JBL DUET III EMC - CB Certificate ▷ View online
- Page 5 of 5 -
www.nemko.com
Report No. 116366
3.2.1.2
Equipment connected to centralized d.c. power
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, wiring, marking and
installation instruction requirements.
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, wiring, marking and
installation instruction requirements.
The equipment is not for
connection to a d.c. mains
supply.
connection to a d.c. mains
supply.
N/A
4.2.8.1
Enclosures around CRT’s with a face diameter of
160 mm or more are required to reduce the risk
of injury due to the implosion of the CRT.
160 mm or more are required to reduce the risk
of injury due to the implosion of the CRT.
No CRTs in the equipment.
N/A
4.3.2
Equipment with handles is required to comply
with special loading tests.
with special loading tests.
Compliance. P
5.1.8.3
Equipment intended to receive
telecommunication ringing signals is required to
comply with a special touch current
measurement tests.
telecommunication ringing signals is required to
comply with a special touch current
measurement tests.
No TNV circuitry.
N/A
6.2.1
Enamel coating on winding wire not considered
electrical separation unless subjected to special
investigation.
electrical separation unless subjected to special
investigation.
No TNV circuitry.
N/A
6.4
Equipment intended for connection to
telecommunication network outside plant cable is
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
telecommunication network outside plant cable is
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
No TNV circuitry.
N/A
6.5
Equipment connected to a telecommunications
network and supplied with an earphone intended
to be held against, or in the ear is required to
comply with special acoustic pressure tests.
network and supplied with an earphone intended
to be held against, or in the ear is required to
comply with special acoustic pressure tests.
No TNV circuitry.
N/A
M.2
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
permitted if the equipment is subjected to special
installation and performance restrictions.
No TNV circuitry.
N/A
- Page 1 of 1 -
www.nemko.com
Report No. 116366
ATTACHMENT: KOREAN DIFFERENCES
Test results according to CB BULLETIN No. 112A, December 2006
Clause
Requirements – Test
Result – Remark
Verdict
1.5.101 Addition
Plugs for the connection of the apparatus to the
supply mains shall comply with the Korean
requirement (KSC 8305 and 8305).
supply mains shall comply with the Korean
requirement (KSC 8305 and 8305).
Class III equipment supplied by a
separately certified adaptor.
(refer to summary of testing)
separately certified adaptor.
(refer to summary of testing)
N/A
7 Addition
EMC
The apparatus shall comply with the relevant
CISPR standards.
The apparatus shall comply with the relevant
CISPR standards.
Compliance with EMC must be
considered when marketing in
Korea.
considered when marketing in
Korea.
⎯
- Page 1 of 2 -
www.nemko.com
Report No. 116366
ATTACHMENT: SINGAPORE DIFFERENCES
to IEC 60950-1 (ed.1)
No
Item
Requirement
Result - Remark
Verdict
www.safety.org.sg/
, ref. Singapore Consumer Protection (Safety Requirements) - Information
booklet - chapter 7 (page 21 - 24). Based on information by Singapore NCB – PSB Corp.
7 SAFETY AUTHORITY’S REQUIREMENTS
The Safety Authority monitors the safety of the controlled goods sold in Singapore by
investigating all complaints, incidents and accidents reported to the authority. Experiences
gained are translated into the Safety Authority’s Requirements. These requirements are to be
fulfilled in addition to the applicable safety standards.
investigating all complaints, incidents and accidents reported to the authority. Experiences
gained are translated into the Safety Authority’s Requirements. These requirements are to be
fulfilled in addition to the applicable safety standards.
Applicable to all electrical products
2
All appliances
All appliances must be tested to 230
VAC.
VAC.
Class III equipment.
N/A
3
Voltage selector
(voltage mis-match
test)
(voltage mis-match
test)
Appliance fitted with voltage selector
shall be tested as follows:
Connect appliance to 230 VAC
mains with voltage selector switch to
settings not suitable for operation at
230 VAC.
shall be tested as follows:
Connect appliance to 230 VAC
mains with voltage selector switch to
settings not suitable for operation at
230 VAC.
No voltage selector
N/A
4
Tropical condition
test
test
All appliances (with tropical test
requirements in applicable
Standards) shall comply with the
tropical condition test as stated in
the relevant IEC Standards.
requirements in applicable
Standards) shall comply with the
tropical condition test as stated in
the relevant IEC Standards.
Considered. P
5
Class I appliances
(3-pin mains plug)
All Class I appliances must be fitted
with 3-pin mains plugs complied
with SS 145/SS 472 that are
registered with the Safety Authority.
with 3-pin mains plugs complied
with SS 145/SS 472 that are
registered with the Safety Authority.
Class III equipment.
N/A
6
Class II appliances
(mains plug)
a) All Class II appliances must be
fitted with 2-pin mains plug
(Appendix W) complied with IEC 83:
1975 (Standard C5, Version II) or
EN 50075: 1991.
fitted with 2-pin mains plug
(Appendix W) complied with IEC 83:
1975 (Standard C5, Version II) or
EN 50075: 1991.
b) Class II appliances that are fitted
with 3-pin mains plugs must use
plugs that are complied with SS 145
and registered with the Safety
Authority.
with 3-pin mains plugs must use
plugs that are complied with SS 145
and registered with the Safety
Authority.
Class III equipment
supplied by a
separately certified
adaptor.
supplied by a
separately certified
adaptor.
N/A
7
Appliances rated
≥
3 kW or connected
to fixed wiring
to fixed wiring
Electric appliance
≥ 3 kW must be
connected to fixed wiring. All
connection to fixed wiring must be in
accordance with Code of Practice
CP5.
connection to fixed wiring must be in
accordance with Code of Practice
CP5.
The rated power is
less than 3kW.
less than 3kW.
N/A
8
Detachable power
Detachable power cord set must be
Class III equipment
N/A
- Page 2 of 2 -
www.nemko.com
Report No. 116366
cord set (consists
of mains plug,
mains cord and
appliance
connector
of mains plug,
mains cord and
appliance
connector
listed in the test report critical
component list.
component list.
supplied by a
separately certified
adaptor.
separately certified
adaptor.
9
Circuit diagrams
Circuit diagrams must be indicated
with component’s values for
products tested to IEC 60065 and
IEC 60950.
with component’s values for
products tested to IEC 60065 and
IEC 60950.
The rated values for
critical components
are listed on table
1.5.
critical components
are listed on table
1.5.
P
10
Circuit diagrams of
electronic modules
in electrical
appliances
electronic modules
in electrical
appliances
Circuit diagrams of the electronic
modules in the electrical appliances
must be provided.
modules in the electrical appliances
must be provided.
Considered. -
11
Controlled goods
likely to be treated
as toy by children
likely to be treated
as toy by children
Controlled goods, having an
enclosure, which is shaped and
decorated so that it is likely to be
treated as a toy by children, shall
not be accepted for certification and
registration.
enclosure, which is shaped and
decorated so that it is likely to be
treated as a toy by children, shall
not be accepted for certification and
registration.
The equipment is
not treated as toy
by children.
not treated as toy
by children.
N/A
Applicable to AC adaptor
13
3-pin AC adaptor
Test report showing that the 3-pin
complied with sub-clauses 12.1 &
12.3 of SS 246 must be submitted.
complied with sub-clauses 12.1 &
12.3 of SS 246 must be submitted.
Class III equipment.
N/A
14
2-pin
AC
adaptor
The 2-pin (Appendix W) shall
comply with IEC 83: 1975 (Standard
C5, Version II) or EN 50075
comply with IEC 83: 1975 (Standard
C5, Version II) or EN 50075
Class III equipment.
N/A
15
Detachable power
supply cord set not
supplied by
Registered
Supplier
supply cord set not
supplied by
Registered
Supplier
Registered Supplier who is not
supplying the detachable power
supply cord set together with the AC
Adaptor must provide written
instruction to its customer on the
type of approved detachable power
cord set to use.
supplying the detachable power
supply cord set together with the AC
Adaptor must provide written
instruction to its customer on the
type of approved detachable power
cord set to use.
Class III equipment.
N/A
Applicable to computer products
16
CD/DVD ROM
(used in personal
computer)
(used in personal
computer)
Test certificate showing that
CD/DVD ROM has complied with
IEC 825 must be provided.
CD/DVD ROM has complied with
IEC 825 must be provided.
Not used.
N/A
17
Modem Card (used
in personal
computer)
in personal
computer)
Modem card incorporated in the
personal computer must be tested
at set level (sub-clauses 5.1 & 6 of
IEC 60950) or at component level.
personal computer must be tested
at set level (sub-clauses 5.1 & 6 of
IEC 60950) or at component level.
Not used.
N/A
Click on the first or last page to see other DUET III service manuals if exist.