Harman Kardon SUB-TS 11 EMC - CB Certificate ▷ View online
page 31 of 32
Ref.No.: 313603
IEC 60065
Cl.
Requirement - Test
Result - Remark
Verdict
16.3b
(16.4b)
Delete “Subclause 3.1 of IEC Publication
60227-2: Part 2: Test Methods“ and insert
“Subclause 9.1 of SS 236“:
60227-2: Part 2: Test Methods“ and insert
“Subclause 9.1 of SS 236“:
9.1 Flexing test (except for tinsel cords,
twisted twin and single core cords). The test
shall be carried out by means of the
apparatus shown in Figure 5. This apparatus
has a carrier C supporting two pulleys A and
B arranged so that the cord is horizontal
between the pulleys. The carrier moves
backward and forward over a distance of 1 m
at an approximately constant speed of 0.33
m/s.
twisted twin and single core cords). The test
shall be carried out by means of the
apparatus shown in Figure 5. This apparatus
has a carrier C supporting two pulleys A and
B arranged so that the cord is horizontal
between the pulleys. The carrier moves
backward and forward over a distance of 1 m
at an approximately constant speed of 0.33
m/s.
A sample of flexible cord about 5 m long shall
be stretched over the pulleys as shown in the
figure, each end being loaded with a weight.
The weight and the diameter of the pulleys A
and B shall be given in Table 1.
be stretched over the pulleys as shown in the
figure, each end being loaded with a weight.
The weight and the diameter of the pulleys A
and B shall be given in Table 1.
Screene cords in accordance with Table 7 shall
be tested before application of the screen and
outer sheath.
be tested before application of the screen and
outer sheath.
The pulleys shall have a semi-circular shaped
groove for circular cords and a flat groove for
parallel twin cords. The restraining clamps D shall
be fixed so that the pull is always applied by the
weight from which the carrier is moving away.
The carrier shall make 30 000 backward and
forward movements (60 000 single strokes). Each
conductor of the sample shall be loaded with the
current specified in Table 2.
groove for circular cords and a flat groove for
parallel twin cords. The restraining clamps D shall
be fixed so that the pull is always applied by the
weight from which the carrier is moving away.
The carrier shall make 30 000 backward and
forward movements (60 000 single strokes). Each
conductor of the sample shall be loaded with the
current specified in Table 2.
For twin cords and for light PVC-sheated 3-core
cords, the voltage between the conductors shall
be approximately 230 V a.c. For all other cords
having three or more cores a three-phase a.c.
voltage of about 400 V shall be applied to three
conductors, any additional conductors being
connected to the neutral.
cords, the voltage between the conductors shall
be approximately 230 V a.c. For all other cords
having three or more cores a three-phase a.c.
voltage of about 400 V shall be applied to three
conductors, any additional conductors being
connected to the neutral.
During the test no open-circuit in any core or
short-circuit between cores shall occur.
short-circuit between cores shall occur.
After the test, any sheath on cords having three
or more cores shall be removed. The cord, or the
laid up cores, shall then withstand the voltage test
specified in Subclause 8.2 or 8.3 as appropriate,
but with a test voltage not exceeding 2000 V.
or more cores shall be removed. The cord, or the
laid up cores, shall then withstand the voltage test
specified in Subclause 8.2 or 8.3 as appropriate,
but with a test voltage not exceeding 2000 V.
TABLE 1, TABLE 2, FIGURES 4 and 5, see the
CB BULLETIN
Noted
TRF No.: I60065__C
page 32 of 32
Ref.No.: 313603
IEC 60065
Cl.
Requirement - Test
Result - Remark
Verdict
TRF No.: I60065__C
National differences KOREA
IEC 60065, 6
th
edition
CB Bulletin 105A / KR 03 I
5.101 Addition
Other marking;
Wording “ “ ( See the CB Bulletine) or an
information regulated in IEC Publication 60417
giving high voltage warning to layman shall be
marked, if an apparatus contains a part more
than 600 volts.
information regulated in IEC Publication 60417
giving high voltage warning to layman shall be
marked, if an apparatus contains a part more
than 600 volts.
N
15.1.1
Plugs for the connection of the apparatus to the
supply mains and socket outlets for providing
mains power to other apparatus shall comply with
the Korean requirements (KSC 8300 and 8305).
supply mains and socket outlets for providing
mains power to other apparatus shall comply with
the Korean requirements (KSC 8300 and 8305).
P
31
Radio frequency Interference
The apparatus shall comply with the relevant
CISPR requirements. (EMC=EMI + EMS)
CISPR requirements. (EMC=EMI + EMS)
Not
checked
313603
313603
313603
313603
313603
313603
Click on the first or last page to see other SUB-TS 11 service manuals if exist.