JBL ON BEAT EMC - CB Certificate ▷ View online
Page 16 of 39
Report Ref. No. 086-2101101501-000
TRF No.: IEC/EN60950_1c
3.3.5
Wiring terminal sizes
N/A
Rated current (A), type, nominal thread diameter
(mm) .................................................................. :
(mm) .................................................................. :
3.3.6
Wiring terminal design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
N/A
3.4.1
General requirement
No mains connection
N/A
3.4.2
Disconnect devices
N/A
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Number of poles - single-phase and d.c.
equipment
equipment
N/A
3.4.7
Number of poles - three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
N/A
3.5
Interconnection of equipment
P
3.5.1
General requirements
Considered.
P
3.5.2
Types of interconnection circuits ......................... : Interconnection circuits of
SELV only
P
3.5.3
ELV circuits as interconnection circuits
No ELV interconnection
circuits.
circuits.
N/A
3.5.4
Data ports for additional equipment
Class III equipment.
N/A
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
N/A
Angle of 10
EUT < 7kg
N/A
Test force (N) ..................................................... : Equipment is not a
floorstanding unit.
N/A
4.2
Mechanical strength
N/A
4.2.1
General
Class III equipment, no
hazardous parts inside.
hazardous parts inside.
N/A
4.2.2
Steady force test, 10 N
Class III equipment, no
hazardous parts inside.
hazardous parts inside.
N/A
Page 17 of 39
Report Ref. No. 086-2101101501-000
TRF No.: IEC/EN60950_1c
4.2.3
Steady force test, 30 N
Class III equipment, no
hazardous parts inside.
hazardous parts inside.
N/A
4.2.4
Steady force test, 250 N
Class III equipment, no
hazardous parts inside.
hazardous parts inside.
N/A
4.2.5
Impact test
N/A
Fall test
Class III equipment, SELV
circuit only.
circuit only.
N/A
Swing test
Class III equipment, SELV
circuit only.
circuit only.
N/A
4.2.6
Drop test; height (mm) ........................................ : Drop test not applicable.
N/A
4.2.7
Stress relief test
Class III equipment.
N/A
4.2.8
Cathode ray tubes
No cathode ray tube.
N/A
Picture tube separately certified .......................... :
—
4.2.9
High pressure lamps
No high pressure lamp.
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) ..... :
Not wall or ceiling mounted
equipment.
equipment.
N/A
4.3
Design and construction
P
4.3.1
Edges and corners
All edges and corners are
rounded and/or smoothed.
rounded and/or smoothed.
P
4.3.2
Handles and manual controls; force (N) ............ :
No handles or manual
controls.
controls.
N/A
4.3.3
Adjustable controls
No control devices.
N/A
4.3.4
Securing of parts
Class III equipment.
N/A
4.3.5
Connection by plugs and sockets
SELV connectors do not
comply with IEC 60320 or
IEC 60083.
comply with IEC 60320 or
IEC 60083.
P
4.3.6
Direct plug-in equipment
Not intended to plug directly
into a wall socket-outlet.
into a wall socket-outlet.
N/A
Torque ............................................................... :
Compliance with the relevant mains plug standard
........................................................................... :
........................................................................... :
4.3.7
Heating elements in earthed equipment
No heating elements.
N/A
4.3.8
Batteries
Only button cell battery
provided for remote control
provided for remote control
P
- Overcharging of a rechargeable battery
No such battery
N/A
- Unintentional charging of a non-rechargeable
battery
battery
N/A
- Reverse charging of a rechargeable battery
N/A
- Excessive discharging rate for any battery
N/A
4.3.9
Oil and grease
No oil and grease.
N/A
Page 18 of 39
Report Ref. No. 086-2101101501-000
TRF No.: IEC/EN60950_1c
4.3.10
Dust, powders, liquids and gases
The equipment does not
generate ionizing radiation
or use a laser, and does not
contain flammable liquids or
gases.
generate ionizing radiation
or use a laser, and does not
contain flammable liquids or
gases.
N/A
4.3.11
Containers for liquids or gases
No containers for liquids or
gases in the equipment.
gases in the equipment.
N/A
4.3.12
Flammable liquids ............................................. : The equipment does not
contain flammable liquid.
N/A
Quantity of liquid (l) ........................................... :
—
Flash point ( C) ................................................. :
—
4.3.13
Radiation
No ionizing radiation, laser
or flammable gases
presents.
or flammable gases
presents.
N/A
4.3.13.1
General
N/A
4.3.13.2
Ionizing radiation
N/A
Measured radiation (pA/kg) ................................ :
Measured high-voltage (kV) ............................... :
Measured focus voltage (kV) ............................. :
CRT markings ................................................... :
4.3.13.3
Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification ...................................................... :
classification ...................................................... :
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation .... :
N/A
4.3.13.5
Laser (including LEDs)
N/A
Laser class ........................................................ :
4.3.13.6
Other types ........................................................ :
N/A
4.4
Protection against hazardous moving parts
N/A
4.4.1
General
No hazardous moving parts
N/A
4.4.2
Protection in operator access areas ................... :
N/A
4.4.3
Protection in restricted access locations ............ :
N/A
4.4.4
Protection in service access areas
N/A
4.5
Thermal requirements
P
4.5.1
General
No exceeding temperature.
P
4.5.2
Temperature tests
(see appended table 4.5).
P
Normal load condition per Annex L .................... :
4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
(see appended table 4.5)
P
Page 19 of 39
Report Ref. No. 086-2101101501-000
TRF No.: IEC/EN60950_1c
4.5.5
Resistance to abnormal heat ............................. : No thermoplastic parts
carrying hazardous
voltages.
voltages.
N/A
4.6
Openings in enclosures
N/A
4.6.1
Top and side openings
No openings, no hazard
N/A
Dimensions (mm) .............................................. :
4.6.2
Bottoms of fire enclosures
No fire enclosure
N/A
Construction of the bottomm, dimensions (mm) . :
4.6.3
Doors or covers in fire enclosures
N/A
4.6.4
Openings in transportable equipment
N/A
4.6.4.1
Constructional design measures
N/A
Dimensions (mm) .............................................. :
4.6.4.2
Evaluation measures for larger openings
N/A
4.6.4.3
Use of metallized parts
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature ( C), time (weeks) ...... :
4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of flame
Method 1 is used.
P
Method 1, selection and application of components
wiring and materials
wiring and materials
Equipment is class III
equipment, powered by
separately certified LPS
adaptor
equipment, powered by
separately certified LPS
adaptor
P
Method 2, application of all of simulated fault
condition tests
condition tests
N/A
4.7.2
Conditions for a fire enclosure
See below.
P
4.7.2.1
Parts requiring a fire enclosure
Refer to cl. 4.7.2.2
N/A
4.7.2.2
Parts not requiring a fire enclosure
Fire enclosure is not
required, class III equipment
supplied by Limited Power
Source. Components
mounted on material of min.
V-1 material.
required, class III equipment
supplied by Limited Power
Source. Components
mounted on material of min.
V-1 material.
P
4.7.3
Materials
P
4.7.3.1
General
Components and materials
have adequate flammability
classification. (see
appended table 1.5.1)
have adequate flammability
classification. (see
appended table 1.5.1)
P
4.7.3.2
Materials for fire enclosures
Fire enclosure is not
required, class III equipment
supplied by Limited Power
Source. Components
mounted on material of min.
V-1 material.
required, class III equipment
supplied by Limited Power
Source. Components
mounted on material of min.
V-1 material.
N/A
Click on the first or last page to see other ON BEAT service manuals if exist.