Harman Kardon AVR 507 (serv.man2) EMC - CB Certificate ▷ View online
-
IEC 60065, 6th edition : 1998
-
- Page 9 of 38 -
Order
No.
11152
7.1
Operating conditions (power audio amplifier, 1/8 of maximum non clipped output):
U
=
254,4
V, I
=
1,79
A, P
=
334
W,
Pout =
2 x 8,5
W
(F)
1 x 8,4
W
(C)
2 x 7,8
W
(S)
2
x
8,9
W
(S/M)
LSL =
7 channels x 8
Ω
Ω
Ω
Ω
Loudspeaker
system(s)
Right and Left for Front,
Only one for Center,
Right and Left for Surround,
Right and Left for SB/MULTI channels.
Marking of loudspeaker terminals
FRONT, CENTER, SURROUND, SB/MULTI,
SPEAKERS ( 8
Ω
).
U =
254,4
V
6 Ohm
8 Ohm
16 Ohm
left left
right right left
right
left
right
Measured max. output voltage in Vp
F)
32,9
C) 32,8
S) 31,6
S/M) 33,8
S) 31,6
S/M) 33,8
F) 32,9
C) -
S) 31,6
S/M) 33,8
C) -
S) 31,6
S/M) 33,8
Measured max. output power in W
F)
67,6
C) 67,4
S) 62,6
S/M) 71,4
S) 62,6
S/M) 71,4
F) 67,6
C) -
S) 62,6
S/M) 71,4
C) -
S) 62,6
S/M) 71,4
Measured max. mains power in W
774
Operation of protective devices
No fuse links operate during normal operating condition
P
7.1.1
Temperature rise of accessible parts
(see table next page)
P
7.1.2
Temperature rise of parts providing
electrical insulation
electrical insulation
(see table next page)
P
7.1.3
Temperature rise of parts acting as a
support or as a mechanical barrier
support or as a mechanical barrier
(see table next page)
P
7.1.4
Temperature rise of windings
(see table next page)
P
7.1.5
Parts not subject to a limit under
7.1.1 to 7.1.4
7.1.1 to 7.1.4
(see table next page)
P
-
IEC 60065, 6th edition : 1998
-
- Page 10 of 38 -
Order
No.
11152
HEATING
∆
t = ( R2 - R1) x (234,5 + t1) - (t2 - t1)
R1
P
t1 =
27,5 °C
27,5 °C
t2 =
25,5 °C
25,5 °C
Test voltage
207 V
254,4 V
Winding
R1/
Ω
R2/
Ω
∆
t measured
∆
t allowed *
Insulation
class
class
Main transf. pr. winding (207V)
1,821
2,193
55,5
85
Class E
Sub transf. pr. winding (207V)
2892
3233
32,9
85
Class E
Main transf. pr. winding (254,4V)
1,821
2,271
66,7
85
Class E
Sub transf. pr. winding (254,4V)
2892
3383
46,5
85
Class E
Other measured parts
∆
t measured
at 207V
∆
t measured
at 254,4V
∆
t allowed *
Main transformer core
41,2
51,1
85
Sub transformer core
26,3
35,4
85
Diode, D991 body
42,7
48,6
-
Diode, D992 body
35,5
39,7
-
D992
heat-sink
36,2 40,5 -
PWB near D992
34,3
38,9
85
TR, Q803 body
48,7
60,4
-
TR, Q804 body
32,8
42,4
-
TR, Q854 body
46,6
60,1
-
PWB near Q804
43,3
55,4
85
E. Capacitor, C909 body
17,9
22,2
-
E. Capacitor, C929 body
34,8
43,3
-
IC91
heat-sink
47,6 63,6 -
Resistor, R810 body
36,4
44,6
-
Main
heat-sink
34,4 47,0 -
Fan body (on heat-sink)
29,6
37,7
60
Fan body (on back cover)
21,6
26,2
60
Power cord bushing
16,9
21,6
60
-
IEC 60065, 6th edition : 1998
-
- Page 11 of 38 -
Order
No.
11152
Other measured parts
∆
t measured
at 207V
∆
t measured
at 254,4V
∆
t allowed *
Top enclosure above main transformer
18,1
22,8
40
Top enclosure above main heat-sink
23,6
28,8
40
Power switch button
1,1
1,3
50
Comments
No other parts were observed to create any hazard due to temperature rise.
P
*) Temperature rise limits for Singapore is 10K less.
7.2
Softening temperature of insulating
material supporting parts
conductively connected to the mains
carrying a current > 0,2 A at least
150
material supporting parts
conductively connected to the mains
carrying a current > 0,2 A at least
150
°
C
No temperature measured during heating test and fault
cond. tests requires this test (7.2) to be performed.
cond. tests requires this test (7.2) to be performed.
N
Tested parts
Temperature
under normal
operating con-
ditions (°C)
under normal
operating con-
ditions (°C)
Temperature
under fault
conditions
(°C)
under fault
conditions
(°C)
Softening
temperature
(°C)
temperature
(°C)
-
IEC 60065, 6th edition : 1998
-
- Page 12 of 38 -
Order
No.
11152
8 CONSTRUCTIONAL
REQUIREMENTS WITH REGARD
TO THE PROTECTION AGAINST
ELECTRIC SHOCK
TO THE PROTECTION AGAINST
ELECTRIC SHOCK
P
8.1
Conductive parts covered by
lacquer, paper, untreated textile
oxide films and beads etc.
considered to be bare
lacquer, paper, untreated textile
oxide films and beads etc.
considered to be bare
Considered
P
8.2
Shock hazard when changing
voltage setting device, fuse-links or
handling drawers etc.
voltage setting device, fuse-links or
handling drawers etc.
Operation “By hand” not possible
N
8.3
Insulation of hazardous live parts not
provided by hygroscopic material
provided by hygroscopic material
No hygroscopic materials
N
8.4
Risk of electric shock from
accessible parts, including when
covers are removed by hand.
accessible parts, including when
covers are removed by hand.
No cover removable by hand.
N
8.5
Class I equipment
Class II equipment
N
Basic insulation between hazardous
live parts and earthed accessible
parts
live parts and earthed accessible
parts
N
Resistors bridging basic insulation
complying with 14.1 a)
complying with 14.1 a)
N
Capacitors bridging basic insulation
complying with 14.2.1 a)
complying with 14.2.1 a)
N
Basic insulation bridged by
components complying with 14.3.4.3
components complying with 14.3.4.3
N
Protective earth contact
N
8.6
Class II equipment and Class II
constructions within Class I
equipment
constructions within Class I
equipment
P
Reinforced or double insulation
between hazardous live parts and
accessible parts
between hazardous live parts and
accessible parts
Double/Reinforced insulation complies with requirements
specified in clause 10 and 13.
specified in clause 10 and 13.
P
Components bridging reinforced or
double insulation complying with
14.1 a) or 14.3
double insulation complying with
14.1 a) or 14.3
The apparatus has an isolating transformer
P
Basic and supplementary insulation
each being bridged by a capacitor
complying with 14.2.1 a)
each being bridged by a capacitor
complying with 14.2.1 a)
N
Reinforced or double insulation
being bridged by 2 capacitors in
series complying with 14.2.1 a)
being bridged by 2 capacitors in
series complying with 14.2.1 a)
N
Reinforced or double insulation
being bridged by a single capacitor
complying with 14.2.1 b)
being bridged by a single capacitor
complying with 14.2.1 b)
N
Click on the first or last page to see other AVR 507 (serv.man2) service manuals if exist.