Sony SLV-SE740B / SLV-SE740D / SLV-SE740E / SLV-SE740G / SLV-SE740I / SLV-SE740N / SLV-SE747E / SLV-SE840B / SLV-SE840D / SLV-SE840E / SLV-SE840G / SLV-SE840N / SLV-SX740D / SLV-SX740E / SLV-SX740N Service Manual ▷ View online
2-6
2-2-2 Bottom View
1 2
3
4
5
6
7
8
9
q;
1
GEAR JOINT 1
2
GEAR JOINT 2
3
BRAKET GEAR
4
MOTOR CAPSTAN ASS’Y
5
LEVER T LOAD ASS’Y
6
GEAR LOADING DRIVE
7
LEVER S LOAD ASS’Y
8
HOLDER CLUTCH ASS’Y
9
BELT PULLEY
q;
SLIDER CAM
Fig. 2-8 Bottom Parts Location
2-7
"B"
"A"
1
LEVER FL DOOR
2
HOOK
2-3 VCR DECK
2-3-1 Holder FL Cassette Ass’y Removal
1) Pull the Holder FL Cassette Ass’y 1 to the eject position.
2) Pull the Holder FL Cassette Ass’y 1 as grasping the Holder FL
2) Pull the Holder FL Cassette Ass’y 1 as grasping the Holder FL
Cassette Ass’y 1 and Lever FL Cassette-R 2 in the same time to
release hooking from Main Base until the Boss [A] of Holder FL
Cassette Ass’y 1 is taken out from the Rail [B].
release hooking from Main Base until the Boss [A] of Holder FL
Cassette Ass’y 1 is taken out from the Rail [B].
3) Lift the Holder FL Cassette Ass’y 1, in this time, you have to
grasp the Lever FL Cassette-R 2 Continuously until the Holder
FL Cassette Ass’y 1 is taken out completely.
FL Cassette Ass’y 1 is taken out completely.
Note:
Be sure to insert Lever FL Cassette-R 2 in the direction of
“A” to prevent separation and breakage of the Lever FL Cassette-R 2
at disassembling and reassembling.
at disassembling and reassembling.
Fig. 2-9 Holder FL Cassette Ass’y Removal
2-3-2 Lever FL Door Removal
1) Release the Hook 2 and Remove the Lever FL Door 1 in the
direction of arrow “A”.
Fig. 2-10 Lever FL Door Removal
1
HOLDER FL
CASSETTEE ASS'Y
CASSETTEE ASS'Y
BOSS [A]
RAIL [B]
2
LEVER FL CASSETTEE -R
"A"
2-8
1
SLIDER FL DRIVE
2
GEAR FL CAM
2-3-3 Slider FL Drive, Gear FL Cam Removal
1) Pull the Slider FL Drive 1 to the front direction.
2) Remove the Slider FL Drive 1 in the direction of arrow. (Refer to
2) Remove the Slider FL Drive 1 in the direction of arrow. (Refer to
Fig. 2-11)
3) Remove the Gear FL cam 2.
Note:
When reinstalling be sure to reassemble Slider FL drive 1
after you insert the Boss of Lever FL ARM-R in Groove of Slider FL
drive 1.
drive 1.
Assembly:
Align the Gear FL Cam 1 with the Gear worm wheel
Post as shown drawing.
(Refer to Timing point)
(Refer to Timing point)
Fig. 2-11 Slider FL Drive Removal
Fig. 2-12 Gear FL Cam, Gear Worm
2-3-4 Lever FL Arm Ass’y Removal
1) Push the hole “A” in the direction of arrow “B” use the pin.(about
Dia. 2.5)
2) Pull out the Lever FL Arm Ass’y 1 from the Boss of Main Base.
3) Remove the Lever FL Arm Ass’y 1 in the direction of arrow “C”.
3) Remove the Lever FL Arm Ass’y 1 in the direction of arrow “C”.
Fig. 2-13 Lever FL Arm Ass’y Removal
1
GEAR FL CAM
GEAR WORM WHEEL
POST
TIMING POINT
1
LEVER FL ARM ASS'Y
"C"
"B"
PIN
HOLE "A"
2-9
3
CONNECTOR WAFER
2
CONNECTOR WAFER
1
CABLE FLAT
1
GEAR WORM WHEEL
2-3-5 Gear Worm Wheel Removal
1) Remove the Gear Worm wheel 1.
Fig. 2-14 Gear Worm Wheel Removal
2-3-6 Cable Flat Removal
1) Remove the Drum connecting part of Cable Flat 1 from Connector
Waffer 2.
2) Remove the Loading Motor connecting part of Cable Flat 1 from
Connector Waffer 3.
Fig. 2-15 Cable Flat Removal
Click on the first or last page to see other SLV-SE740B / SLV-SE740D / SLV-SE740E / SLV-SE740G / SLV-SE740I / SLV-SE740N / SLV-SE747E / SLV-SE840B / SLV-SE840D / SLV-SE840E / SLV-SE840G / SLV-SE840N / SLV-SX740D / SLV-SX740E / SLV-SX740N service manuals if exist.