DOWNLOAD JBL ON BEAT Service Manual ↓ Size: 2.02 MB | Pages: 82 in PDF or view online for FREE

Page 4 of 39

Report Ref. No. 086-2101101501-000

TRF No.: IEC/EN60950_1c

Test item particulars ............................................. :

System Speaker

Equipment mobility ................................................. :  [X] movable     [] hand-held       [] transportable

[] stationary  [] for building-in  [] direct plug-in

Connection to the mains ......................................... :  [] pluggable equipment   [] type A   [] type B

[] permanent connection
[] detachable power supply cord
[] non-detachable power supply cord
[X] not directly connected to the mains

Operating condition ................................................. :  [X] continuous

[] rated operating / resting time:

Access location  ...................................................... :  [X] operator accessible

[] restricted access location

Over voltage category (OVC)  ................................. :  [] OVC I     [] OVC II     [] OVC III     [] OVC IV

[] other:

Mains supply tolerance (%) or absolute mains supply
values  .................................................................... :

N/A

Tested for IT power systems  .................................. :  [] Yes     [X] No

IT testing, phase-phase voltage (V)  ........................ :  N/A

Class of equipment  ................................................ :  [] Class I     [] Class II     [X] Class III

[] Not classified

Considered current rating (A)  ................................. :  N/A

Pollution degree (PD)  ............................................. :  [] PD 1     [X] PD 2     [] PD 3

IP protection class .................................................. :  Ordinary

Altitude during operation (m)  .................................. :  Up to 2000

Altitude of test laboratory (m)  ................................. :  Below 2000

Mass of equipment (kg) .......................................... :  Approx. 0.9kg

- test case does not apply to the test object .............. : N/A

- test object does meet the requirement ................... : P (Pass)

- test object does not meet the requirement ............. : F (Fail)

Testing  ................................................................... :

Date of  receipt of  test item ....................................... : 2011-01-28

Date(s) of  performance of  tests ................................ : 2011-01-28 to 2011-02-16

Page 5 of 39

Report Ref. No. 086-2101101501-000

TRF No.: IEC/EN60950_1c

The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.

Throughout this report a point is used as the decimal separator.

Attachments:

- 

33 pages of national deviations and group differences

-  4 pages circuit diagram
- 

5 pages of photo documentation

General product information:

The equipment under test is a Class III System Speaker with docking station for iPod or iPhone. The
speaker is equipped with stereo speakers and provided with remote control. A separated certified external
AC/DC adaptor complied with limited power sources according to IEC/EN 60950-1 should be used.

The speaker contains only secondary (SELV) circuit and the maximum ambient temperature is 40 C.

Page 6 of 39

Report Ref. No. 086-2101101501-000

TRF No.: IEC/EN60950_1c

1

GENERAL

P

1.5

Components

P

1.5.1

General

P

Comply with IEC 60950-1 or relevant component
standard

Components which were
found to affect safety
aspects comply with the
requirements of this standard
or within the safety aspects
of the relevant IEC
component standards (see
appended table 1.5.1)

P

1.5.2

Evaluation and testing of components

Components which are
certified to IEC and/or
national standards are used
correctly within their ratings.
Components not covered by
IEC standards are tested
under the conditions present
in the equipment.

P

1.5.3

Thermal controls

No thermal control.

N/A

1.5.4

Transformers

No isolating transformer in
the equipment.

N/A

1.5.5

Interconnecting cables

Class III equipment.

N/A

1.5.6

Capacitors bridging insulation

Class III equipment.

N/A

1.5.7

Resistors bridging insulation

Class III equipment.

N/A

1.5.7.1

Resistors bridging functional, basic or
supplementary insulation

N/A

1.5.7.2

Resistors bridging double or reinforced insulation
between a.c. mains and other circuits

N/A

1.5.7.3

Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable

N/A

1.5.8

Components in equipment for IT power systems

Class III equipment.

N/A

1.5.9

Surge suppressors

Class III equipment.

N/A

1.5.9.1

General

N/A

1.5.9.2

Protection of VDRs

N/A

1.5.9.3

Bridging of functional insulation by a VDR

N/A

1.5.9.4

Bridging of basic insulation by a VDR

N/A

1.5.9.5

Bridging of supplementary, double or reinforced
insulation by a VDR

N/A

1.6

Power interface

P

1.6.1

AC power distribution systems

DC supplied.

N/A

1.6.2

Input current

(see appended table 1.6.2)

P

Page 7 of 39

Report Ref. No. 086-2101101501-000

TRF No.: IEC/EN60950_1c

1.6.3

Voltage limit of hand-held equipment

This appliance is not a
handheld equipment.

N/A

1.6.4

Neutral conductor

Class III equipment.

N/A

1.7

Marking and instructions

P

1.7.1

Power rating

See below

P

Rated voltage(s) or voltage range(s) (V)  ............. : 13VDC

P

Symbol for nature of supply, for d.c. only ............. :

IEC 60417, symbol No.
5031, is used.

P

Rated frequency or rated frequency range (Hz)  .. :

DC supplied.

N/A

Rated current (mA or A)  ..................................... : 2.5A

P

Manufacturer’s name or trade-mark or
identification mark  .............................................. :

P

Model identification or type reference  ................. : JBL OnBeat

P

Symbol for Class II equipment only  .................... : Class III equipment.

N/A

Other markings and symbols  .............................. : Additional symbols or

markings that do not give
rise to misunderstand.

P

1.7.2

Safety instructions and marking

Safety instructions in
English and German.
Other languages will be
provided separately when
submitted for national
approval.

P

1.7.2.1

General

Considered.

P

1.7.2.2

Disconnect devices

Class III equipment.

P

1.7.2.3

Overcurrent protective device

Class III equipment.

N/A

1.7.2.4

IT power distribution systems

Class III equipment.

N/A

1.7.2.5

Operator access with a tool

Class III equipment.

P

1.7.2.6

Ozone

N/A

1.7.3

Short duty cycles

Equipment is designed for
continuous operation.

N/A

1.7.4

Supply voltage adjustment  ................................ :  No voltage/frequency

setting.

N/A

Methods and means of adjustment; reference to
installation instructions  ...................................... :

N/A

1.7.5

Power outlets on the equipment  ......................... :  No outlet provided.

N/A

1.7.6

Fuse identification (marking, special fusing
characteristics, cross-reference)  ........................ :

No fuse

N/A

1.7.7

Wiring terminals

N/A

1.7.7.1

Protective earthing and bonding terminals  ......... :  Class III equipment.

N/A

1.7.7.2

Terminals for a.c. mains supply conductors

Class III equipment.

N/A

1.7.7.3

Terminals for d.c. mains supply conductors

Class III equipment.

N/A