LG 50PZ950B-SA (CHASSIS:PB12A) Service Manual ▷ View online
- 5 -
4. General Specification
No
Item
Specification
Model
Remark
1.
Receiving System
1) SBTVD / NTSC / PAL-M / PAL-N
PZ950B, PZ570B
2) DVB / NTSC
PZ950E
2.
Available Channel
1) VHF : 02~13
PZ950B, PZ570B
SBTVD
2) UHF : 14~69
3) DTV : 07-69 (VHF high/UHF)
4) CATV : 02~135
1) VHF : 02~13
PZ950E
DVB
2) UHF : 14~69
3) DTV : 14~69
4) CATV : 02~135
3.
Input Voltage
1) AC 100 ~ 240V 50/60Hz
4.
Market
Brazil (Brazil SBTVD Standard)
PZ950B, PZ570B
Colombia, Panama(DVB Standard country)
5.
Screen Size
50 inch Wide(1920 X 1080)
50PZ950, 50PZ570
60 inch Wide(1920 X 1080)
60PZ950, 60PZ570
6.
Aspect Ratio
16:9
7.
Tuning System
FS
8.
Module
PDP50R3 (3D)#### (1920 X 1080)
50PZ950, 50PZ570
PDP60R3 (3D)#### (1920 X 1080)
60PZ950, 60PZ570
9.
Operating Environment
1) Temp : 0 deg ~ 40 deg
2) Humidity : ~ 80 %
10.
Storage Environment
1) Temp : -20 deg ~ 60 deg
2) Humidity : 0 % ~ 90 %
- 6 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet applies to PB12A Chassis applied PDP TV
all models manufactured in TV factory.
all models manufactured in TV factory.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. But it is
flexible when its factory local problem occurs.
(3) The adjustment must be performed in the circumstance of
25
c
C ± 5 cC of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep 100 V - 240 V,
50 / 60 Hz.
(5) Before adjustment, execute Heat-Run for 5 minutes.
V
After Receive 100% Full white pattern (06CH) then
process Heat-run
process Heat-run
(or “8. Test pattern” condition of Ez-Adjust status)
V
How to make set white pattern
1) Press Power ON button of Service Remocon
2) Press ADJ button of Service remocon. Select “10.
2) Press ADJ button of Service remocon. Select “10.
Test pattern” and, after select “White” using
navigation button, and then you can see 100% Full
White pattern.
navigation button, and then you can see 100% Full
White pattern.
* In this status you can maintain Heat-Run useless any
pattern generator
* Notice: if you maintain one picture over 20 minutes
(Especially sharp distinction black with white pattern –
13Ch, or Cross hatch pattern – 09Ch) then it can
appear image stick near black level.
13Ch, or Cross hatch pattern – 09Ch) then it can
appear image stick near black level.
3. Adjustment items
3-1. PCB Assembly adjustment
Caution: Using ‘power on’ button of the control R/C power on
TV
V
MAC Address and Widevine Key Down load
V
ADC Adjustment (manual)
V
DFT Process
V
Insert Tool OPTION (Manual)
V
Insert EDID (Manual)
3-2. Set Assembly Adjustment
V
Power PCB Assembly Voltage adjustment
(Va,Vs voltage adjustment)
V
Adjustment of White Balance
V
Serial number download & Model name D/L
V
Checking the Eye-Q Operation
V
Ping Test
V
LAN port inspection (Ping test)
V
Check Wireless function
V
Magic Motion Remote Controller test
V
3D function test
V
GND and ESD tes
4. PCB Assembly Adjustment
4-1. MAC Address and Widevine Key
Download
* Connect TV SET and PC which download keys Writing
program by RS232C-Cable
(1) Start Program and Click “start” Button to connect TV and
PC.
(2) When download succeed, you can see “OK” on the
screen.
* Each Chassis has it’s own MAC Address. Please be careful
of download.
4-2. ADC Adjustment (Manual)
* GP3 (PB12A) Chassis don’t need Auto ADC adjust process
but, if you need to adjust ADC manually follow this method.
V
Using instrument
1) Adjustment remocon, 801GF(802B, 802F, 802R) or
MSPG925FA pattern generator
(It can output 480i/1080i horizontal 100 % color bar
pattern signal, and its output level must setting
0.7 V ± 0.1 V p-p correctly)
pattern signal, and its output level must setting
0.7 V ± 0.1 V p-p correctly)
< Adjustment pattern : 480i / 1080p 60Hz Pattern >
(1) Adjustment method 480i Comp1, Adjust 1080p
Comp1/RGB (Factory adjustment)
(2) ADC 480i Component1 adjustment
(3) Check connection of Component1
(4) MSPG-925FA -> Model: 209, Pattern 65
(5) Set Component 480i mode and 100% Horizontal Color Bar
(3) Check connection of Component1
(4) MSPG-925FA -> Model: 209, Pattern 65
(5) Set Component 480i mode and 100% Horizontal Color Bar
Pattern(HozTV31Bar), then set TV set to Component1
mode and its screen to “NORMAL”
mode and its screen to “NORMAL”
(6) Check connection both of Component1 and RGB
(7) MSPG-925FA Ë Model: 225, Pattern 65
(8) Set Component 1080p mode and 100% Horizontal Color
(7) MSPG-925FA Ë Model: 225, Pattern 65
(8) Set Component 1080p mode and 100% Horizontal Color
Bar Pattern(HozTV31Bar), then set TV set to Component1
mode and its screen to “NORMAL”
mode and its screen to “NORMAL”
(9) After get each the signal, wait more a second and enter
the “IN-START” with press IN-START key of Service
remocon. After then select “7. External ADC” with
navigator button and press “Enter”.
remocon. After then select “7. External ADC” with
navigator button and press “Enter”.
(10) After then select “23. Auto ADC” and set value “On ->
Off” with navigator button.
(11) Press IN-START Key again.
(12) Select “External ADC” with navigator button and press
(12) Select “External ADC” with navigator button and press
“Enter”
(13) After Then Press key of Service remocon “Right
Arrow(VOL+)”
(14) You can see “ADC Component1 Success”
(15) Component1 1080p, RGB 1080p Adjust is same method.
(16) Component 1080p Adjustment in Component1 input
(15) Component1 1080p, RGB 1080p Adjust is same method.
(16) Component 1080p Adjustment in Component1 input
mode
(17) RGB 1080p adjustment in RGB input mode
(18) If you success RGB 1080p Adjust. You can see “ADC
(18) If you success RGB 1080p Adjust. You can see “ADC
RGB-DTV Success”
4-3. DFT Process.
*
Depend on situation, Step can be changed.
* There are 2 kinds of DFT SEQUENCE FILEs.
O
Applied model list
(1) PB12A_SBTVD : 50/60PZ950B-SA, 50/60PZ570B-SB
(2) PB12A_DVBT : 50/60PZ950E-DA
(2) PB12A_DVBT : 50/60PZ950E-DA
O
Difference between 2 kinds of DFT sequence files.
(1) PB12A_SBTVD file DFT SEQ
- 7 -
No
STEP
1
DFT START
2
[RF]Tool Option Write
3
[RF]RF CHECK
4
[RF]<DTV> Moving Pic Test
5
[COMP1]Color Test
6
[COMP2]Color Test
7
[RGB]Color Test
8
SPDIF OUT Audio Test
9
[RGB]Version Check
10
[RGB]EDID WRITE
11
MOTION REMOCON
12
3D RF EMMITER CHECK
13
[RGB]WIRELESS CHECK
14
LAN PORT CHECK
15
[3D HDMI1] Color Test
16
USB1 AUDIO Test
17
[AV1] Color Test
18
[AV2] Color Test
19
KEY1 Test
20
KEY2 Test
21
[HDMI2] Color Test
22
[HDMI3] Color Test
23
[HDMI4] Color Test
24
USB2 AUDIO Test
25
RF. VOL 30
step(3, "[RF]<NTSC><CH2> Color Test"):check("RF",
color_test, 0.0, -30.0, 30.0,"%")
{
rs232c_tvcontrol("ma 00 02 00 00 00 00 00" ,2000 )
grab_image_check("RF_NTSC.bmp" ,1 ,15000 ,"" )
checkaudio_freq(1 ,1000 ,400 )
work()
grab_image_check("RF_NTSC.bmp" ,1 ,15000 ,"" )
checkaudio_freq(1 ,1000 ,400 )
work()
}
step(4, "[RF] <DTV> Moving Pic Test"):process()
{
{
rs232c_tvcontrol("ma 00 14 00 00 00 03 02" ,2000 )
rs232c_tvcontrol("mc 00 95" ,1000 )
rs232c_tvcontrol("mc 00 95" ,1000 )
waitmessage("1>>DTV,EYE IMAGE/AUDIO CHECK,"
,"WIRE
REMOCON
CHECK-->JACK
INSERT/REMOVED" )
}
(2) PB12A_DVBT file DFT SEQ
4-4. Insert Tool OPTION
and Model Name download.
(1) Press IN_START key on R/C to insert Tool OPTION
(2) On the “ Tool Option ”, Insert Tool Option by a number key
(3) Press the ENTER(
(2) On the “ Tool Option ”, Insert Tool Option by a number key
(3) Press the ENTER(
V
)
(4) Press ENTER(
V
) again.
(5) Select “OK to Download” by using
F
/
G
(VOL +/-) and press
G
(VOL +)
4-5. EDID(The Extended Display
Identification Data) download
(1) Press the ADJ KEY on R/C and enter EZ ADJUST.
(2) Select “5.EDID D/L” by using
(2) Select “5.EDID D/L” by using
D
/
E
(CH +/-) and press
ENTER(
V
).
(3) Select “Start” and press navigation key(
G
).
(4) EDID download is executed automatically.
(5) Press EXIT key on R/C
(5) Press EXIT key on R/C
* Caution
- Never connect HDMI & D-sub Cable when the user
download EDID .
(6) EDID Data ( Model Name = LGTV )
V
HDMI 1 EDID Table (Full HD)
V
HDMI 2 EDID Table (Full HD)
- 8 -
step(3, "[RF]<NTSC><CH4> Color Test"):check("RF",
color_test, 0.0, -30.0, 30.0,"%")
{
rs232c_tvcontrol("ma 00 00 04 00" ,2000 )
grab_image_check("RF_NTSC.bmp" ,1 ,15000 ,"" )
checkaudio_freq(1 ,400 ,400 )
work()
grab_image_check("RF_NTSC.bmp" ,1 ,15000 ,"" )
checkaudio_freq(1 ,400 ,400 )
work()
}
step(4, "[RF] <DTV> Moving Pic Test"):process()
{
step(4, "[RF] <DTV> Moving Pic Test"):process()
{
rs232c_tvcontrol("ma 00 00 01 10" ,1000 )
rs232c_tvcontrol("mc 00 95" ,1000 )
rs232c_tvcontrol("mc 00 95" ,1000 )
waitmessage("1>>DTV,EYE IMAGE/AUDIO CHECK,"
,"WIRE
REMOCON
CHECK-->JACK
INSERT/REMOVED" )
}
Model Name
PZ950B-SA PZ750B-SB PZ570B-SA
Tool Option 1 50 INCH
32777
32809
32777
60 INCH
32781
32813
32781
Tool Option 2 50 INCH
65
65
65
60 INCH
65
65
65
Tool option 3
3551
3295
3551
Tool option 4
7320
7320
7352
Tool option 5
14921
14913
14921
Tool option 6
33625
857
33625
BLOCK(0)
BLOCK(1)
HDMI1
7F
E4
HDMI2
7F
D4
FHD(3D)
HDMI3
7F
C4
HDMI4
7F
B4
RGB
47
Click on the first or last page to see other 50PZ950B-SA (CHASSIS:PB12A) service manuals if exist.