JBL ENCOUNTER (serv.man6) EMC - CB Certificate ▷ View online
.
.
.
.
.
.
.
.
.
Harman Multimedia
DECLARATION OF CONFORMITY STATEMENT
Responsible Party:
Manufacturer:
Equipment : Multimedia PC Speaker System
Model : JBL ENCOUNTER
Revision: None
We hereby certify that the named system was tested and conforms to CE EN 60950-1.
Harman Multimedia has received notification to apply the CE and TUV marks to this product.
The JBL ENCOUNTER uses the following external power supply:
Leader Electronics Inc. Model# TA66183*** 18Vac, 3.5 Amp output.
The power supply is covered by CB Certificate JPTUV-003800-A1/M1.
Model : JBL ENCOUNTER
Revision: None
We hereby certify that the named system was tested and conforms to CE EN 60950-1.
Harman Multimedia has received notification to apply the CE and TUV marks to this product.
The JBL ENCOUNTER uses the following external power supply:
Leader Electronics Inc. Model# TA66183*** 18Vac, 3.5 Amp output.
The power supply is covered by CB Certificate JPTUV-003800-A1/M1.
Additional information
The system was tested by:
NEMKO Compliance
P.O. Box 73, Bundern
N-0314 Oslo, Norway
The supporting documents are as follows:
CB Test Certificate 30868
The system was tested by:
NEMKO Compliance
P.O. Box 73, Bundern
N-0314 Oslo, Norway
The supporting documents are as follows:
CB Test Certificate 30868
15 October 2004
CE EMC Evaluation report # 2004090584 17 September 2004
TUV Certificate S72042620
TUV Certificate S72042620
11 August 2004
CB Certificate JPTUV-003800-A1/M1 14 February 2003
____________________________ ______05_November 2004_____
Bruce Ryan, Program Manager
DATE
Harman Multimedia
CE mark applied
TUV mark applied
TRF No.:
I950___D
TRF originator: FIMKO
Page 2 of 74
<E 2060978E01>
Test item particulars:
Equipment mobility ........................................................: movable equipment
Operating condition .......................................................: continuous operation
Tested for IT power systems.........................................: No
IT testing, phase-phase voltage (V) ..............................: N.A.
Class of equipment........................................................: Class II equipment
Mass of equipment (kg).................................................: <1kg
Protection against ingress of water ...............................: IP20
Possible test case verdicts:
- test case does not apply to the test object..................: N(.A.)
- test object does meet the requirement .......................: P(ass)
- test object does not meet the requirement .................: F(ail)
General remarks:
Equipment mobility ........................................................: movable equipment
Operating condition .......................................................: continuous operation
Tested for IT power systems.........................................: No
IT testing, phase-phase voltage (V) ..............................: N.A.
Class of equipment........................................................: Class II equipment
Mass of equipment (kg).................................................: <1kg
Protection against ingress of water ...............................: IP20
Possible test case verdicts:
- test case does not apply to the test object..................: N(.A.)
- test object does meet the requirement .......................: P(ass)
- test object does not meet the requirement .................: F(ail)
General remarks:
"(see remark #)" refers to a remark appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
The test results presented in this report relate only to the object tested.
This report shall not be reproduced except in full without the written approval of the testing laboratory.
Comments:
Brief description of the test sample:
The equipment are an external AC to AC and AC to DC linear power supply adaptor.(plug-in type)
The adaptor’s top enclosure is secured to bottom enclosure by ultra-sound welding.
There are two alternative enclosures.
The equipment are an external AC to AC and AC to DC linear power supply adaptor.(plug-in type)
The adaptor’s top enclosure is secured to bottom enclosure by ultra-sound welding.
There are two alternative enclosures.
Unless otherwise specified, all tests were performed on models: TEAC-48-141300V, TEAC-48-160800V,
TEAC-48-160900V, TEAC-48-220700V, TEAC-48-220800V, TEAC-48-270900V, TEAD-48-052000V,
TEAD-48-062000V, TEAD-48-090800V, and TEAD-240600V used type 1 case to represent the other
similar models.
TEAC-48-160900V, TEAC-48-220700V, TEAC-48-220800V, TEAC-48-270900V, TEAD-48-052000V,
TEAD-48-062000V, TEAD-48-090800V, and TEAD-240600V used type 1 case to represent the other
similar models.
Declaration of types:
Model:TEAC-48-XYZ(AC to AC adaptor), TEAD-48-XYZ(AC to AD adaptor), TEAC-XYZ(AC to AC adaptor)
series
X stands for output voltage
Y stands for output current
Z Can be V or V1
Model:TEAC-48-XYZ(AC to AC adaptor), TEAD-48-XYZ(AC to AD adaptor), TEAC-XYZ(AC to AC adaptor)
series
X stands for output voltage
Y stands for output current
Z Can be V or V1
(The different between V and V1 is the rated cross-section area of output cord:
V: can be used 18 to 24AWG; V1: can be used 18 to 20AWG min.)
The following models(page 10 to page 11) are of exactly same construction but have alternative model
numbers in the parentheses.
e.x. TEAD-48-451500V(TE-451500V)
The test samples are pre-production units without serial number.
The following models(page 10 to page 11) are of exactly same construction but have alternative model
numbers in the parentheses.
e.x. TEAD-48-451500V(TE-451500V)
The test samples are pre-production units without serial number.