Harman Kardon DVD 25 EMC - CB Certificate ▷ View online
-
IEC 60065, 6th edition : 1998
-
- Page 17 of 32 -
Order No. 200225249
External clearance and creepage
distances appropriate for the voltage
across the device when opened
distances appropriate for the voltage
across the device when opened
N
14.5.1.1
a) Thermal cut-outs separately
approved
approved
N
b) Thermal cut-outs tested as part of
the submission
the submission
N
14.5.1.2
a) Thermal links separately
approved
approved
N
b) Thermal links tested as part of the
submission
submission
N
14.5.1.3
Thermal devices resettable by
soldering
soldering
N
14.5.2.1
Fuse-links in the mains circuit
according to IEC 60 127
according to IEC 60 127
P
Circuit
Manufacturer
Dimen-
Approved
Marking of
Marking
Current
diagram
sions
by
rated current,
close to
through
informa-
pre-arcing time
the com-
the fuse
tion
and current
ponent
in normal
Part No
characteristic
operation
F1
Littlefuse
5x20mm
VDE
T1AL/250V
T1A/250VAC
0.1A
14.5.2.2
Correct marking of fuse-links
adjacent to holder
adjacent to holder
See above
P
14.5.2.3
Not possible to connect fuses in
parallel
parallel
P
14.5.2.4
Not possible to touch hazardous live
parts when replacing fuse-links
without the use of a tool
parts when replacing fuse-links
without the use of a tool
A tool must be used to change the fuse. The fuse is
located inside the enclosure.
located inside the enclosure.
P
14.5.3
PTC -S thermistors comply with
IEC 60 738
IEC 60 738
None
N
PTC -S devices (>15 W) category
FV 1 or better
FV 1 or better
N
14.5.4
Circuit protectors have adequate
breaking capacity and their position
is correctly marked
breaking capacity and their position
is correctly marked
F1 conform to IEC60127 and have an adequate breaking
capacity of 35A.
Fuse replacement marking place close to fuses.
capacity of 35A.
Fuse replacement marking place close to fuses.
P
14.6
Switches
P
Manually operated mechanical
switch (MOMS) conductively
connected to the mains
switch (MOMS) conductively
connected to the mains
P
-
IEC 60065, 6th edition : 1998
-
- Page 18 of 32 -
Order No. 200225249
Part No
Function
Manufacturer
Type
Rated
Marking
Marking
All-
One
Name
Trademark
V
A
Surge
pole pole
current
SW1
X
Zhang Jia Gang
PS4
250
10
80
14.6.1
Permanently connected equipment
provided with an all-pole mains
switch unless 5.4.2 is met
provided with an all-pole mains
switch unless 5.4.2 is met
N
14.6.2
Manually operated mechanical
switch (MOMS), required where
power consumption > 15 W and/or
peak voltage > 4 kV
switch (MOMS), required where
power consumption > 15 W and/or
peak voltage > 4 kV
Yes
P
Switch readily accessible and not in
mains cord
mains cord
On front panel
P
Exception for automatic switching
N
Exception for continuous operation
N
14.6.3
Manually operated mechanical
switch (MOMS): switch indication On
position clearly discernible
switch (MOMS): switch indication On
position clearly discernible
Red LED on front panel illuminates.
P
Indication by marking meets Cl. 5
N
Indication of the OFF position
N
14.6.4
Manually operated mechanical
switch (MOMS) fitted, is there a
Stand-by mode
switch (MOMS) fitted, is there a
Stand-by mode
Yes
P
Stand-by mode clearly discernible
Red LED on front panel illuminates.
P
Exception for low Stand-by current
< 0,7 mA (peak)
< 0,7 mA (peak)
N
14.6.5
Components bridging contacts of
mains switches comply with 14.1 a)
or 14.2.2
mains switches comply with 14.1 a)
or 14.2.2
Capacitor C1 bridges the mains switch. Complies with
14.2.2 – Y2
14.2.2 – Y2
P
14.6.6
Manually operated mechanical
switches (MOMS) separately
approved to IEC 61 058-1
switches (MOMS) separately
approved to IEC 61 058-1
Complies with IEC 60065 6
th
ed., approved by VDE
P
Manually operated mechanical
switch (MOMS) tested as part of the
equipment complies with 14.6.7,
14.6.10 and 20.1.4 and meets
14.6.8 and/or 14.6.9 and Annex G
(G1.1)
switch (MOMS) tested as part of the
equipment complies with 14.6.7,
14.6.10 and 20.1.4 and meets
14.6.8 and/or 14.6.9 and Annex G
(G1.1)
Tested according to Annex G. No plastic dripping, no
flames.
flames.
P
14.6.7
Endurance test
N
14.6.8
Temperature rise in mains switch
N
14.6.9
Dielectric strength test
N
14.6.10
Surge current for mains switches
also controlling mains socket-outlets
also controlling mains socket-outlets
No socket outlets
N
-
IEC 60065, 6th edition : 1998
-
- Page 19 of 32 -
Order No. 200225249
14.7
Safety interlocks
N
Safety interlocks to 2.8 of
IEC 60 950
IEC 60 950
N
14.8
Voltage setting devices
N
Voltage setting device not likely to
be changed accidentally
be changed accidentally
N
14.9
Motors
N
14.9.1
Endurance test on motors
Low voltage disc and sliding door motors only
N
Motor start test
N
Dielectric strength test
N
14.9.2
Not adversely affected by oil or
grease etc.
grease etc.
N
14.9.3
Protection against moving parts
N
14.9.4
Motors with phase-shifting
capacitors, three-phase motors and
series motors meet Cl. B.8, B.9 and
B.10 of IEC 60 950, Annex B
capacitors, three-phase motors and
series motors meet Cl. B.8, B.9 and
B.10 of IEC 60 950, Annex B
N
14.10
Batteries
N
14.10.1
Batteries mounted with no risk of
accumulation of flammable gases
accumulation of flammable gases
N
14.10.2
No possibility of recharging non-
rechargeable batteries
rechargeable batteries
N
14.10.3
Recharging currents and times
within manufacturers limits
within manufacturers limits
N
Lithium batteries discharge and
reverse currents within the
manufacturers limits
reverse currents within the
manufacturers limits
N
14.11
Optocouplers
P
Optocouplers comply with Cl. 8
P
Internal and external dimensions to
13.1.1
13.1.1
Optocoupler Sharp PC817 is approved by Fimko
according to IEC 60950.
according to IEC 60950.
P
15
TERMINALS
P
15.1.1
Mains plug, appliance inlet,
interconnection couplers and mains
socket-outlet meet the appropriate
standard
interconnection couplers and mains
socket-outlet meet the appropriate
standard
P
Component
Manufacturer
Type
Standard
Certified
Remarks
sheet
by
(colour etc.)
Mains plug with
cord
LEONI
H03VVH2-F
IEC52
N, D, S, FI,
VDE
6A/300V Black
2x0.75mm²
Overload protection for
socket-outlets
socket-outlets
No socket outlet
N
-
IEC 60065, 6th edition : 1998
-
- Page 20 of 32 -
Order No. 200225249
15.1.2
Connectors for antenna, earth, audio, video or data:
P
No risk of insertion in mains
socket-outlets
socket-outlets
Plugs that must be used for secondary signals
connection have a design not suitable for connection to
mains sockets outlets.
connection have a design not suitable for connection to
mains sockets outlets.
P
No risk of insertion into audio or
video: outlets marked with the
symbol of 5.2 b)
video: outlets marked with the
symbol of 5.2 b)
No outlets marked with symbol
P
15.1.3
Output terminals of AC adaptors or
similar devices not compatible with
household mains socket-outlets
similar devices not compatible with
household mains socket-outlets
N
15.2
Provision for protective earthing
N
Accessible conductive parts of
Class I equipment reliably
connected to earth terminal, within
equipment
Class I equipment reliably
connected to earth terminal, within
equipment
N
Class I supply equipment with non-
hazardous live output voltage:
output circuit not connected to earth
hazardous live output voltage:
output circuit not connected to earth
N
Protective earth conductors correctly
coloured
coloured
N
Equipment with non-detachable
mains cord provided with separate
protective earth terminal near mains
input
mains cord provided with separate
protective earth terminal near mains
input
N
Protective earth terminal resistant to
corrosion
corrosion
N
Earth resistance (
Ω
) test:
≤
0,1
Ω
at
25 A
N
15.3
Terminals for external flexible cords
and for permanent connection to the
mains supply
and for permanent connection to the
mains supply
P
15.3.1
Adequate terminals for connection of
permanent wiring
permanent wiring
N
15.3.2
Reliable connection of non-detachable cords:
P
not soldered to conductors of a
printed circuit board
printed circuit board
Connected to PCB by special connector with locking
clip.
clip.
P
adequate clearances and creepage
distances between connections
should a wire break away
distances between connections
should a wire break away
See above
P
wire secured by additional means to
the conductor
the conductor
Locking clip used
P
15.3.3
Screws and nuts clamping
conductors have adequate threads:
ISO 261, ISO 262 or similar
conductors have adequate threads:
ISO 261, ISO 262 or similar
N
15.3.4
Soldered conductors wrapped
around terminal prior to soldering or
held in place by additional means
around terminal prior to soldering or
held in place by additional means
Locking clip used
N
Click on the first or last page to see other DVD 25 service manuals if exist.