Sony SLV-D920B / SLV-D920E / SLV-D920N / SLV-D920R / SLV-D925E / SLV-D930D / SLV-D930GI / SLV-D960PB / SLV-D960PE Service Manual ▷ View online
2-15
1
GUIDE CASSETTE DOOR
HOOK [A]
2-4-17 Lever Up Down Ass’y, Gear Center
Ass’y Removal
1) Remove the 2 hooks in the direction of arrow as shown Fig. 2-29
and lift the Lever Up Down Ass’y 1.
2) Lift the Gear Center Ass’y 2.
Assembly:
1) Insert the Lever Up Down Ass’y 1 in the rectangular holes on
Main Base as shown in Fig 2-30.
2) Lift the Lever Up Down Ass’y 1 about 35
°
.
(Refer to Fig 2-30)
3) Insert Ring of the Gear Center Ass’y 2 in the Guide of the Lever
3) Insert Ring of the Gear Center Ass’y 2 in the Guide of the Lever
Up Down Ass’y 1.
4) Insert the Gear Center Ass’y 2 in the post on Main Base.
5) Push down the Lever Up Down Ass’y 1 for locking of the Hook.
5) Push down the Lever Up Down Ass’y 1 for locking of the Hook.
Note:
1) Take care not to separate and sentence does not mark sense.
2) Be sure to confirm that Ring of the Gear Center Ass’y 2 is in the
2) Be sure to confirm that Ring of the Gear Center Ass’y 2 is in the
Guide of the Lever Up Down Ass’y 1 after finishing assembly of
Lever Up Down Ass’y 1 and Gear Center Ass’y 2.
Lever Up Down Ass’y 1 and Gear Center Ass’y 2.
Fig. 2-29 Lever Up Down Ass’y Removal
Fig. 2-30 Lever Up Down Ass’y Assembly
2-4-18 Guide Cassette Door Removal
1) Lift the Hook [A].
2) Rotate the Guide Cassette Door 1 in the direction of arrow.
2) Rotate the Guide Cassette Door 1 in the direction of arrow.
Note:
After reinstalling the Guide Cassette Door 1 sure the Hook
[A].
Fig. 2-31 Guide Cassette Door Removal
1
LEVER UP DOWN ASS`Y
2
GEAR CENTER ASS`Y
MAIN BASE
1
LEVER UP DOWN ASS'Y
GUIDE
2
GEAR CENTER ASS'Y
RING
GEAR
POST
POST
HOOK
35
2-16
1
SPRING #9 GUIDE
2
LEVER #9 GUIDE ASS`Y
"B"
"A"
3
SPRING PINCH DRIVE
1
LEVER UNIT PINCH ASS`Y
2
PLATE JOINT
2-4-19 Lever Unit Pinch Ass’y, Plate Joint,
Spring Pinch Drive Removal
1) Lift the Lever Unit Pinch Ass’y 1.
2) Remove the Plate Joint 2 from Lever Pinch Drive.
3) Remove the Spring Pinch Drive 3.
2) Remove the Plate Joint 2 from Lever Pinch Drive.
3) Remove the Spring Pinch Drive 3.
Note:
1) Take extreme care not to touch the grease on the Roller Pinch.
2) When reinstalling, be sure to apply grease on the post pinch roller.
2) When reinstalling, be sure to apply grease on the post pinch roller.
Fig. 2-32 Lever Unit Pinch Ass’y, Plate Joint,
Spring Pinch Drive Removal
2-4-20 Lever #9 Guide Ass’y Removal
1) Remove the Spring #9 Guide 1.
2) Lift the Lever #9 Guide Ass’y 2 in the direction of arrow “A”.
2) Lift the Lever #9 Guide Ass’y 2 in the direction of arrow “A”.
Note:
1) Take extreme care not to get grease on the tape Guide Post.
2) After reinstalling, check the bottom side of the Post #9 Guide to
2) After reinstalling, check the bottom side of the Post #9 Guide to
the top side of Main Base.
Fig. 2-33 Lever #9 Guide Ass’y Removal
2-17
1
SCREW
2
ACE HEAD ASS'Y
1
FE HEAD
2-4-21 FE Head Removal
1) Lift the FE Head 1.
Fig. 2-34 FE Head Removal
2-4-22 ACE Head Removal
1) Pull out the FPC from connector of ACE Head Ass’y 2.
2) Remove the Screw 1.
3) Lift the ACE Head Ass’y 2.
2) Remove the Screw 1.
3) Lift the ACE Head Ass’y 2.
Fig. 2-35 ACE Head Removal
2-18
1
SLIDER S ASS'Y
2
SLIDER T ASS'Y
1
3 SCREWS
2
PLATE GROUND DECK
3
CYLINDER ASS'Y
2-4-23 Slider S, T Ass’y Removal
1) Move the Slider S, T Ass’y 1, 2 to slot, and then lift it to remove.
(Refer to arrow)
Fig. 2-36 Slider S, T Ass’y Removal
2-4-24 Plate Ground Deck, Cylinder Ass’y Removal
1) Remove the 3 Screws 1.
2) Lift the Plate Ground Deck 2.
3) Lift the Cylinder Ass’y 3.
2) Lift the Plate Ground Deck 2.
3) Lift the Cylinder Ass’y 3.
Assembly:
1) Match the 3 holes in the bottom of Cylinder Ass’y 3 to the 3
holes of Main Base as attending not to drop or knock the Cylinder
Ass’y 3.
Ass’y 3.
2) Tighten the 1 Screw 1.
3) Match the Plate Ground Deck 2 to the Hole of Base Main.
4) Tighten the other 2 Screws 1.
3) Match the Plate Ground Deck 2 to the Hole of Base Main.
4) Tighten the other 2 Screws 1.
Note:
1) Take care not to touch the Cylinder Ass’y 3 and the tape guide
post at reinstalling.
2) When reinstalling, Don't push down too much on Screw Driver.
Fig. 2-37 Plate Ground Deck, Cylinder Ass’y Removal
Click on the first or last page to see other SLV-D920B / SLV-D920E / SLV-D920N / SLV-D920R / SLV-D925E / SLV-D930D / SLV-D930GI / SLV-D960PB / SLV-D960PE service manuals if exist.