JBL ON BEAT XTREME Service Manual ▷ View online
11.05.31
11.05.31
11.05.31
2405SCLZ
JBL® OnBeat Xtreme™
5
5
J.K Han Y.J Jung J.K Park
SHEET05 (KEY)
A
B
C
D
1
2
3
4
5
6
D
C
B
A
DESIGN
APPROVE
SHEET
CHECK
REVISION
1
2
3
3
4
5
5
6
7
7
1
1
DESIGN
KEY0
KEY1
KEY2
GND
LED0
KEY/LED PCB
POWER ON
STANDBY
SOURCE
LED1
LED2
LED3
LED4
ON/STBY
VOL+
VOL-
MULTIFUNCTION
SOURCE
SW01
TACT
SW04
TACT
SW03
TACT
R282
1K
C281
0.
01uF
C282
0.
01uF
SW05
TACT
C283
0.
01uF
R292
220
C292
0.
01uF
C291
0.
01uF
Y
W
D
291
R293
220
R294
220
C293
0.
01uF
C294
0.
01uF
R290
220
R291
220
Y
W
D
292
D
293
BLUE
C290
0.
01uF
R281
1K
SW02
TACT
12
34567
8
9
CZ2
3
3
1
2
A
K2
K1
IC
28
N
SA
D
500F
3
1
2
A
K2
K1
IC
27
N
SA
D
500F
SUB_GND
SUB_GND
JBL
OnBeat Xtreme service manual
Page 29 of 33
To:
All JBL Service Centers.
Models:
OnBeat Xtreme.
Subject:
iPod 30-pin Connector Board replacement.
In the event you receive an OnBeat Xtreme with the complaint : 1. Bad connection in the iPod dock or 2. Broken iPod
30-pin connector, perform the following repair.
Parts: iPod PCB part number: COP12449B. (Please remove wire if mounted on the new iPod PCB.)
Cushion part number: CHG1A497
Disassemble the dock arm:
1: Remove the cushion
2: Remove 4 x screws
3: Remove 4 x screws
4: Remove the front support
5: Remove 2 x screws on the back 6: Remove 2 x screws on the front
Gently click – don’t break!
7: Slide off the iPod support
8: Remove the iPod PCB
JBL
OnBeat Xtreme service manual
Page 30 of 33
9: Gently pull out the cable from the PCB by heating all the soldered joints at the same time, until all
connector pins are loose. We recommend using a flat 17mm soldering iron tip.
10: Re-mount connector tight to new PCB. 11: Resolder connector.
Re-assemble the dock arm:
A: Re-mount the iPod jack rubber
B: Mount the iPod PCB
C: Slide back the iPod support
Perform steps 6-5-4-3-2-1 from the disassembly procedure (see above).
Make sure the unit works after assembling by testing with an iPhone.
Model
Serial number
Status
Action
JBL OnBeat Xtreme
All
-
Replace iPod PCB
JBL
OnBeat Xtreme service manual
Page 31 of 33
Preparation
1. Save the new firmware "Fw_MCS_Odin_20110
929_8M.MCS" to USB stick. (Please make sure there's no other files in same USB stick.)
2. Connect the USB cable to the USB terminal on the rear panel of O
BX.
Rear panel of O
BX USB stick and adapter
3.
Make sure that no Apple device (iPhone, iPod, iPad) is docked in the OBX.
How To Upgrade
1. Press the two buttons (4th LED and 5th LED) below at the same time until the 4th LED color become
V a pink color.
Press these two buttons until th
H buttons
LED color changeV to pink.
2. Connect USB stick
with the new firmware Ln the 'USB' VRFNHW on the rear panel of OBX by using provided USB adapter.
3. When
the USB stick is connected, the 1st amber LED (power) will be blinking.
4.
Press the 5th button one time.
5. Then, 4th LED blink
s Blue->White->Blue for 20 seconds. (Blinking means upgrading.)
6. When the upgrade is done, 4th LED
still blinks, but the color changes to pink. (This means upgrade is completed successfully.).
7. After 10secs of 4th LED blinking, please
unplug the AC power cord. 5HPRYHWKH86%VWLFN
8.
End.
1. End.Please connect AC power cord again and turn Odin on.
How To Check the Version
Setting
General
About
JBL OnBeat Xtreme
Hardware Revision
1.0.
6
1st LED
2nd LED
3rd LED
4th LED
5th LED
1st LED
5th LED
4th LED
JBL
OnBeat Xtreme service manual
Page 32 of 33
SOFTWARE UPDATE PROCEDURE
Click on the first or last page to see other ON BEAT XTREME service manuals if exist.