Sony SLV-D920B / SLV-D920E / SLV-D920N / SLV-D920R / SLV-D925E / SLV-D930D / SLV-D930GI / SLV-D960PB / SLV-D960PE Service Manual ▷ View online
2-7
2-4 VCR DECK
2-4-1 Holder FL Cassette Ass’y Removal
1) Pull the Holder FL Cassette Ass’y 1 to the eject position.
2) Pull the Holder FL Cassette Ass’y 1 as grasping the Holder FL
2) Pull the Holder FL Cassette Ass’y 1 as grasping the Holder FL
Cassette Ass’y 1 and Lever FL Cassette-R 2 in the same time to
release hooking from Main Base until the Boss [A] of Holder FL
Cassette Ass’y 1 is taken out from the Rail [B].
release hooking from Main Base until the Boss [A] of Holder FL
Cassette Ass’y 1 is taken out from the Rail [B].
3) Lift the Holder FL Cassette Ass’y 1, in this time, you have to
grasp the Lever FL Cassette-R 2 Continuously until the Holder
FL Cassette Ass’y 1 is taken out completely.
FL Cassette Ass’y 1 is taken out completely.
Note:
Be sure to insert Lever FL Cassette-R 2 in the direction of
“A” to prevent separation and breakage of the Lever FL Cassette-
R 2 at disassembling and reassembling.
R 2 at disassembling and reassembling.
Fig. 2-11 Holder FL Cassette Ass’y Removal
RAIL [B]
BOSS [A]
2
LEVER FL CASSETTEE -R
"A"
1
HOLDER FL
CASSETTEE ASS'Y
CASSETTEE ASS'Y
2-4-2 Lever FL Door Removal
1) Release the Hook 2 and Remove the Lever FL Door 1 in the
direction of arrow “A”.
Fig. 2-12 Lever FL Door Removal
"B"
"A"
1
LEVER FL DOOR
2
HOOK
2-8
2-4-3 Slider FL Drive, Gear FL Cam Removal
1) Pull the Slider FL Drive 1 to the front direction.
2) Remove the Slider FL Drive 1 in the direction of arrow. (Refer to
2) Remove the Slider FL Drive 1 in the direction of arrow. (Refer to
Fig. 2-13)
3) Remove the Gear FL cam 2.
Note:
When reinstalling be sure to reassemble Slider FL drive 1
after you insert the Boss of Lever FL ARM-R in Groove of Slider FL
drive 1.
drive 1.
Assembly:
Align the Gear FL Cam 1 with the Gear worm wheel
Post as shown drawing.
(Refer to Timing point)
(Refer to Timing point)
Fig. 2-13 Slider FL Drive, Gear FL Cam Removal
Fig. 2-14 Gear FL Cam, Gear Worm
1
GEAR FL CAM
GEAR WORM WHEEL
POST
TIMING POINT
1
SLIDER FL DRIVE
2
GEAR FL CAM
2-4-4 Lever FL Arm Ass’y Removal
1) Push the hole “A” in the direction of arrow “B” use the pin.(about
Dia. 2.5)
2) Pull out the Lever FL Arm Ass’y 1 from the Boss of Main Base.
3) Remove the Lever FL Arm Ass’y 1 in the direction of arrow “C”.
3) Remove the Lever FL Arm Ass’y 1 in the direction of arrow “C”.
Fig. 2-15 Lever FL Arm Ass’y Removal
1
LEVER FL ARM ASS'Y
"C"
"B"
PIN
HOLE "A"
2-9
2
CONNECTOR WAFER
1
CABLE FLAT
3
CONNECTOR WAFER
2-4-5 Gear Worm Wheel Removal
1) Remove the Gear Worm wheel 1.
Fig. 2-16 Gear Worm Wheel Removal
2-4-6 Cable Flat Removal
1) Remove the Drum connecting part of Cable Flat 1 from Connector
Wafer 2.
2) Remove the Loading Motor connecting part of Cable Flat 1 from
Connector Wafer 3.
Fig. 2-17 Cable Flat Removal
1
GEAR WORM WHEEL
2-10
1
SCREW
2
BRAKET GEAR
4
GEAR JOINT 1
3
GEAR JOINT 2
2
MOTOR LOADING ASS`Y
1
SCREW
2-4-7 Motor Loading Ass’y Removal
1) Remove the Screw 1.
2) Remove the Motor Loading Ass’y 2.
2) Remove the Motor Loading Ass’y 2.
Fig.2-18 Motor Loading Ass’y Removal
2-4-8 Bracket Gear, Gear Joint 2, 1 Removal
1) Remove the Screw 1.
2) Remove the Bracket Gear 2.
3) Remove the Gear Joint 2 3.
4) Remove the Gear Joint 1 4.
2) Remove the Bracket Gear 2.
3) Remove the Gear Joint 2 3.
4) Remove the Gear Joint 1 4.
Assembly:
1) Be sure to align dot mark of Gear Joint 1 1 with dot mark of
Gear Joint 2 2 as shown Fig 2-20.
(Refer to Timing point1)
(Refer to Timing point1)
2) Confirm the Timing Point 2 of the Gear Joint 2 2 and Slider
Cam 3.
Fig. 2-19 Bracket Gear, Gear Joint 1,2 Removal
Fig. 2-20 Gear Joint 1,2 Assembly
1
GEAR JOINT1
2
GEAR JOINT2
3
SLIDER CAM
TIMING POINT 1
TIMING POINT 2
Click on the first or last page to see other SLV-D920B / SLV-D920E / SLV-D920N / SLV-D920R / SLV-D925E / SLV-D930D / SLV-D930GI / SLV-D960PB / SLV-D960PE service manuals if exist.