JBL PULSE (serv.man6) EMC - CB Certificate ▷ View online
- Page 4 of 8 -
www.nemko.com
Report No. 241619
Clause
Requirement - Test
Result - Remark
Verdict
2.6.5.4
Replace 1st sentence with the following.
Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later
than the supply connections in each of the
following:
Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later
than the supply connections in each of the
following:
Class III equipment.
N/A
2.6.5.8A
Add the following new clause. after 2.6.5.8A
2.6.5.8A Earthing of CLASS 0I EQUIPMENT Plugs
with a lead wire for earthing shall not be used for
equipment having a rated voltage exceeding 150V.
For plugs with a lead wire for earthing, the lead
wire shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with an
earthing terminal or lead wire for earthing in the
external location where easily visible.
2.6.5.8A Earthing of CLASS 0I EQUIPMENT Plugs
with a lead wire for earthing shall not be used for
equipment having a rated voltage exceeding 150V.
For plugs with a lead wire for earthing, the lead
wire shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with an
earthing terminal or lead wire for earthing in the
external location where easily visible.
Class III equipment.
N/A
3.2.3
Add the following after Table 3A:
Table 3A applies when cables complying JIS C
3662 or JIS C 3663 are used. In case of other
cables, cable entries shall be so designed that a
conduit suitable for the cable used can be fitted.
Table 3A applies when cables complying JIS C
3662 or JIS C 3663 are used. In case of other
cables, cable entries shall be so designed that a
conduit suitable for the cable used can be fitted.
Class III equipment.
N/A
3.2.5.1
Add the following to the last of first dashed
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Add the following to the last of second dashed
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Delete 1) in Table 3B
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Add the following to the last of second dashed
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Delete 1) in Table 3B
Class III equipment.
N/A
3.3.4
Add the following note to Table 3D:
Note For cables other than those complying with
JIS C 3662 or JIS C 3663, terminals shall be
suitable for the size of the intended cables.
Note For cables other than those complying with
JIS C 3662 or JIS C 3663, terminals shall be
suitable for the size of the intended cables.
Class III equipment.
N/A
3.3.7
Add the following after the first sentence:
This requirement is not applicable to the external
earthing terminal of Class 0I equipment.
This requirement is not applicable to the external
earthing terminal of Class 0I equipment.
Class III equipment.
N/A
4.3.4
Add the following after the first sentence:
This requirement also applies to those connections
in Class 0I equipment, where CLEARANCE or
CREEPAGE DISTANCES over BASIC
INSULATION would be reduced to less than the
values specified in 2.10.
This requirement also applies to those connections
in Class 0I equipment, where CLEARANCE or
CREEPAGE DISTANCES over BASIC
INSULATION would be reduced to less than the
values specified in 2.10.
Class III equipment.
N/A
- Page 5 of 8 -
www.nemko.com
Report No. 241619
Clause
Requirement - Test
Result - Remark
Verdict
5.1.3
Add a note after the first paragraph as follows:
Note – Attention should be drawn to that majority of
three-phase power system in Japan is of delta
connection, and therefore, in that case, test is
conducted using the test circuit from IEC 60990,
figure 13.
Note – Attention should be drawn to that majority of
three-phase power system in Japan is of delta
connection, and therefore, in that case, test is
conducted using the test circuit from IEC 60990,
figure 13.
Class III equipment.
N/A
5.1.6
Replacement: Replace Table 5A.
7.2
Add the following after the paragraph:
However, the separation requirements and tests of
6.2.1 a), b) and c) do not apply to a CABLE
DISTRIBUTION SYSTEM if all of the following
apply:
− the circuit under consideration is a TNV-1
CIRCUIT; and
– the common or earthed side of the circuit is
connected to the screen of the coaxial cable and to
all accessible parts and circuits (SELV, accessible
metal parts and LIMITED CURRENT CIRCUITS, if
any); and
– the screen of the coaxial cable is intended to be
connected to earth in the building installation.
However, the separation requirements and tests of
6.2.1 a), b) and c) do not apply to a CABLE
DISTRIBUTION SYSTEM if all of the following
apply:
− the circuit under consideration is a TNV-1
CIRCUIT; and
– the common or earthed side of the circuit is
connected to the screen of the coaxial cable and to
all accessible parts and circuits (SELV, accessible
metal parts and LIMITED CURRENT CIRCUITS, if
any); and
– the screen of the coaxial cable is intended to be
connected to earth in the building installation.
No CDS and TNV circuit.
N/A
- Page 6 of 8 -
www.nemko.com
Report No. 241619
Clause
Requirement - Test
Result - Remark
Verdict
W.1
Replace second and third sentence in the first
paragraph with the following:
This distinction between earthed and unearthed
(floating) circuit is not the same as between CLASS
I EQUIPMENT, CLASS 0I EQUIPMENT and
CLASS II EQUIPMENT. Floating circuits can exist
in CLASS I EQUIPMENT or CLASS 0I
EQUIPMENT and earthed circuits in CLASS II
EQUIPMENT.
paragraph with the following:
This distinction between earthed and unearthed
(floating) circuit is not the same as between CLASS
I EQUIPMENT, CLASS 0I EQUIPMENT and
CLASS II EQUIPMENT. Floating circuits can exist
in CLASS I EQUIPMENT or CLASS 0I
EQUIPMENT and earthed circuits in CLASS II
EQUIPMENT.
Class III equipment.
N/A
Annex JA
Addition: Add a new annex with the following
contents.
contents.
Annex JA (normative) Document shredding
machines
Document shredding machines shall also comply
with the requirements of this annex except those of
STATIONARY EQUIPMENT used by connecting
directly to an AC MAINS SUPPLY of three-phase
200V or more.
with the requirements of this annex except those of
STATIONARY EQUIPMENT used by connecting
directly to an AC MAINS SUPPLY of three-phase
200V or more.
Not Document shredding
machines.
machines.
N/A
JA.1
Markings and instructions In the easily visible part
near the document-slot, by a method capable to
make out clearly and not easily disappeared, and
by easily understandable wording, shall indicate the
symbol of;
near the document-slot, by a method capable to
make out clearly and not easily disappeared, and
by easily understandable wording, shall indicate the
symbol of;
and, also the following precautions for use;
- that use by an infant/child may cause a hazard of
injury etc.;
- that a hand can be drawn into the mechanical
section for shredding when touching the document-
slot;
- that clothes can be drawn into the mechanical
section for shredding when touching the document-
slot;
- that hairs can be drawn into the mechanical
section for shredding when touching the document-
slot;
in case of equipment incorporating a commutator
motor, that equipment may catch fire or explode by
spraying of flammable gas.
- that use by an infant/child may cause a hazard of
injury etc.;
- that a hand can be drawn into the mechanical
section for shredding when touching the document-
slot;
- that clothes can be drawn into the mechanical
section for shredding when touching the document-
slot;
- that hairs can be drawn into the mechanical
section for shredding when touching the document-
slot;
in case of equipment incorporating a commutator
motor, that equipment may catch fire or explode by
spraying of flammable gas.
Not Document shredding
machines.
machines.
N/A
- Page 7 of 8 -
www.nemko.com
Report No. 241619
Clause
Requirement - Test
Result - Remark
Verdict
JA.2
Inadvertent reactivation
Any safety interlock which can be operated by
means of the test finger, Figure JA.1, is considered
to cause reactivation of the hazard.
Compliance is checked by inspection and, where
necessary, by a test with the test finger, Figure
JA.1.
means of the test finger, Figure JA.1, is considered
to cause reactivation of the hazard.
Compliance is checked by inspection and, where
necessary, by a test with the test finger, Figure
JA.1.
Not Document shredding
machines.
machines.
N/A
JA.3
Isolating switch
Document shredding machines shall incorporate an
isolating switch complying with sub-clause 3.4.2 as
the device disconnecting the power of hazardous
moving parts. For this switch, two-position (single-
use) switch or multi-position (multifunction) switch
(e.g., slide switch) may be used.
If two-position switch, the positions for “ON” and
“OFF” shall be indicated in accordance with sub-
clause 1.7.8. If multi-position switch, the position for
“OFF” shall be indicated in accordance with sub-
clause 1.7.8 and other positions shall be indicated
with proper terms or symbols.
Compliance is checked by inspection.
isolating switch complying with sub-clause 3.4.2 as
the device disconnecting the power of hazardous
moving parts. For this switch, two-position (single-
use) switch or multi-position (multifunction) switch
(e.g., slide switch) may be used.
If two-position switch, the positions for “ON” and
“OFF” shall be indicated in accordance with sub-
clause 1.7.8. If multi-position switch, the position for
“OFF” shall be indicated in accordance with sub-
clause 1.7.8 and other positions shall be indicated
with proper terms or symbols.
Compliance is checked by inspection.
Not Document shredding
machines.
machines.
N/A
JA.4
Protection in operator access areas
Any warning shall not be used instead of the
structure for preventing access to hazardous
moving parts. Document shredding machines shall
comply with the following requirements.
Push the test finger, Figure JA.1, into all openings
in MECHANICAL ENCLOSURES without applying
additional force. It shall not be possible to touch
hazardous moving parts with the test finger. The
document shredding machine is installed as
intended, and all face of MECHANICAL
ENCLOSURES are subjected to this test. Before
testing with the test finger, remove the parts
detachable without a tool.
Push the wedge-probe, Figure JA.2, into the
document-slot. And, against all directions of
openings, if straight-cutting type, a force of 45 N
shall apply to the probe, and 90 N if cross-cutting
type. In this case, the weight of the probe shall not
influence the test. Before testing withy the test
finger, remove the parts detachable without a tool.
It shall not be possible to touch any hazardous
moving parts, including the shredding roller or the
mechanical section for shedding, with the probe.
structure for preventing access to hazardous
moving parts. Document shredding machines shall
comply with the following requirements.
Push the test finger, Figure JA.1, into all openings
in MECHANICAL ENCLOSURES without applying
additional force. It shall not be possible to touch
hazardous moving parts with the test finger. The
document shredding machine is installed as
intended, and all face of MECHANICAL
ENCLOSURES are subjected to this test. Before
testing with the test finger, remove the parts
detachable without a tool.
Push the wedge-probe, Figure JA.2, into the
document-slot. And, against all directions of
openings, if straight-cutting type, a force of 45 N
shall apply to the probe, and 90 N if cross-cutting
type. In this case, the weight of the probe shall not
influence the test. Before testing withy the test
finger, remove the parts detachable without a tool.
It shall not be possible to touch any hazardous
moving parts, including the shredding roller or the
mechanical section for shedding, with the probe.
Not Document shredding
machines.
machines.
N/A
Click on the first or last page to see other PULSE (serv.man6) service manuals if exist.