DOWNLOAD LG 42PC55-ZB (CHASSIS:PD73A) Service Manual ↓ Size: 13.57 MB | Pages: 53 in PDF or view online for FREE

- 9 -

V

This AV color balance adjustment should be performed

before white Balance Adjustment.

1) Remote controller for adjustment.
2) MSPG-925FS Pattern Generator (Which has Video Signal:

7 Color Bar Pattern shown in Fig. 3).
- Model: 202 / Pattern: 65  EC and FC model use PAL-
BGDHI. (composite signal)

1) Input the Video signal: 7 color Bar signal into AV3.
2) Set the PSM to Dynamic mode in the Picture menu.
3) Press IN-STAR key on R/C for adjustment.
4) Press the 

G

(Vol. +) key operate to set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

V

This AV color balance adjustment should be performed

before white Balance Adjustment.

1) Remote controller for adjustment.
2) MSPG-925FS Pattern Generator (Which has Video Signal:

7 Color Bar Pattern shown in Fig. 4).
- Model: 215 / Pattern: 65  

1) Input the Component 720p/50Hz 7 Color Bar(MSPG-925FS

model:215, pattern:65) signal into Component.

2) Set the PSM to Dynamic mode in the Picture menu.
3) Press IN-STAR key on R/C for adjustment.
4) Press the 

G

(Vol. +) key operate to set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

V

This AV color balance adjustment should be performed

before white Balance Adjustment.

1) Remote controller for adjustment.
2) MSPG-925FS Pattern Generator (Which has Video Signal:

7 Color Bar Pattern shown in Fig. 5).
- Model: 215 / Pattern: 65  

1) Input the PC 1024x768 @ 60Hz 7 color bar (MSPG-925FS,

Model:3, Pattern: 65) into RGB. (using D-sub to D-sub
cable)

2) Set the PSM to Dynamic mode in the Picture menu.
3) Press IN-STAR key on R/C for adjustment.
4) Press the 

G

(Vol. +) key operate to set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

MSPG925FS

Component

RGB-PC

RF/AV/S-VIDEO

ADC

Model : 3

(1024*768 60Hz)

Pattern : 65

7 Color Bar

Model:215(720P)

Pattern : 65

* 720/50Hz

7 Color Bar

PAL

INPUT SELECT AV3

Model : 202

(PAL-BGDHI)

Pattern : 65

* PAL 7 Color Bar

- System control RS-232 Host should be “PC“ for adjustment.
- Before AV ADC Calibration, execute the “Panel size selection“

(Fig. 4) Color bar Test Pattern

(Fig. 3) Color Balance signal

(Fig. 5) Color bar Test Pattern

- 10 -

V

Before adjusting White-balance , the AV ADC should be

done.

1) Remote controller for adjustment.
2) Color Analyzer.( CA-1000,CA-100+,CA-200 or same

product ) : CH10(PDP)

3) Auto W/B adjustment instrument.(only for Auto adjustment)
4) AV Pattern Generator. 

W 

Synchronization relation between PSM and CSM.

W 

CS-1000/CA-100+/CA-210 White balance adjustment coordinate

and color temperature.

V  

Inside PATTERN is used when W/B is controlled. Connect

to auto controller or push control R/C IN-START -> Enter
the mode of White-Balance, the pattern will come out.

V 

Auto-control interface and directions

1. Adjust in the place where the influx of light like floodlight

around is blocked.(illumination is less than 10ux)

2. Measure and adjust after sticking the Color Analyzer(CA-

100+, CA210) to the side of the module.

3. Aging time : keep white pattern using inside pattern.

W

Auto adjustment Map(RS-232C)

(Manual white Balance)

V  

One of R Gain/ G Gain/ B Gain should be kept on 80, and

others are controlled lowering from 80

(1) ‘power on’ of the control R/C, set heat run to white by

pressing and heat run over 15 minutes. (Set: RS-232 Host:
PC, Baud Rate: 115200bps, Download: Cortez) 

(2) Zero Calibrate CA-100+, and stick the sensor to the center

of PDP module surface when you adjust.

(3) Double click In-start key on Controlling R/C and get in

‘white balance’.

(4) Set test-pattern on and display inside pattern. Control is

carried out on three color temperature, COOL, MEDIUM,
WARM. (Control is carried out three times.)

(5) When the R/G/B GAIN is 80 on OSD, it is the FULL

DYNAMIC Range of the Module. In order to control white
balance without the saturation of FULL DYNAMIC Range
and DATA, one of R Gain / G Gain / B Gain should be kept
on 80, and other two is controlled lowering from 80.

* Color Temperature: Cool, Medium, Warm

(1) When R GAIN is set to 80

- Control G GAIN and B GAIN by lowering from 80. 

(2) When B GAIN is set to 80

- Control R GAIN and G GAIN by lowering from 80.

(3) When G GAIN is set to 80
- Control R GAIN and B GAIN by lowering from 80.

One of R Gain / G Gain / B Gain should be kept on 80, and
adjust other two lower than 80.
(When R/G/B GAIN are all 80, it is the FULL DYNAMIC
Range of Module) 

(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern

Full White Pattern

RS-232C Communication

CA-210

Color

ANALYZER

TYPE : CA-210

Type

Baud Rate

115200

Index

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Data bit

8

Cmd1 Cmd2

j

a

j

b

j

c

j

d

j

e

j

f

Stop bit

1

Parity

NONE

PD73A

Protocol

Setting

Data

Min Value

00(00)

00(00)

00(00)

00(00)

00(00)

00(00)

Max Value

128(80)

128(80)

128(80)

128(80)

128(80)

128(80)

Color Coordinate

x

y 

0.283±0.002

0.293±0.002

0.329±0.002

11000K

9300K

6500K

0.000

0.000

0.003

0.276±0.002

0.285±0.002

0.313±0.002

COOL

MEDIUM

WARM

Mode

Temp

uv

PLASMA

Remark

11000K

9300K

6500K

Cool

Normal

Warm

CSM

- 11 -

CMD

: A0h 

LENGTH : 85~94h (1~16 bytes)
ADH

: E

2

PROM Sub Address high (00~1F)

ADL

: E

2

PROM Sub Address low  (00~FF)

Data

: Write data

CS

: CMD + LENGTH + ADH + ADL + Data_1 + ... + Data_n

Delay

: 20ms

* Description

FOS Default write : <7mode data> write
Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0, Phase
Data write : Model Name and Serial Number write in EEPROM,.

(1) Serial number D/L is using of scan equipment.
(2) Setting of scan equipment operated by Manufacturing

Technology Group.

(3) Serial number D/L must be conformed when it is produced

in production line, because serial number D/L is mandatory
by D-book 4.0.

(Setting: Press ADJ Key in the Adjust remocon)

(1) Select  “System Control 2” by using 

D 

/ 

E

(CH+/-) key, and

press 

V 

(ENTER) Using Adjust remocon, RS-232 Host &

Baud Rate & Download value change)

(1) Select the STATION-> Diagno stics -> To set.

CMD LENGTH ADH ADL DATA_1

DATA_n

...

CS

DELAY

Model

Name

42PC55-ZB

50PC55-ZB

50PB65-ZA

Tool

Option1

2048

2052

2244

1697

1953

1977

0

0

0

14

14

14

2

2

2

1

1

1

192

192

192

Tool

Option2

Area

Option

Option1 Option2 Option3 Option3

No

1

EEPROM WRITE A0h

84h+n

n-byted Write

(n=1~16)

Adjust mode

CMD(hex) LENGTH(hex)

Description

(Fig. 7) Default on OSD

<Component>

<RGB>

<AV>

(Fig. 8) Default on OSD

- 12 -

(2) Check the Serial Number.

1) Push the IN-START key in a Adjust Remocon.
2) Input the Option Number that was specified in the BOM, into

the Shipping area.

3) The work is finished, Push 

V

Key.

1) Extract to folder IDS_Setup.ZIP.

2) Install LGIDS-1

1. After Click the ‘NEXT’ icon, Installation is finished. 

3) Install LGIDS-2

1. You can find the ICON on C:\Program Files\LGIDS. 

1)  Prepare  a  Batch  File(*.txt),  RAM  File(*.hex)  on

C:\Program Files\LGIDS\files. 

* In the TEXT FILE

2) Connect RS232 cable and turn on the power.

(Use the general RS-232C Serial Cable)