Sony SLV-D900E / SLV-D900G Service Manual ▷ View online
— 5 —
2 Pick-up Disassembly and Reassembly
2-1 Disassembly
1) Remove the power cord.
2) Disassemble the Deck-Assy.
3) Make solder land 2 points short on Pick-up.
2) Disassemble the Deck-Assy.
3) Make solder land 2 points short on Pick-up.
(See Fig. 2)
4) Disassembly the Pick-up.
2-2 Assembly
1) Replace the Pick-up.
2) Remove the soldering 2 points on Pick-up.
3) Reassemble the Deck-Assy.
2) Remove the soldering 2 points on Pick-up.
3) Reassemble the Deck-Assy.
Note:
If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged.
SOLDER LAND 2 POINTS SHORT
PICK-UP ASS'Y
Fig. 2
1-1
1. GENERAL
SLV-D900E/D900G
This section is extracted from instruction manual. (3-079-775-11)
8
Unpacking
Getting Started
Step 1 : Unpacking
Check that you have received the following items with the DVD-VCR:
• Remote commander
• R6 (Size AA) batteries
• Aerial cable
• Audio cord
(pinplug ×2
y pinplug ×2)
• Video cord
(pinplug ×1
y pinplug ×1)
Getti
ng Sta
rted
9
Setting up the remote commander
Step 2 : Setting up the remote commander
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
• Do not use different types of batteries.
Inserting the batteries
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
commander
You can use this remote
commander to operate this DVD-
VCR and a Sony TV. Buttons on
the remote commander marked
with a dot (•) can be used to
operate your Sony TV.
commander to operate this DVD-
VCR and a Sony TV. Buttons on
the remote commander marked
with a dot (•) can be used to
operate your Sony TV.
If the TV does not have the
symbol near the remote sensor, this
remote commander will not
operate the TV.
remote commander will not
operate the TV.
To operate
Set TV / DVD·VIDEO to
the DVD player
DVD·VIDEO, then press SELECT DVD and point at the remote sensor at
the
the
DVD-VCR
the VCR
DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor
at the
at the
DVD-VCR
your TV
TV and point at the remote sensor at your TV
TV /
DVD·VIDEO
Remote sensor
continued
10
Setting up the remote commander
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer’s code number.
listed in the following table, set the appropriate manufacturer’s code number.
Now you can use the
?/1, VOL +/–, PROG +/–, MUTING*, TV/VIDEO, 0-9 and
-/--* buttons to control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to
DVD·VIDEO.
control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to
DVD·VIDEO.
* for Sony TV only
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
the one that works with your TV.
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the
DVD-VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
1
Set TV / DVD·VIDEO at the top of the remote commander to TV.
2
Hold down
?/1, and enter your TV’s code number using the number buttons.
Then release
?/1.
Manufacturer
Code number
Sony
01, 02
Akai
68
Ferguson
52
Grundig
10, 11
Hitachi
24
JVC
33
Loewe
45
Mivar
09, 70
NEC
66
Nokia
15, 16, 69
Panasonic
17, 49
Philips
06, 07, 08
Saba
12, 13
Samsung
22, 23
Sanyo
25
Sharp
29
Telefunken
36
Thomson
43
Toshiba
38
Manufacturer
Code number
Getti
ng Sta
rted
11
Connecting the DVD-VCR
Step 3 : Connecting the DVD-VCR
Note that “Advanced Hookups” (page 49) explains additional hookup methods that
will optimize the picture and sound for a true “hometheater” experience.
will optimize the picture and sound for a true “hometheater” experience.
If your TV has a Scart (EURO-AV) connector, see page 12.
If your TV does not have a Scart (EURO-AV) connector
Note
• When you connect the DVD-VCR and your TV only with an aerial cable, you have
• When you connect the DVD-VCR and your TV only with an aerial cable, you have
to tune your TV to the DVD-VCR (see page 14).
1
Disconnect the aerial cable from your TV
and connect it to
and connect it to
on the rear panel of the
DVD-VCR.
2
Connect
of the DVD-VCR and the
aerial input of your TV using the supplied
aerial cable.
aerial cable.
3
Connect the mains lead to the mains.
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
: Signal flow
continued
1-2
12
Connecting the DVD-VCR
If your TV has a Scart (EURO-AV) connector
1
Disconnect the aerial cable from your
TV and connect it to
TV and connect it to
on the rear
panel of the DVD-VCR.
2
Connect
of the DVD-VCR and the
aerial input of your TV using the
supplied aerial cable.
supplied aerial cable.
3
Connect LINE-1 (EURO AV) on the
DVD-VCR and the Scart (EURO-AV)
connector on the TV with the optional
Scart cable.
DVD-VCR and the Scart (EURO-AV)
connector on the TV with the optional
Scart cable.
This connection improves picture and
sound quality. Whenever you want to
watch the DVD-VCR picture, press
TV/VIDEO to display the VIDEO
indicator in the display window.
sound quality. Whenever you want to
watch the DVD-VCR picture, press
TV/VIDEO to display the VIDEO
indicator in the display window.
4
Connect the mains lead to the mains.
Mains lead
LINE-1
(EURO AV)
(EURO AV)
AERIAL IN
Scart
(EURO-AV)
(EURO-AV)
to mains
Aerial cable (supplied)
: Signal flow
Scart cable (not supplied)
Getti
ng Sta
rt
ed
13
Connecting the DVD-VCR
Additional connections
To a satellite or digital tuner
with Line Through
with Line Through
Using the Line Through
function, you can watch
programmes from a satellite or
digital tuner connected to this
DVD-VCR on the TV even
when the DVD-VCR is turned
off. When you turn on the
satellite or digital tuner, this
DVD-VCR automatically sends
the signal from the satellite or
digital tuner to the TV without
turning itself on.
function, you can watch
programmes from a satellite or
digital tuner connected to this
DVD-VCR on the TV even
when the DVD-VCR is turned
off. When you turn on the
satellite or digital tuner, this
DVD-VCR automatically sends
the signal from the satellite or
digital tuner to the TV without
turning itself on.
Notes
• This function may not work with some types of satellite or digital tuners.
• When the DVD-VCR is turned off, set the TV to the video channel.
• This function may not work with some types of satellite or digital tuners.
• When the DVD-VCR is turned off, set the TV to the video channel.
1
Connect the satellite or digital tuner to the LINE-3 connector as shown above.
2
Turn off the DVD-VCR.
To watch a programme, turn on the satellite or digital tuner and the TV.
Scart cable (not supplied)
LINE-3
LINE OUT
: Signal flow
14
Setting up the DVD-VCR with the Auto Set Up function
Step 4 : Setting up the DVD-VCR with the
Auto Set Up function
Before using the DVD-VCR for the first
time, set up the DVD-VCR using the Auto
Set Up function. With this function, you can
set TV channels, guide channels for the
VIDEO Plus+ system, and DVD-VCR clock
automatically.
time, set up the DVD-VCR using the Auto
Set Up function. With this function, you can
set TV channels, guide channels for the
VIDEO Plus+ system, and DVD-VCR clock
automatically.
1
Turn on your TV and set it to the video channel.
If your TV does not have a Scart (EURO-AV) connector, tune the TV to
channel 21 (the initial RF channel for this DVD-VCR). Refer to your TV
manual for TV tuning instructions. If the picture does not appear clearly,
see “To change the RF channel” on page 15.
channel 21 (the initial RF channel for this DVD-VCR). Refer to your TV
manual for TV tuning instructions. If the picture does not appear clearly,
see “To change the RF channel” on page 15.
2
Connect the mains lead to the mains.
The DVD-VCR automatically turns on and the
DVD-VCR starts searching for all of the
receivable channels and presets them (in the
appropriate order for your local area).
The DVD-VCR automatically turns on and the
DVD-VCR starts searching for all of the
receivable channels and presets them (in the
appropriate order for your local area).
If you want to change the order of the channels
or disable unwanted programme positions, see
“Changing/disabling programme positions” on page 21.
or disable unwanted programme positions, see
“Changing/disabling programme positions” on page 21.
After the search is complete, the current time appears for any stations that
transmit a time signal. If the time does not appear, set the clock manually.
See “Setting the clock” on page 17.
transmit a time signal. If the time does not appear, set the clock manually.
See “Setting the clock” on page 17.
V/v/B/b
ENTER
ENTER
O RETURN
ENTER
RETURN
A U T O S E T U P
P L E A S E W A I T
4 0 %
Getti
ng Sta
rted
15
Setting up the DVD-VCR with the Auto Set Up function
To cancel the Auto Set Up function
Press
O RETURN.
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on the DVD-
VCR and TV. Select
(INSTALLATION) from the menu, then press
V/v to
select VIDEO OUTPUT CH. Select the RF channel by pressing the
B/b buttons.
Then, tune the TV to the new RF channel so that a clear picture appears.
Tip
• If you want to change the language for the on-screen display from the one preset in the Auto
• If you want to change the language for the on-screen display from the one preset in the Auto
Set Up function, see page 16.
Notes
• Whenever you operate the Auto Set Up function, some of the settings (VIDEO Plus+, timer,
• Whenever you operate the Auto Set Up function, some of the settings (VIDEO Plus+, timer,
etc.) will be reset. If this happens, you have to set them again.
• Auto preset starts automatically only when you plug in the mains lead for the first time after
you purchase the DVD-VCR.
• If you want to use the Auto Set Up function again, press SET UP, then press
V/v/B/b to
select
(INSTALLATION) and press ENTER. Press
V/v to select AUTO SET UP.
• Auto preset can be performed by pressing
x on the DVD-VCR continuously for 5 seconds or
more during power off with no tape inserted.
1-3
16
Selecting a language
Step 5 : Selecting a language
You can change the on-screen display
language.
language.
Before you start…
• Turn on the DVD-VCR and your TV.
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
TV screen.
• If the DVD player is in play mode, you
cannot display the “SETUP MENU.” Stop
DVD playback.
DVD playback.
1
Press SET UP.
The “SETUP MENU” appears.
2
Press
V/v/B/b to select
(LANGUAGE
SET), then press ENTER.
The “LANGUAGE SET” menu appears.
3
Press
V/v to select the desired language, then press ENTER.
4
Press
O RETURN to exit the menu.
V/v/B/b
ENTER
ENTER
SET UP
O RETURN
SET UP
DVD SETUP
RETURN
RETURN
SETUP MENU
Vv b
B
ENTER
ENTER
English
Français
Deutsch
Français
Deutsch
RETURN
LANGUAGE SET
v
V
ENTER
B
Español
Italiano
Nederlands
Italiano
Nederlands
ENTER
RETURN
Getti
ng Sta
rt
ed
17
Setting the clock
Step 6 : Setting the clock
You must set the time and date on the DVD-
VCR to use the timer features properly.
VCR to use the timer features properly.
The Auto Clock Set function works only if a
station in your area is broadcasting a time
signal.
station in your area is broadcasting a time
signal.
Before you start…
• Turn on the DVD-VCR and your TV.
• Set your TV to the video channel so that
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
TV screen.
• If the DVD player is in play mode, you
cannot display the “SETUP MENU.” Stop
DVD playback.
DVD playback.
1
Press SET UP.
The “SETUP MENU” appears.
2
Press
V/v/B/b to select
(CLOCK SET),
then press ENTER.
The “CLOCK SET” menu appears.
3
Press
V/v to set the hour.
V/v/B/b
ENTER
ENTER
SET UP
O RETURN
SET UP
DVD SETUP
RETURN
RETURN
SETUP MENU
Vv b
B
ENTER
ENTER
RETURN
INSTALLATION
1 2 : 0 0
1 / JAN / 2002
AUTO CLOCK : ON
CLOCK SET
TUE
vV
B
b
ENTER
RETURN
1 8 : 0 0
1 / JAN / 2002
AUTO CLOCK : ON
CLOCK SET
TUE
vV
B
b
continued
18
Setting the clock
Tips
• If you set “AUTO CLOCK” to “ON”, the Auto Clock Set function is activated whenever the
• If you set “AUTO CLOCK” to “ON”, the Auto Clock Set function is activated whenever the
DVD-VCR is turned off. The time is adjusted automatically by making reference to the time
signal from the station.
signal from the station.
• To change the digits while setting, press
B to return to the item to be changed, and select the
digits by pressing
V/v.
4
Press
b to select the minutes and set the
minutes by pressing
V/v.
5
Set the day, month, and year in sequence by
pressing
pressing
b to select the item to be set, and
press
V/v to select the digits, then press b.
The day of the week is set automatically.
6
Press
V/v to select
“
ON
”
for the setting of the
Auto Clock Set function.
The DVD-VCR automatically sets the clock
according to the time signal broadcast between
the channels PR 1 to PR 5.
according to the time signal broadcast between
the channels PR 1 to PR 5.
If you do not need the Auto Clock Set function,
select OFF.
select OFF.
7
Press
O RETURN repeatedly to exit the menu.
ENTER
RETURN
1 8 : 3 0
1 / JAN / 2002
AUTO CLOCK : ON
CLOCK SET
TUE
vV
B
b
ENTER
RETURN
1 8 : 3 0
28 / SEP / 2002
AUTO CLOCK : ON
CLOCK SET
SAT
vV
B
b
ENTER
RETURN
1 8 : 3 0
28 / SEP / 2002
AUTO CLOCK : ON
CLOCK SET
SAT
vV
B
b
RETURN
Getti
ng Sta
rted
19
Presetting channels
Step 7 : Presetting channels
If some channels could not be preset using
the Auto Set Up function, you can preset
them manually.
the Auto Set Up function, you can preset
them manually.
Before you start…
• Turn on the DVD-VCR and your TV.
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
TV screen.
• If the DVD player is in play mode, you
cannot display the “SETUP MENU.” Stop
DVD playback.
DVD playback.
1
Press SET UP.
The “SETUP MENU” appears.
2
Press
V/v/B/b to select
(INSTALLATION), then press ENTER.
The “INSTALLATION” menu appears.
V/v/B/b
ENTER
ENTER
SET UP
O RETURN
SET UP
DVD SETUP
RETURN
RETURN
SETUP MENU
Vv b
B
ENTER
ENTER
RETURN
INSTALLATION
MANUAL SET UP
AUTO SET UP
VIDEO OUTPUT CH : CH21
INSTALLATION
ENTER
vV
continued
Click on the first or last page to see other SLV-D900E / SLV-D900G service manuals if exist.