JBL DUET III EMC - CB Certificate ▷ View online
- Page 2 of 6 -
www.nemko.com
Report No. 116366
1.2.12.101
Addition:
VTM CLASS MATERIAL: Thin MATERIALS fulfil the
specified conditions during the test of clause A.101
applied for materials that the test and evaluation of
clauses A.6 to A.10 is difficult to enforce. Materials are
classified to three classifications as VTM-0, VTM-1 and
VTM-2 according to the conditions after the removal of
the test flame.
VTM CLASS MATERIAL: Thin MATERIALS fulfil the
specified conditions during the test of clause A.101
applied for materials that the test and evaluation of
clauses A.6 to A.10 is difficult to enforce. Materials are
classified to three classifications as VTM-0, VTM-1 and
VTM-2 according to the conditions after the removal of
the test flame.
The material is not used
N/A
1.7.101
Addition:
Marking for CLASS 0I EQUIPMENT
Marking for CLASS 0I EQUIPMENT
For CLASS 0I EQUIPMENT, the following instruction
shall be indicated on the visible place of the mains plug
or the main body:
shall be indicated on the visible place of the mains plug
or the main body:
“Provide an earthing connection”
Moreover, for CLASS 0I EQUIPMENT, the following
instruction shall be indicated on the visible place of the
main body or written in the operating instructions:
instruction shall be indicated on the visible place of the
main body or written in the operating instructions:
“Provide an earthing connection before the mains plug
is connected to the mains. And, when disconnecting
the earthing connection, be sure to disconnect after
pulling out the mains plug from the mains.”
is connected to the mains. And, when disconnecting
the earthing connection, be sure to disconnect after
pulling out the mains plug from the mains.”
Class III equipment
supplied by a separately
certified adaptor. (refer
to summary of testing)
supplied by a separately
certified adaptor. (refer
to summary of testing)
N/A
2.1.1.1
Replacement:
Replace “IEC 60083” to “IEC 60083 or JIS C 8303” in
2.1.1.1 b).
Replace “IEC 60083” to “IEC 60083 or JIS C 8303” in
2.1.1.1 b).
Considered
P
2.6.3.1
Addition:
Add the following after 1st paragraph.
Add the following after 1st paragraph.
This also applies to the conductor of lead wire for
protective earthing of CLASS 0I EQUIPMENT.
protective earthing of CLASS 0I EQUIPMENT.
Class III equipment
supplied by a separately
certified adaptor. (refer
to summary of testing)
supplied by a separately
certified adaptor. (refer
to summary of testing)
N/A
2.6.4.1
Replacement:
Replace 2nd sentence in 1st paragraph.
Replace 2nd sentence in 1st paragraph.
For CLASS I EQUIPMENT with a DETACHABLE
POWER SUPPLY CORD, the earthing terminal in the
appliance inlet is regarded as the main protective
earthing terminal.
POWER SUPPLY CORD, the earthing terminal in the
appliance inlet is regarded as the main protective
earthing terminal.
Class III equipment.
N/A
2.6.5.4
Replacement:
Replace 1st sentence.
Replace 1st sentence.
Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later than
the supply connections in each of the following:
EQUIPMENT shall make earlier and break later than
the supply connections in each of the following:
Class III equipment.
N/A
- Page 3 of 6 -
www.nemko.com
Report No. 116366
2.6.101
Addition:
Earthing of CLASS 0I EQUIPMENT
Earthing of CLASS 0I EQUIPMENT
Plugs with a lead wire for earthing shall not be used for
equipment having a rated voltage exceeding 150V.
equipment having a rated voltage exceeding 150V.
For plugs with a lead wire for earthing, the lead wire
shall not be earthed by a clip.
shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with an
earthing terminal or lead wire for earthing in the
external where easily visible.
earthing terminal or lead wire for earthing in the
external where easily visible.
Class III equipment
supplied by a separately
certified adaptor. (refer
to summary of testing)
supplied by a separately
certified adaptor. (refer
to summary of testing)
N/A
3.2.5
Delete 1) in Table 3B.
Considered.
P
4.2.8
Addition:
Add the following informative remark after the last
sentence.
Add the following informative remark after the last
sentence.
Remark - IEC 61965 is also applicable instead of IEC
60065.
60065.
No cathode tubes.
N/A
4.5.1
Addition:
Add the following to suffix 5) as specified in
“Conditions applicable to Table 4A, Parts 1 and 2”.
Add the following to suffix 5) as specified in
“Conditions applicable to Table 4A, Parts 1 and 2”.
With regard to Table 4A, insulating materials
complying with Japanese requirements (refer to
Japanese differences for the current IEC 60335-1 (3rd
Edition) in CB Bulletin 101B) are also acceptable.
complying with Japanese requirements (refer to
Japanese differences for the current IEC 60335-1 (3rd
Edition) in CB Bulletin 101B) are also acceptable.
Add a suffix 7) in “Conditions applicable to Table 4A,
Parts 1 and 2”.
Parts 1 and 2”.
In the right column of Table 4A, Part 1, add suffix 7) to
“50” (K), corresponding to “- without T – marking” in
the left column so as to become “50 7)”.
“50” (K), corresponding to “- without T – marking” in
the left column so as to become “50 7)”.
Add 7) to Table 4A, Part 2 as follows.
7) This value shall apply only to wiring or cords
complying with relevant IEC standards. Others shall
comply with Japanese requirements (refer to Japanese
differences for the current IEC 60335-1 (3rd Edition) in
CB Bulletin 101B).
complying with relevant IEC standards. Others shall
comply with Japanese requirements (refer to Japanese
differences for the current IEC 60335-1 (3rd Edition) in
CB Bulletin 101B).
Considered.
P
4.7.3.2
Addition:
Add the following in 7th paragraph.
Add the following in 7th paragraph.
- for thin materials, e.g., flexible printed boards, etc.,
used inside equipment, be of FLAMMABILITY CLASS
VTM-2 or better.
used inside equipment, be of FLAMMABILITY CLASS
VTM-2 or better.
No such thin materials
used.
used.
N/A
- Page 4 of 6 -
www.nemko.com
Report No. 116366
5.1.6
Replacement:
Replace Table 5A.
Replace Table 5A.
Class III equipment.
N/A
5.3.8.2
Replacement:
Replace 3rd Item as follows.
Replace 3rd Item as follows.
- BASIC INSULATION between the PRIMARY
CIRCUIT and accessible conductive parts of CLASS I
or 0I EQUIPMENT;
CIRCUIT and accessible conductive parts of CLASS I
or 0I EQUIPMENT;
Class III equipment.
N/A
Annex A
Addition:
Add the subclause A.101 with the title “Flammability
tests for classifying materials VTM” and the following:
Add the subclause A.101 with the title “Flammability
tests for classifying materials VTM” and the following:
Thin sheet materials shall comply with ISO 9773.
The material is not used
N/A
Annex G
Addition:
Add the following to the Note for Table G.1.
Add the following to the Note for Table G.1.
2. In Japan, MAINS TRANSIENT VOLTAGE for
equipment with a Nominal AC MAINS SUPPLY
VOLTAGE of 100V is to be decided based on the
column where Nominal AC MAINS SUPPLY
VOLTAGE in Table G.1 is 150V.
equipment with a Nominal AC MAINS SUPPLY
VOLTAGE of 100V is to be decided based on the
column where Nominal AC MAINS SUPPLY
VOLTAGE in Table G.1 is 150V.
Class III equipment.
N/A
Annex P
Addition:
Add “IEC 61965:2000, Mechanical Safety for Cathode
Ray Tubes”.
Add “IEC 61965:2000, Mechanical Safety for Cathode
Ray Tubes”.
Not used.
N/A
Annex U
Replacement:
Replace 2nd paragraph.
Replace 2nd paragraph.
This annex covers to round winding wires having
diameters between 0.05 mm and 5.00 mm.
diameters between 0.05 mm and 5.00 mm.
Not used.
N/A
- Page 5 of 6 -
www.nemko.com
Report No. 116366
U.2.1
Replacement:
Electric strength
The test sample is prepared according to IEC 60851-
5:1997, 4.4.1 (for a twisted pair). The sample is then
subjected to the test of 5.2.2 of this standard, with a
test voltage not less than twice the appropriate voltage
in table 5B (see 5.2.2) of this standard. However, the
minimum values shall be as follows:
Electric strength
The test sample is prepared according to IEC 60851-
5:1997, 4.4.1 (for a twisted pair). The sample is then
subjected to the test of 5.2.2 of this standard, with a
test voltage not less than twice the appropriate voltage
in table 5B (see 5.2.2) of this standard. However, the
minimum values shall be as follows:
- for BASIC INSULATION or SUPPLEMENTARY
INSULATION, 3000 V, or;
INSULATION, 3000 V, or;
- for REINFORCED INSULATION, 6000 V.
Not used.
N/A
U.2.2
Replacement:
Flexibility and adherence
Flexibility and adherence
Test 8 of IEC 60851-3:1996, 5.1.1, using the mandrel
diameters of table U.1. The test sample is then
examined in accordance with IEC 60851-3:1996,
5.1.1.4, followed by the test of 5.2.2 of this standard
except applying the test voltage between the wire and
the mandrel. A test voltage shall not be less than twice
the appropriate voltage in table 5B (see 5.2.2) of this
standard. However, the minimum values shall be as
follows:
diameters of table U.1. The test sample is then
examined in accordance with IEC 60851-3:1996,
5.1.1.4, followed by the test of 5.2.2 of this standard
except applying the test voltage between the wire and
the mandrel. A test voltage shall not be less than twice
the appropriate voltage in table 5B (see 5.2.2) of this
standard. However, the minimum values shall be as
follows:
- for BASIC INSULATION or SUPPLEMENTARY
INSULATION, 1500 V, or;
INSULATION, 1500 V, or;
- for REINFORCED INSULATION, 3000 V.
NOTE: “twice” in the 6th line is deleted – ref.
confirmation by Japan NCB – JQA.
confirmation by Japan NCB – JQA.
Not used.
N/A
Table U.1
Replacement:
Mandrel diameter
Mandrel diameter
The tension to be applied to the wire during winding on
the mandrel is calculated from the wire diameter to be
equivalent to 118 Mpa ± 10 % (118 N/mm2 ± 10 %).
No used.
N/A
Click on the first or last page to see other DUET III service manuals if exist.