Harman Kardon SoundSticks II EMC - CB Certificate ▷ View online
Page 3 of 4
ST-05368-01
Particulars: test item vs. test requirements
Equipment mobility ..................................... : Movable (Transportable)
Operating condition ..................................... : Continuous
Mains supply tolerance (%) ......................... : + 6 %, + 10 % and – 10 % (the test voltage + 10 % is
required by the manufacturer)
Tested for IT power systems ...................... : Yes
IT testing, phase-phase voltage (V) ........... : 230 V for Norway
Class of equipment ..................................... : Class II
Mass of equipment (kg) ............................... : 0.23kg
Protection against ingress of water ............ : IP20
Test case verdicts
Test case does not apply to the test object : N/A (Not Applicable)
Test item does meet the requirement ......... : P (Pass)
Test item does not meet the requirement ... : F (Fail)
Testing
Date of receipt of test item .......................... : --
Date(s) of performance of test .................... : --
General remarks
The test result presented in this report relate only to the object(s) tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
“(see Appendix #)” refers to additional information appended to the report.
“(see appended table #)” refers to a table appended to the report.
Throughout this report a comma (point) is used as the decimal separator.
Additional information
Additional special deviations of CN (China) of IEC 60950, 3rd ed. are checked.
General product information:
For Model NU40-2******-I3:
a. The 1
st
to 3
rd
“*” denote the output voltage, which can be 050 (5.0 Vdc) to 240 (24 Vdc).
b. The 4
th
to 6
th
“*” denote the output current, which can be 050 (0.5 A) to 400 (4 A).
Model PJP-PS02 is identical to model NU40-2120300-I3 except for model designation.
Models NU40-2100400-I3, NU40-2240050-I3 and NU402050400-I3 are tested as the representatives of this
series.
Modification (01) to test report No. ST-05368 (CB Cert. No.: SE-50236):
The original Test Report Ref. ST-05368, dated January 6, 2006 was modified on December 21, 2007 to
include the following changes and/or additions, which were considered technical modifications:
-
Add an identical model.
-
Add a trademark “YAMAHA”.
-
Add an alternative PCB layout.
-
Delete one factory “Leader Electronics (Jiangsu) Inc.”
After review, no additional testing were considered necessarry.
Page 4 of 4
ST-05368-01
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
1.7
Marking and instructions
1.7.1
Power rating
P
Rated voltage(s) or voltage range(s) (V) ............ : 100 – 240 Vac
P
Symbol for nature of supply, for d.c. only............ : The EUT is supplied by AC
mains
N/A
Rated frequency or rated frequency range (Hz) : 50 / 60 Hz
P
Rated current (mA or A) ..................................... : 1.2 A
P
Manufacturer’s name or trademark or
identification mark ...........................................:
LEI, YAMAHA
P
Type/model or type reference ..........................: NU40-2******-I3, PJP-PS02
P
Symbol of for Class II equipment only ............... :
P
Other symbols .................................................... : Symbols are used according to
IEC 60417-1
P
Certification marks ............................................. :
N/A
1.7.2
Safety instructions
The English “I.T.E. POWER
SUPPLY” will be provided with
the unit
P
1.7.3
Short duty cycles
The EUT is continuous
operating type
N/A
1.7.4
Supply voltage adjustment ................................. : Only one power supply voltage
range
N/A
1.7.5
Power outlets on the equipment ........................ : No such components within the
EUT
N/A
1.7.6
Fuse identification .............................................. : The “F1” and “T2AL 250V” are
marked adjacent to the main
fuse
P
1.7.7
Wiring terminals
P
1.7.7.1
Protective earthing and bonding terminals ......... : Approved appliance coupler is
provided
N/A
1.7.7.2
Terminal for a.c. mains supply conductors
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
N/A
1.7.8
Controls and indicators
P
1.7.8.1
Identification, location and marking .................... : No control and indicator within
the EUT
N/A
Appendix 1
Page 1 of 1
ST-05368-01
PCB layout
Click on the first or last page to see other SoundSticks II service manuals if exist.