Harman Kardon AVR 365 Service Manual ▷ View online
AVR
42
Advanced Remote Control Programming
If the message indicates that an update is available, press the front-panel ok button
4.
to begin the update.
during the update a progress bar and status messages will appear on the message
during the update a progress bar and status messages will appear on the message
5.
display. do not touch any controls on the Avr and do not interrupt the network
connection during the update.
when the update is completed the Avr will automatically power off, and after five
when the update is completed the Avr will automatically power off, and after five
6.
seconds will automatically power back on. once the Avr turns back on it’s ready to
use.
Resetting the Remote
to reset the remote to its factory default condition, simultaneously press and hold the tv
Source Selector button and the “0” number button. when the tv Source button relights,
enter the code “333.” when the tv button goes out, and all of the Source Selector buttons
flash, the remote control will be reset.
Processor Reset
If the Avr behaves erratically after a power surge, first turn off the rear-panel main
power switch and unplug the Ac power cord for at least 3 minutes. plug the cord back
in and turn the receiver on. If this procedure doesn’t help, reset the Avr’s processor as
described below.
NOTE: A processor reset erases all user configurations, including video resolution,
NOTE: A processor reset erases all user configurations, including video resolution,
speaker and level settings, and tuner presets. After a reset, reenter all of these settings
from your notes in the Appendix worksheets.
To reset the AVR’s processor:
To reset the AVR’s processor:
press the front-panel Standby/on switch to place the unit in the Standby mode (the
1.
power Indicator will turn amber).
press and hold the front-panel ok button for at least 5 seconds until the reSet
press and hold the front-panel ok button for at least 5 seconds until the reSet
2.
message appears on the front-panel message display.
NOTE: After performing a processor reset, wait at least 1 minute before pressing any
Source Selector buttons.
If the receiver does not function correctly after a processor reset, contact an authorized
If the receiver does not function correctly after a processor reset, contact an authorized
harman kardon service center for assistance. Authorized service centers may be located
by visiting our web site at www.harmankardon.com.
Harman Kardon
AVR 365/230V Service Manual
Page 13 of 176
AVR
43
ENGL
IS
H
Troubleshooting
Symptom
Cause
Solution
unit does not function when main power switch is turned
on
no Ac power
•
ensure that the power cord is plugged into a live Ac
•
power outlet
check if the Ac outlet is switch-controlled
check if the Ac outlet is switch-controlled
•
front-panel message display lights, but there’s no sound
or picture
Intermittent input connection
•
mute is on
•
volume control is turned down
•
Secure all input and speaker connections
•
press mute button
•
turn up volume control
•
no sound from any speaker; protect message appears
on message display
Amplifier is in protection mode due to possible short
•
circuit
Amplifier is in protection mode due to internal problems
Amplifier is in protection mode due to internal problems
•
check all speaker wires at speaker and Avr
•
connections for crossed wires
contact your local harman kardon service center
contact your local harman kardon service center
•
no sound from center or surround speakers
Incorrect surround mode
•
program material is monophonic
•
Incorrect speaker configuration
•
program material is stereo
•
Select a surround mode other than stereo
•
mono programs contain no surround information
•
check the speaker configuration in the setup menu
•
the surround decoder may not create center- or
•
surround-channel information from nonencoded
programs
unit does not respond to remote control commands
weak batteries in remote
•
Avr not selected
•
remote sensor is obscured
•
change batteries in remote
•
press the Setup/Avr button
•
ensure that the Avr’s front-panel remote sensor is in
•
the line of sight of the remote
Intermittent buzzing in tuner
local interference
•
move the Avr or antenna away from computers,
•
fluorescent lights, motors or other electrical appliances
(AVR 3650/AVR 365 only): Surround-back speaker
settings cannot be accessed, and the test tone does not
play through the surround back speakers
multi-zone operation has been selected/Assigned Amp
•
channels have been assigned to Zone 2
use the Speaker Setup menu to reassign the Assigned
•
Amp to the surround back left and right channels
(AVR 3650/AVR 2650 only): the SIrIuS preview
channel (001) is silent
SIrIuS tuner is not connected
•
SIrIuS antenna is in an improper location
•
SIrIuS signal requires a refresh
•
ensure that SIrIuS tuner is properly connected
•
re-locate the SIrIuS antenna according to the
•
recommendations in the SIrIuS tuner’s instruction
manual. for further help, visit
www.siriusradio.com
visit www.siriusradio.com
visit www.siriusradio.com
•
unable to activate remote control programming mode
Source Selector button is not held for at least 3
•
seconds
be sure to hold the Source Selector button for at least
•
3 seconds
remote buttons light, but Avr does not respond
remote is in Zone 2 mode
•
Slide Zone Selector switch to the Zone 1 position.
•
unable to establish network connection
Avr network programming requires rebooting
•
cycle the Avr into the Standby mode, and then turn it
•
on again
Additional information on troubleshooting possible problems with your Avr and installation-related issues may be found in the list of “frequently Asked questions,” which is
located in the product Support section of our web site: www.harmankardon.com
Harman Kardon
AVR 365/230V Service Manual
Page 14 of 176
AVR
44
Specifications
Audio Section
Stereo power:
Avr 3650/Avr 365: 110w per channel, two
channels driven @ 8 ohms, 20hz – 20khz,
<0.09% thd
Avr 2650/Avr 265: 95w per channel, two
Avr 2650/Avr 265: 95w per channel, two
channels driven @ 8 ohms, 20hz – 20khz,
<0.09% thd
multichannel power:
Avr 3650/Avr 365: 110w per channel, two
channels driven @ 8 ohms, 20hz – 20khz,
<0.09% thd
Avr 2650/Avr 265: 95w per channel, two
Avr 2650/Avr 265: 95w per channel, two
channels driven @ 8 ohms, 20hz – 20khz,
<0.09% thd
Input sensitivity/impedance:
200mv/47k ohms
Signal-to-noise ratio (Ihf-A):
100db
Surround system adjacent channel
separation:
dolby pro logic/dplII: 40db
dolby digital: 55db
dtS: 55db
dolby digital: 55db
dtS: 55db
frequency response (@ 1w):
10hz – 130khz (+0db/–3db)
high instantaneous current capability
(hcc):
±35 amps
transient intermodulation distortion
(tIm):
unmeasurable
Slew rate:
40v/μsec
FM Tuner Section
frequency range:
87.5 – 108.0mhz
usable sensitivity Ihf:
1.3μv/13.2dbf
Signal-to-noise ratio (mono/stereo):
70db/68db
distortion (mono/stereo):
0.2%/0.3%
Stereo separation:
40db @ 1khz
Selectivity (±400khz):
70db
Image rejection:
80db
If rejection:
90db
AM Tuner Section
frequency range:
520 – 1710khz (Avr 3650/Avr 2650)
522 – 1620khz (Avr 365/Avr 265)
522 – 1620khz (Avr 365/Avr 265)
Signal-to-noise ratio:
45db
usable sensitivity (loop):
500μv
distortion (1khz, 50% mod):
0.8%
Selectivity (±10khz):
30db
Video Section
television format:
ntSc (Avr 3650/Avr 2650);
pAl (Avr 365/Avr 265)
Input level/impedance:
1vp-p/75 ohms
output level/impedance:
1vp-p/75 ohms
video frequency response (composite
video):
10hz – 8mhz (–3db)
hdmI:
version 1.4a with 12-bit deep color
General Specifications
power requirement:
120v Ac/60hz (Avr 3650/Avr 2650);
220v – 240v Ac/50hz – 60hz (Avr 365/
Avr 265)
power consumption:
<0.5w (standby);
480w maximum (Avr 3650/Avr 365);
420w maximum (Avr 2650/Avr 265)
dimensions (w x h x d):
17-5/16" x 6-1/2" x 17-1/8"
(440mm x 165mm x 435mm)
weight
(Avr 3650/Avr 365): 27.25 lb (12.4kg)
(Avr 2650/Avr 265): 24.4 lb (11.1kg)
(Avr 2650/Avr 265): 24.4 lb (11.1kg)
depth measurement includes knobs, buttons and terminal connections.
height measurement includes feet and chassis.
Specifications
Harman Kardon
AVR 365/230V Service Manual
Page 15 of 176
AVR
45
ENGL
IS
H
Table A2 – Source Setting Defaults
Appendix – Default settings, worksheets, remote product codes
Table A1 – Recommended Source Component Connections
Cable/Sat
Blu-ray
Media
Server
Radio
TV
Game
AUX
The Bridge
DVR
(AVR 2650/
AVR 265 only)
USB
(AVR 3650/
AVR 365 only)
Surround modes
(Auto Select)
logic 7
movie
logic 7
movie
logic 7
movie
logic 7
movie
logic 7 movie
logic 7
movie
logic 7 music
logic 7 music logic 7 movie
Stereo
video Input
hdmI 2
hdmI 1
hdmI 4
n/A
hdmI 5 (Avr
3650/Avr 365);
hdmI 1 (Avr
2650/Avr 265)
hdmI 3
hdmI front (Avr
3650/Avr 365);
n/A (Avr 2650/
Avr 265)
the bridge III
hdmI 5
n/A
Audio Input
hdmI 2
hdmI 1
hdmI 4
n/A
hdmI 5 (Avr
3650/Avr 365);
hdmI 1 (Avr
2650/Avr 265)
hdmI 3
hdmI front (Avr
3650/Avr 365);
Analog 2 (Avr
2650/Avr 265)
the bridge III
hdmI 5
n/A
resolution to
display*
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
480i (ntSc);
576p (pAl)
Audio Auto polling off
off
off
n/A
off
off
off
n/A
off
n/A
Zone 2 Audio
—
—
—
radio
—
—
Analog 2
the bridge III
—
uSb
dolby volume
medium
low
medium
medium
medium
medium
low
medium
medium
medium
* video output resolution may vary for hdmI connections. the default hdmI resolution is 1080i for ntSc and pAl.
Device Type
AVR Source
Digital Audio Connection
Analog Audio Connection
Video Connections
cable tv, satellite tv, hdtv
or other device that delivers
television programs
cable/SAt
hdmI 2
Analog 1, 2 or 3
hdmI 2
dvd Audio/video, SAcd,
blu-ray disc, hd-dvd player
blu-ray
hdmI 1
Analog 1, 2 or 3
hdmI 1
media Server, including
harman kardon dmc 1000
media Server
hdmI 4
Analog 1, 2 or 3
hdmI 4
tv
tv
hdmI 5 (Avr 3650/Avr 365);
hdmI 1 (Avr 2650/Avr 265)
Analog 1, 2 or 3
hdmI 5 (Avr 3650/Avr 365);
hdmI 1 (Avr 2650/Avr 265)
video-game console
game
hdmI 3 (or hdmI front on
Avr 3650/Avr 365)
Analog 1, 2 or 3 4
hdmI 3 (or hdmI front on
Avr 3650/Avr 365)
Any audio or video device,
e.g., cd player, camcorder,
cassette deck
Aux
coaxial or optical
Analog 1, 2 or 3
composite video 1 or 2 (not used
for audio-only devices)
recorder
Any
coaxial or optical Input and
optical output
Analog 1, 2 or 3 Inputs and rec
out
composite video 2 Input and
output
ipod or iphone
the bridge IIIp
none
the bridge IIIp
the bridge IIIp for photo- and
video-capable ipod and iphone
models
dvr
(Avr 2650/Avr 265 only)
dvr
hdmI 5
Analog 1, 2 or 3
hdmI 5
Appendix
Harman Kardon
AVR 365/230V Service Manual
Page 16 of 176
Click on the first or last page to see other AVR 365 service manuals if exist.