Harman Kardon AVR 340 (serv.man11) EMC - CB Certificate ▷ View online
-
IEC 60065, 6th edition : 1998
-
- Page 30 of 39 -
Order
No.
51563
18
MECHANICAL STRENGTH OF
PICTURE TUBES AND
PROTECTION AGAINST THE
EFFECTS OF IMPLOSION
PICTURE TUBES AND
PROTECTION AGAINST THE
EFFECTS OF IMPLOSION
N
18.1
Picture tube separately approved
No picture tube
N
Picture tubes > 16 cm intrinsically
protected
protected
N
Non-intrinsically protected tubes
> 16 cm used with protective
screen
> 16 cm used with protective
screen
N
18.2
Intrinsically protected tubes: tests
on 12 samples
on 12 samples
N
18.2.1
Samples subject to ageing: 6
N
18.2.2
Samples subject to implosion test:
6
6
N
18.2.3
Samples subject to mechanical
strength test (steel ball): 6
strength test (steel ball): 6
N
18.3
Non-intrinsically protected tubes
tested to 18.3
tested to 18.3
N
19
STABILITY AND MECHANICAL
HAZARDS
HAZARDS
P
Mass of the equipment exceeding
18 kg
18 kg
Mass < 18 kg.
N
19.1
Test on a plane, inclined at 10
° to
the horizontal
N
19.2
100 N force applied vertically
downwards
downwards
N
19.3
Smooth edges and corners
There is no hazardous edges or corners when the
apparatus is operating in normal position
apparatus is operating in normal position
P
19.4
Glass surfaces with an area
exceeding 0,1 m² or maximum
dimension > 450 mm, pass the test
of 19.4.1
exceeding 0,1 m² or maximum
dimension > 450 mm, pass the test
of 19.4.1
No glass surface.
N
20
RESISTANCE TO FIRE
P
20.1
Electrical components and
mechanical parts
mechanical parts
P
Apparatus
design
Resistance to fire is achieved by a combination of
engineering design, production methods and by using
materials with low flammability for internal parts
engineering design, production methods and by using
materials with low flammability for internal parts
P
-
IEC 60065, 6th edition : 1998
-
- Page 31 of 39 -
Order
No.
51563
a) Exemption for components
contained in an enclosure of
material FV 0 to IEC 60 707 with
openings not exceeding 1 mm in
width
contained in an enclosure of
material FV 0 to IEC 60 707 with
openings not exceeding 1 mm in
width
N
b) Exemption for small components
as defined in 20.1
as defined in 20.1
PCB is of flammability class FV 1 or better, and
exception is made for small components.
exception is made for small components.
N
20.1.1
Electrical components meet the
requirements of 14.2.5, 14.4, 14.5.3
or 14.6.6
requirements of 14.2.5, 14.4, 14.5.3
or 14.6.6
No other electrical components with additional
flammability requirements.
flammability requirements.
N
20.1.2
Insulation of internal wiring working
at voltages > 4 kV or leaving an
internal fire enclosure, not
contributing to the spread of fire
at voltages > 4 kV or leaving an
internal fire enclosure, not
contributing to the spread of fire
No wires working at voltages > 4kV or leaving an internal
fire enclosure
fire enclosure
N
20.1.3
Material of printed circuit boards on
which the available power exceeds
15 W at a voltage between 50 V
and 400 V (peak) a.c. or d.c. meets
FV 1 or better to IEC 60 707,
unless used in a fire enclosure
which the available power exceeds
15 W at a voltage between 50 V
and 400 V (peak) a.c. or d.c. meets
FV 1 or better to IEC 60 707,
unless used in a fire enclosure
All PCB are of base material with flammability category
FV 0. See List of Critical Components
FV 0. See List of Critical Components
P
Material of printed circuit boards on
which the available power exceeds
15 W at a voltage exceeding 400 V
(peak) a.c. or d.c. meets FV 0 to
IEC 60 707
which the available power exceeds
15 W at a voltage exceeding 400 V
(peak) a.c. or d.c. meets FV 0 to
IEC 60 707
N
20.1.4
Components and parts not covered
by 20.1.1, 20.1.2 and 20.1.3 (other
than fire enclosures) mounted
nearer to a potential ignition source
than the distances in Table 13
comply with the relevant
flammability category in Table 13
by 20.1.1, 20.1.2 and 20.1.3 (other
than fire enclosures) mounted
nearer to a potential ignition source
than the distances in Table 13
comply with the relevant
flammability category in Table 13
N
Components and parts as above
but shielded from a potential
ignition source, with the barrier area
in accordance with Table 13 and
fig. 13
but shielded from a potential
ignition source, with the barrier area
in accordance with Table 13 and
fig. 13
N
20.2 Fire
enclosure
N
20.2.1
Potential ignition sources with open
circuit voltage > 4 kV (peak) a.c. or
d.c. contained in a fire enclosure to
FV 1
circuit voltage > 4 kV (peak) a.c. or
d.c. contained in a fire enclosure to
FV 1
No voltages exceeding 4kV, no fire enclosure
requirement.
requirement.
N
20.2.2
Internal fire enclosures with
openings not exceeding 1 mm in
width and with openings for wires
completely filled
openings not exceeding 1 mm in
width and with openings for wires
completely filled
N
20.2.3 Requirements
of 20.2.1 and 20.2.2
met by an internal fire enclosure
N
-
IEC 60065, 6th edition : 1998
-
- Page 32 of 39 -
Order
No.
51563
A
ANNEX A, ADDITIONAL
REQUIREMENTS FOR
APPARATUS WITH PROTECTION
AGAINST SPLASHING WATER
REQUIREMENTS FOR
APPARATUS WITH PROTECTION
AGAINST SPLASHING WATER
N
A.5.1
j) Marked with IPX4 (IEC 60 529),
5.4.1 a) does not apply
5.4.1 a) does not apply
Not intended for outdoor use.
N
A.10.2.1
Enclosure provides protection
against splashing water
against splashing water
N
A.10.2.2
Humidity treatment carried out for
7 days
7 days
N
B
ANNEX B, APPARATUS TO BE
CONNECTED TO THE
TELECOMMUNICATION
NETWORKS
CONNECTED TO THE
TELECOMMUNICATION
NETWORKS
N
B.5.4.1
e) Where the separation of TNV
circuits from other circuits relies on
protective earthing the instructions
make it clear that protective earthing
is essential
circuits from other circuits relies on
protective earthing the instructions
make it clear that protective earthing
is essential
No intended for telecommunication networks.
N
B.8.1
TNV circuits separated from the
mains circuit and from hazardous
live parts by either:
mains circuit and from hazardous
live parts by either:
N
a) double or reinforced insulation
N
b) basic insulation with earthed
protective screening
protective screening
N
B.8.2
TNV circuits separated from circuits
other than those in B.8.1 and from
accessible conductive parts by basic
insulation meeting the requirements
for clearances and creepage
distances for the voltages
concerned
other than those in B.8.1 and from
accessible conductive parts by basic
insulation meeting the requirements
for clearances and creepage
distances for the voltages
concerned
N
B.9.1.1
TNV circuit terminals contacts which
cannot be touched by probe B.1,
exempt from the requirements
inaccessible terminal contacts in
9.1.1
cannot be touched by probe B.1,
exempt from the requirements
inaccessible terminal contacts in
9.1.1
N
B.10.1
Insulation between TNV terminals
and antenna terminals (including
interconnection terminals which may
be connected to equipment with
antenna terminals) withstands the
50 discharges of 10.1
and antenna terminals (including
interconnection terminals which may
be connected to equipment with
antenna terminals) withstands the
50 discharges of 10.1
N
B.14.12
Surge suppressors between TNV
circuits and other parts of the
equipment have breakdown voltage
at least 1,8 times the mains voltage
circuits and other parts of the
equipment have breakdown voltage
at least 1,8 times the mains voltage
N
-
IEC 60065, 6th edition : 1998
-
- Page 33 of 39 -
Order
No.
51563
LIST OF CRITICAL COMPONENTS (continued)
Part No
Component/
Object
Object
Manufacturer
Type / Model
Ratings /
Technical Data
Technical Data
Complies
with the
following
standard
with the
following
standard
Marks of
conformity
granted **
conformity
granted **
For
CENELEC
Countries
CENELEC
Countries
Mains plug
with cord
with cord
Kenic Electric Mfg.
KE-25
H03VVH2-F
H03VVH2-F
10-16A/250V
6A/250V
6A/250V
IEC60884-1
VDE
alt
Volex (Asia) Pte.
Ltd.
Ltd.
M3204
H03VVH2-F
H03VVH2-F
10-16A/250V
6A/250V
6A/250V
IEC60884-1
VDE
alt
HWAJIN KDK Co.
KKP-4819C
H03VVH2-F
H03VVH2-F
10-16A/250V
6A/250V
6A/250V
IEC60884-1
VDE
For U.K.
Mains plug
with cord
with cord
Volex (Asia) Pte Ltd.
MP5005
H03VVH2-F
H03VVH2-F
13A/250V
6A/250V
6A/250V
BS1363
BS6500
BS6500
ASTA
alt
Volex (Asia) Pte Ltd.
MP5004A
H03VVH2-F
H03VVH2-F
13A/250V
6A/250V
6A/250V
BS1363
BS6500
BS6500
ASTA
alt
PHINO
Electronics
Co., Ltd
PHP-307F
H03VVH2-F
H03VVH2-F
13A/250V
6A/250V
6A/250V
BS1363
BS6500
BS6500
BSI
alt
Winbo Industries
MS 323N
H03VVH2-F
H03VVH2-F
13A/250V
6A/250V
6A/250V
BS1363
BS6500
BS6500
BSI
alt
Luen Tai (IP`S) Elect.
Kenic Electric Mfg.
Kenic Electric Mfg.
9518
H03VVH2-F
H03VVH2-F
13A/250V
6A/250V
6A/250V
BS1363
BS6500
BS6500
BSI
alt
Well shin Enterprise
Co. Ltd.
Co. Ltd.
WS-012A
H03VVH2-F
H03VVH2-F
13A/250V
6A/250V
6A/250V
BS1363
BS6500
BS6500
BSI
OL91 Mains
Socket-outlet
Dae Ryung
Electronics.
Electronics.
A3-04-D007 2.5A/250V
IEC60884-1
NEMKO
SW1
Mains switch
POSTEC Electric. SDL1P-B 5A/80A
250V
IEC60065
IEC61058-1
IEC61058-1
VDE
RY94
Mains relay
Tyco Electronics
SDT-S-112DMR
8A/120A 250V
IEC60065
IEC61058-1
IEC61058-1
SEMKO
- Mains
transformer
Bobbin Mti.
Thermal fuse
Bobbin Mti.
Thermal fuse
Seoul Electronics &
Telecom Co., Ltd.
Wintech Ploymer Ltd.
Micro Devices.
Telecom Co., Ltd.
Wintech Ploymer Ltd.
Micro Devices.
KLT5W022ZE
CLT5W022ZE
CN9030
E4A51167C
CLT5W022ZE
CN9030
E4A51167C
230V Class B
V-0, 155°C
V-0, 155°C
10A/250V 167°C
IEC60065
clause 14.3
UL94
IEC60691
clause 14.3
UL94
IEC60691
1.)
UL E213445
VDE
UL E213445
VDE
- Sub
transformer
Bobbin Mti.
Thermal fuse
Bobbin Mti.
Thermal fuse
Seoul Electronics &
Telecom Co., Ltd.
LG Chemical Ltd..
Anzen Dengu Co., Ltd.
Telecom Co., Ltd.
LG Chemical Ltd..
Anzen Dengu Co., Ltd.
KLT5J038ZE
CLT5J038ZE
GP2306F(#)
K11
CLT5J038ZE
GP2306F(#)
K11
230V Class E
V-0, 140°C
V-0, 140°C
1A/250V, 115°C
IEC60065
clause 14.3
UL94
IEC60691
clause 14.3
UL94
IEC60691
1.)
UL E67171
VDE
UL E67171
VDE
**) Marks listed under “Marks of conformity granted” indicates that Nemko has verified certifications respectively
1.) Tested as part of the Apparatus according to EN 60 065 / IEC 60065, 6 Edition :1998
Click on the first or last page to see other AVR 340 (serv.man11) service manuals if exist.