DOWNLOAD Sony GV-D300 Service Manual ↓ Size: 27.72 MB | Pages: 127 in PDF or view online for FREE

5-41

Page D

Address 10

• Before setting the data , select page: 0, address: 01, and set data:

01.

• For page D, the data set is recorded in the non-volatile memory

by pressing the PAUSE button of the adjustment remote
commander. In this case, take note that the test mode will not be
exited even when the main power is turned off (8.4Vdc).

• After completing adjustments/repairs, be sure to return the data

of this address to 00, and press the PAUSE button of the adjustment
remote commander.
Select page: 0, address: 01, and set data: 00.

Page C

Address 30 to 3B

When no error occurs in this unit, data “00” is written in the above
addresses (30 to 3B). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency address
(30 to 33). In the same way, when the second error occurs, the data
corresponding to the error is written in the second emergency address
(34 to 37). Finally, when the last error occurs, the data corresponding
to the error is written in the last emergency address (38 to 3B).

After completing adjustments, be sure to initialize the data of
addresses 30 to 3B to “00”.

Initializing method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 3, address: 01, set data: FD, and press the PAUSE
button.

3)

Select page: 0, address: 01, and set data: 00.

Normal

Forced VTR power ON

00

02

EMG code when first error occurs

Upper: MSW code when shift starts when first
error occurs
Lower: MSW code when first error occurs

Lower: MSW code to be moved when first error
occurs

EMG code when second error occurs

Upper: MSW code when shift starts when second
error occurs
Lower: MSW code when second error occurs

Lower: MSW code to be moved when second error
occurs

EMG code when last error occurs

Upper: MSW code when shift starts when last error
occurs
Lower: MSW code when last error occurs

Lower: MSW code to be moved when last error
occurs

30

32

33

34

36

37

38

3A

3B

Codes corresponding to the errors which occur are written in
addresses 30, 34 and 38. The type of error indicated by the code are
shown in the following table.

No error

Loading motor emergency during loading

Loading motor emergency during unloading

T reel emergency during normal rotation

S reel emergency during normal rotation

T reel emergency (Short circuit between S reel
terminal and T reel terminal)

FG emergency at the start up of the capstan

FG emergency at the start up of the drum

FG emergency during normal rotation of the drum

00

10

11

22

23

24

30

40

42

5-42

MSW when errors occur:
Information on MSW (mode SW) when errors occur
MSW when movement starts:
Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved)
MSW of target of movement:
Information on target MSW of movement when the mechanism position is moved

1010=A

1111=F

←

 UNLOAD

Lock released

Cassette compartment

LS chassis movement section

Pinch roller pressing
Tension regulator ON

EJECT

BL

1110=E

1111=F

USE

BL

1100=C

1111=F

SOFF

BL

1101=D

1111=F

DS

BL

1001=9

1111=F

LE

BL

0101=5

1111=F

STOP

BL

0111=7

1111=F

FF

BL

BL

1011=B

1111=F

0011=3

RP

RVS

LOAD 

→

EJECT

BL

USE

SOFF

DS

LE

STOP

FF

RP

RVS

NULL

A

F

E

C

D

9

5

7

B

3

0

Position at which the cassette component lock is released, and position at the farthest unload side
mechanically at which the mechanism can move no further in the UNLOAD direction.

BLANK code, at the boundary between codes. The mechanism will not stop at this code during
operations. (Excluding LOAD/UNLOAD)

EJECT completion position. When the cassette is ejected, the mechanism will stop at this position.
Cassette IN standby. The guide will start protruding out as the mechanism moves towards the
LOAD position.

Code during loading. Code output while the LS chassis is moving.

LS operations and guide loading are performed here.

Current limiter is turned off.

Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the
brake is imposed on both reels.

FF position. The tension regurator is half on. This position is not used except for the FF mode.

PB, REC, CUE, PAUSE, FX2, FWD-SL positions. When the pinch roller is pressed, and the
tension regulator is ON, the mechanism is operating at this position in modes in which normal
images are shown.

Reverse running position. REW, REV, RX1, RX2, and RVS-SLOW are performed at this position.

Code not exsisting in the MD. When errors occur when the loading motor is not driving, this code
is memorized.

5-43

Bit values must be discriminated using the display data of the
adjustment remote commander for following items. Use the table
below to discriminate if the bit value is “1” or “0”.

Page

Address

bit3 to bit0 discrimination

bit7 to bit4 discrimination

Display on the adjustment remote commander

0

1

2

3

4

5

6

7

8

9

A (

A

)

B (

b

)

C (

c

)

D (

d

)

E (

E

)

F (

F

)

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

0

0

0

0

1

1

1

1

0

0

0

0

1

1

1

1

0

0

1

1

0

0

1

1

0

0

1

1

0

0

1

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

A

B

If “8E” is displayed on the adjustment remote commander, the
bit values for bit7 to bit4 are shown in the 

A column, and the

bit values for bit3 to bit0 are shown in the 

B column.

Page 2

Address 43

Using method:
1)

Select page: 2, address: 43.

2)

By discriminating the bit value of display data, the state of the
switches can be discriminated.

0

1

2

3

4

5

6

7

VTR MODE SW

EJECT SW

CC DOWN SW

OFF

OFF

OFF

ON

ON

ON

5-44E

Page 2

Address 5C to 62

Using method:
1)

Select page:2, address: 5C to 62.

2)

By discriminating the display data, the pressed key can be discriminated.

Page 2

Address 35 to 3D

Using method:
1)

The record of use data is displayed at page: 2, addresses: 35 to 3D.

This data will be erased when the coin lithium battery (FP-571 board BT001) is removed (reset).

5C

(AD0)

(IC2302 

*ª)

5D

(AD1)

(IC2302 

(º)

5E

(AD2)

(IC2302 

(¡)

5F

(AD3)

(IC2302 

(™)

61

(AD5)

(IC2302 

(¢)

62

(AD6)

(IC2302 

(∞)

STOP

(FK-71 board S001)

PAUSE

(FK-71 board S007)

DISPLAY

(FK-71 board S009)

MENU

(IO-62 board  S102)

PANEL CLOSE

(IR-29 board S361)

LASER LINK

(IO-62 board S101)

PLAY

(FK-71 board S002)

SLOW

(FK-71 board S008)

TITLE

(FK-71 board S010)

EXECUTE

(IO-62 board S107)

LCD BRIGHT +

(IO-62 board S103)

REC

FK-71 board

 S003,004

LCD BRIGHT –

(IO-62 board S104)

FF

(FK-71 board S005)

AUDIO DUB

(FK-71 board S012)

VOLUME +

(IO-62 board S105)

REW

(FK-71 board S006)

ASSEMBLE

(FK-71 board S013)

VOLUME –

(IO-62 board S106)

No key input

No key input

No key input

No key input

PANEL OPEN

(IR-29 board S104)

No key input

35

36

37

38

39

3A

3B

3C

3D

Drum rotation

counted time

(BCD code)

User initial power

on date

(BCD code)

Final condensation

occurrence data

(BCD code)

Minute

Hour (L)

Hour (H)

Year

Month

Day

Year

Month

Day

10th place digit and 1st place digit of counted time (decimal digit)

1000th place digit and 100th place digit of counted time (decimal digit)

After setting the clock, set the date of power on next

                     

                     