the cabinet cover.
①
① Take apart the tub gasket clamp.
②
②
② Make sure that the drain hole of the gasket is put
beneath when reassembling the gasket.
※Refer to the arrow mark on the tub cover.
GASKET ASSEMBLY
DOOR
①
① Open the door completely.
②
②
② Remove the two screws from the hinge.
29
①
① Pull out the hinge, pressing its snap.
②
②
② Do not use the pulled out hinge again. It may be taken
off during operation.
1
2
3
Hinge,
Damper
Damper
Damper
PULLEY, MOTOR, DAMPER
(PULLEY)
(MOTOR)
(DAMPER)
Open the lower cover cap (
) by
using coin.
Unplug the drain plug (
) , then
the water flows out,
At this time use a vessel
to prevent water flowing on the floor.
If the water does not flow any
more,turn the pump filter (
At this time use a vessel
to prevent water flowing on the floor.
If the water does not flow any
more,turn the pump filter (
) open
to the left.
Take out any foreign material from
the pump filter (
the pump filter (
). After
cleaning, turn the pump filter(
)
clockwise and insert the
drain plug (
drain plug (
) to the original
place. close the lower cover cap.
Clean the drain pump filter
1
100
3
2
3
2
①
① Remove the back cover.
②
②
② Take off the belt turning the pulley.
③
③
③ Unscrew the bolt to pull out the pulley.
①
① Unscrew 2 screws from the bracket.
②
②
② Push the motor in the arrow direction for disassembling.
③
③
③ When reassembling the motor, make sure that motor
mounting bushings are not taken off from the bracket.
Cap
(Remaining Hose)
Screw
Pump Outlet Hose
Tub Pump Bellows
30
①
① Remove pump outlet hose.
②
②
② Remove tub pump bellows.
③
③
③ Remove cap (remaining hose.)
④
④
④ Disconnect the wiring.
⑤
⑤
⑤ Unscrew 3 screws.
⑥
⑥
⑥ Remove the pump.
①
① Unscrew 3 screws fixing the heater protecting cover.
②
②
② Loosen the M6 heater nut to pull out the heater.
When mounting the heater, be sure to insert the heater
into the heater clip on the bottom of the tub.
①
① Pull it out by holding the thermistor bracket.
If it is pulled by the wire, it may be broken.
②
② When mounting the thermistor again, make sure that it is
got back tight to the rubber.
PUMP
HEATER
THERMISTOR
CAUTION
31
DOOR HINGE ASSEMBLY
SWITCH ASSEMBLY, DOOR LOCK
WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB
①
① Take apart the cabinet cover clamp and release the
gasket.
②
② Unscrew 2 screws holding the door lock.
③
③
③ Disconnect the door lock from the wiring connector.
①
① Disassemble the door from the door hinge.
②
②
② Take apart the cabinet cover clamp and release the
gasket.
③
③ Unscrew 2 screws on the door hinge.
④
④
④ Push the door hinge arm to the inside of the cabinet
cover for disassembling.
①
① Remove the heater.
②
②
② Remove the foreign material (wire, coin and others) by
inserting a long bar through the hole.
Click on the first or last page to see other DWM1300 service manuals if exist.