JBL ON STAGE 200ID EMC - CB Certificate ▷ View online
- Page 36 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
G.4.3
Combination of transients
N
G.4.4
Transients from cable distribution systems
N
G.5
Measurement of transient voltages (V)
N
a) Transients from a mains supply
N
For an a.c. mains supply
N
For a d.c. mains supply
N
b) Transients from a telecommunication network
N
G.6
Determination of minimum clearances .................:
N
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
P
Metal(s)
used
........................................................: Considered.
⎯
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8)
N
K.1
Making and breaking capacity
No thermal control.
N
K.2
Thermostat reliability; operating voltage (V) ........:
N
K.3
Thermostat endurance test; operating voltage (V)
...............................................................................:
N
K.4
Temperature limiter endurance; operating voltage (V)
...............................................................................:
N
K.5
Thermal cut-out reliability
N
K.6
Stability of operation
N
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
N
L.1
Typewriters
Not used.
N
L.2
Adding machines and cash registers
N
L.3 Erasers
N
L.4 Pencil
sharpeners
N
L.5
Duplicators and copy machines
N
- Page 37 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
L.6 Motor-operated
files
N
L.7
Other business equipment
N
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N
M.1
Introduction
No telephone ringing signal.
N
M.2
Method A
N
M.3 Method
B
N
M.3.1 Ringing
signal
N
M.3.1.1 Frequency
(Hz) .....................................................:
⎯
M.3.1.2 Voltage (V) ...........................................................:
⎯
M.3.1.3 Cadence;
time
(s), voltage (V) .............................:
⎯
M.3.1.4 Single
fault
current (mA) ......................................:
⎯
M.3.2
Tripping device and monitoring voltage ...............:
N
M.3.2.1 Conditions for use of a tripping device or a
monitoring voltage
N
M.3.2.2 Tripping
device
N
M.3.2.3 Monitoring
voltage (V) ..........................................:
N
N
ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9, 6.2.2.1,
7.3.2, 7.4.3 and Clause G.5)
7.3.2, 7.4.3 and Clause G.5)
N
N.1
ITU-T impulse test generators
The impulse test generator
not used.
not used.
N
N.2
IEC 60065 impulse test generator
N
P
ANNEX P, NORMATIVE REFERENCES
⎯
- Page 38 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
Q
ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1)
N
a) Preferred climatic categories ........................... :
No VDR used in equipment.
N
b) Maximum continuous voltage .......................... : N
c) Pulse current .................................................... : N
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
PROGRAMMES
N
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6.2)
coated printed boards (see 2.10.6.2)
The quality control
programmes are not used.
programmes are not used.
N
R.2
Reduced clearances (see 2.10.3)
N
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N
S.1
Test equipment
The impulse testing is not
used.
used.
N
S.2 Test
procedure
N
S.3
Examples of waveforms during impulse testing
N
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
(see 1.1.2)
P
Considered.
⎯
U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
INSULATION (see 2.10.5.4)
N
⎯
- Page 39 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N
V.1 Introduction
N
V.2
TN power distribution systems
N
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N
W.1
Touch current from electronic circuits
Not connected to TNV circuit.
N
W.1.1 Floating
circuits
N
W.1.2 Earthed
circuits
N
W.2
Interconnection of several equipments
N
W.2.1 Isolation
N
W.2.2
Common return, isolated from earth
N
W.2.3
Common return, connected to protective earth
N
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause
C.1)
C.1)
N
X.1
Determination of maximum input current
N
X.2
Overload test procedure
N
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N
Y.1 Test
apparatus ..................................................... :
No ultraviolet light.
N
Y.2
Mounting of test samples ..................................... :
N
Y.3 Carbon-arc
light-exposure apparatus .................. :
N
Y.4
Xenon-arc light exposure apparatus .................... :
N
Z
ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2)
⎯
AA
ANNEX AA, MANDREL TEST (see 2.10.5.8)
⎯
BB
ANNEX BB, CHANGES IN THE SECOND EDITION
⎯
Click on the first or last page to see other ON STAGE 200ID service manuals if exist.