JBL ON BEAT AIR (serv.man3) EMC - CB Certificate ▷ View online
www.tuv.com
Page 8 of 116
Report No.: 11023927 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
1
GENERAL
P
1.5
Components
P
1.5.1
General
P
Comply with IEC 60950-1 or relevant component
standard
standard
(see appended tables 1.5.1)
P
1.5.2
Evaluation and testing of components
Components which are
certified to IEC and/or
national standards are used
correctly within their ratings.
Components not covered by
IEC standards are tested
under the conditions present
in the equipment.
certified to IEC and/or
national standards are used
correctly within their ratings.
Components not covered by
IEC standards are tested
under the conditions present
in the equipment.
P
1.5.3
Thermal controls
No thermal controls.
N/A
1.5.4
Transformers
Transformers used are
suitable for their intended
application and comply with
the relevant requirements of
the standard and particularly
Annex C.
suitable for their intended
application and comply with
the relevant requirements of
the standard and particularly
Annex C.
P
1.5.5
Interconnecting cables
SELV output cable provided
as part of this equipment and
no higher energy levels than
240VA, it’s not possible to
present a hazard.
as part of this equipment and
no higher energy levels than
240VA, it’s not possible to
present a hazard.
P
1.5.6
Capacitors bridging insulation
Between lines: X2 type
capacitor (CX) according to
IEC 60384-14.
Between primary and
secondary: Y1 capacitor
(CY1), according to IEC
60384-14.
capacitor (CX) according to
IEC 60384-14.
Between primary and
secondary: Y1 capacitor
(CY1), according to IEC
60384-14.
P
1.5.7
Resistors bridging insulation
P
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
supplementary insulation
Only discharge resistors
bridging insulation between
L&N.
bridging insulation between
L&N.
P
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
between a.c. mains and other circuits
Between primary and
secondary: By resistors R36-
R41.
secondary: By resistors R36-
R41.
P
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
between a.c. mains and antenna or coaxial cable
N/A
1.5.8
Components in equipment for IT power systems
See only Norway deviation
N/A
www.tuv.com
Page 9 of 116
Report No.: 11023927 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
1.5.9
Surge suppressors
No such components
N/A
1.5.9.1
General
N/A
1.5.9.2
Protection of VDRs
N/A
1.5.9.3
Bridging of functional insulation by a VDR
N/A
1.5.9.4
Bridging of basic insulation by a VDR
N/A
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
insulation by a VDR
N/A
1.6
Power interface
P
1.6.1
AC power distribution systems
TN power system
P
1.6.2
Input current
Highest load according to
1.2.2.1 for this equipment is
the operation with the
maximum specified by the
manual instruction. (see
appended table 1.6.2)
1.2.2.1 for this equipment is
the operation with the
maximum specified by the
manual instruction. (see
appended table 1.6.2)
P
1.6.3
Voltage limit of hand-held equipment
This appliance is not hand-
held equipment.
held equipment.
N/A
1.6.4
Neutral conductor
The neutral conductor
insulated from earth and from
the body throughout the
equipment as if it were a line
conductor
insulated from earth and from
the body throughout the
equipment as if it were a line
conductor
P
1.7
Marking and instructions
P
1.7.1
Power rating and identification markings
See below
P
1.7.1.1
Power rating marking
P
Multiple mains supply connections..........................: Single power source
P
Rated voltage(s) or voltage range(s) (V) .............. : 100-240V~
P
Symbol for nature of supply, for d.c. only .............. : AC source
N/A
Rated frequency or rated frequency range (Hz) ... : 50/60Hz
P
Rated current (mA or A) ........................................ : 1.5A
P
1.7.1.2
Identification markings
P
Manufacturer’s name or trade-mark or identification
mark ...................................................................... :
mark ...................................................................... :
P
Model identification or type reference ................... : See page 5
P
www.tuv.com
Page 10 of 116
Report No.: 11023927 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
Symbol for Class II equipment only ...................... : 60417-1-IEC-5172 symbol
marked.
P
Other markings and symbols ................................ : Additional symbol or marking
does not give rise to
misunderstanding.
misunderstanding.
P
1.7.2
Safety instructions and marking
English and Germany version
provide.
(Version in other language will
be provided when submitted
for national approval)
be provided when submitted
for national approval)
P
1.7.2.1
General
P
1.7.2.2
Disconnect devices
Appliance inlet serves as
disconnect device.
disconnect device.
P
1.7.2.3
Overcurrent protective device
Not such equipment.
N/A
1.7.2.4
IT power distribution systems
N/A
1.7.2.5
Operator access with a tool
No operator accessible area
that needs to be accessed by
the use of a tool.
that needs to be accessed by
the use of a tool.
N/A
1.2.7.6
Ozone
Not such equipment.
N/A
1.7.3
Short duty cycles
Equipment is designed for
continuous operation.
continuous operation.
N/A
1.7.4
Supply voltage adjustment ................................... :
No voltage selector.
N/A
Methods and means of adjustment; reference to
installation instructions ......................................... :
installation instructions ......................................... :
N/A
1.7.5
Power outlets on the equipment .......................... :
No power outlets provided.
N/A
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) .......................... :
characteristics, cross-reference) .......................... :
Fuse marking provided on
PCB:F1 T3.15A 250V
PCB:F1 T3.15A 250V
P
1.7.7
Wiring terminals
See below.
P
1.7.7.1
Protective earthing and bonding terminals .......... :
Class I equipment. Protective
earthing terminal symbol
marked on appliance inlet.
earthing terminal symbol
marked on appliance inlet.
P
1.7.7.2
Terminals for a.c. mains supply conductors
The equipment with appliance
inlet is intended to use the
detachable type power supply
cord.
inlet is intended to use the
detachable type power supply
cord.
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
No d.c. mains supply.
N/A
1.7.8
Controls and indicators
No controls and indicators
N/A
1.7.8.1
Identification, location and marking ..................... :
N/A
1.7.8.2
Colours ................................................................ :
N/A
www.tuv.com
Page 11 of 116
Report No.: 11023927 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
1.7.8.3
Symbols according to IEC 60417 ........................ :
N/A
1.7.8.4
Markings using figures ....................................... :
N/A
1.7.9
Isolation of multiple power sources .................... :
Single power source
N/A
1.7.10
Thermostats and other regulating devices ......... :
Such devices not used.
N/A
1.7.11
Durability
The label was subjected to
the permanence of marking
test. The label was rubbed
with cloth soaked with water
for 15 sec. And then again for
15 sec. With the cloth soaked
with petroleum spirit.
After this test there was no
damage to the label. The
marking on the label did not
fade. There was no curling
and lifting of the label edge.
the permanence of marking
test. The label was rubbed
with cloth soaked with water
for 15 sec. And then again for
15 sec. With the cloth soaked
with petroleum spirit.
After this test there was no
damage to the label. The
marking on the label did not
fade. There was no curling
and lifting of the label edge.
P
1.7.12
Removable parts
No removable part.
N/A
1.7.13
Replaceable batteries ......................................... :
No battery provided.
N/A
Language(s) .........................................................:
1.7.14
Equipment for restricted access locations ........... :
Not intended for use in
restricted access locations.
restricted access locations.
N/A
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
No access with test finger and
test pin to any parts with only
basic insulation to ELV or
hazardous voltage.
test pin to any parts with only
basic insulation to ELV or
hazardous voltage.
P
2.1.1.1
Access to energized parts
See above.
P
Test by inspection .................................................:
P
Test with test finger (Figure 2A) ............................:
P
Test with test pin (Figure 2B) ................................:
P
Test with test probe (Figure 2C) ............................:
N/A
2.1.1.2
Battery compartments
No battery compartment.
N/A
2.1.1.3
Access to ELV wiring
No ELV wiring in operator
accessible area.
accessible area.
N/A
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
distance through insulation (mm)
(see appended table 2.10.5)
Click on the first or last page to see other ON BEAT AIR (serv.man3) service manuals if exist.