DOWNLOAD Sony KV-XA29M60 Service Manual ↓ Size: 6.08 MB | Pages: 119 in PDF or view online for FREE

–

 25 

–

Using Your New TV

4

If you wish to connect a VCR, see the Connecting a VCR diagram below.

To watch the video input, press t (see page 11).

To t 1, 2 or 3
(video input)

To 8
(antenna)

VIDEO

VIDEO IN

VIDEO OUT

AUDIO

R       L

1

2

3

R

L

Y

C

B

C

R

CAUTION
• Do not connect the power cord until you have completed making all other

connections; otherwise a minimum leakage current might flow through
the antenna and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries

from the remote if you are not going to use it for several days. If any
liquid that leaks from the batteries touches you, immediately wash it
away with water.

5

Using Your New TV

Notes
• If you connect a monaural VCR, connect the yellow plug to 

 (the yellow

jack) and the black plug to  -L (MONO) (the white jack).

• If you connect a VCR to the  (antenna) terminal, preset the signal output

from the VCR to the program number 0 on the TV.

• If both 

 (S video input) and t 1 (video input) at the rear of your TV

are input at the same time, the 

 (S video input) is automatically

selected. To view the video input to t 1 (video input), disconnect the
S video cable.

• Do not connect video equipment to the t 3 (video input) jacks at the

front and the rear of your TV at the same time; otherwise the picture will
not be displayed properly on the screen.

• When no signal is input from the connected video equipment, the TV

screen becomes blue.

Note
• Do not use old batteries nor use different types of batteries together.

Tips
• If you want to stop the automatic channel presetting, press MENU.
• If your TV has preset an unwanted channel or cannot preset a particular

channel, then preset your TV manually (see page 27).

PROGR

MENU

AUTO
PROGR

ENTER

SELECT

L(MONO)

3

–

 26 

–

Using Your New TV

6

WOOFER

(8

Ω)

Attach the 3D WOOFER into the footholds on the top of your TV.

Connect the wires to the 3D WOOFER (8

Ω) terminals at the rear of your TV.

The red wire should be connected to the 3 red terminal and the black wire
to the # black terminal.

Notes
• Connect only the supplied 3D WOOFER; otherwise your TV may

malfunction.

• Unplug your TV from the wall outlet when connecting the 3D WOOFER.
• To prevent a malfunction caused by a short circuit of the terminals, make

sure that none of the 3D WOOFER wire strands stick out, making contact
with the neighbouring speaker terminal.

You can enjoy high quality sound by connecting the 3D WOOFER.

7

Using Your New TV

Connecting audio/video equipment using the T
(monitor output) jacks

You can connect optional audio/video components, such as a VCR, multi disc player,
DVD, camcorder, video game or stereo system.

To watch the video input of the connected equipment, press t (see page 11).

Connecting a camcorder/video game equipment
using the t (video input) jacks

Notes
• You can also connect video equipment to the t 1 or 2 (video input) jacks

at the rear of your TV.

• If both 

 (S video input) and t 3 (video input) at the front of your TV

are input at the same time, the 

 (S video input) is automatically

selected. To view the video input to t 3 (video input), disconnect the
S video cable.

• Do not connect video equipment to the t 3 (video input) jacks at the

front and the rear of your TV at the same time; otherwise the picture will
not be displayed properly on the screen.

PROGR

MENU

AUTO
PROGR

ENTER

SELECT

L(MONO)

3

L (MONO)

R

3

t

To T
(monitor
output)

1

2

3

R

L

Y

C

B

C

R

Note
• If you select “DVD” on your TV screen, no signal will be output at the T

(monitor output) jacks (see page 11).

(Not used for this model)

–

 27 

–

Using Your New TV

8

Connecting a DVD player using the t (video input) jacks

VIDEO 

R-AUDIO-L

LINE  OUT

 (yellow)

To t 1, 2, or 3
(video input)

• Some DVD player terminals may be labeled differently:

Y (green)

Y

C

B

 (blue)

C

b

, B-Y or P

B

C

R

 (red)

C

r

, R-Y or P

R

1 Connect R and L under 

 (component video input) on your TV to the LINE OUT,

AUDIO R and L output connectors on your DVD player.

2 Using a component video cable, connect Y, C

B

, and C

R

 under 

 (component video

input) on your TV to the COMPONENT VIDEO OUT Y, C

B

, and C

R

 output

connectors on your DVD player.

• Since the high quality pictures on a DVD disc contain a lot of information,

picture noise may appear. In this case, adjust the sharpness (“SHARP”) in
the “ADJUST” menu of the “PICTURE MODE” menu (see page 21).

• Connect your DVD player directly to your TV. Connecting the DVD player

through other video equipment will cause unwanted picture noise.

VIDEO 

R-AUDIO-L

LINE  OUT

Y 

COMPONENT VIDEO OUT

S VIDEO OUT

C

B

 

C

R

 

9

Using Your New TV

To prevent the TV from falling, secure the TV using one of the following methods:

A

With the supplied screws, attach the band to the TV stand and to the rear of
the TV using the provided hole.

B

Put the cord or chain through the clamps to secure the TV against a wall or
pillar.

Note
• Use only the supplied screws. Use of other screws may damage the TV.

A

B

–

 28 

–

Using Your New TV

10

This section explains various functions
and operations available while watching
the TV. Most operations can be done
using the remote.

Press ! to turn on the TV.

When the TV is in the
standby mode (the 1
indicator on the TV is lit
red), press ?/1 on the
remote or PROGR +/– on
the TV.

Press PROGR +/– or
number buttons to select
the program number.

For double digit numbers,
press -, then the number
(e.g., for 25, press -,  then
2 and 5).

%

?/1

t 

a

2

PROGR

MENU

AUTO
PROGR

ENTER

SELECT

L(MONO)

3

PROGR

MENU

AUTO

PROGR

ENTER

SELECT

 1

(1) Press and hold PROGR +/–.
(2) Release PROGR +/– when the desired program number appears.

Note
• When you select a program number quickly, the picture may be disrupted.

This does not indicate a malfunction.

11

Using Your New TV

Turn off temporarily

Turn off completely

Adjust the volume

Mute the sound

Watch the video input

(VCR, camcorder, etc.)

Jump back to the previous program

number

Display the on-screen information*

?/1

. The 1 indicator on the TV lights up red.

!

 on the TV.

2

 +/–.

%

.

t to select “VIDEO 1”, “VIDEO 2” , “VIDEO 3”

or “DVD”.

To return to the TV program, press a (or t on the TV).

JUMP.

.

* The picture, sound, and either the program number or video input are

displayed. The on-screen display for the picture and sound information
disappears after about three seconds.

You can change the menu language as well as the on-screen language.

For details on how to use the menu, see Introducing the menu system on page 18.

Press MENU.

Press + or – to select the
“SETUP” icon (

), then

press ENTER.

Make sure “LANGUAGE” is
selected, then press ENTER.

Press + or – to select the
desired language (e.g,
“

”), then press ENTER.

The selected menu language appears.

Press MENU.

P I C T URE +

+MO

C

P I C T URE

I N T E L L I GEN T P I C : OF F

WI DE MODE : OF F

DE : DYNAM I

L ANGUAGE :

CO L OR S Y S :

S E T UP

PROGRAM S E

P I C ROT A T I

ENG L I SH

E

CO L OR S Y S : AU TO

S E T UP

PROGRAM S E T UP

P I C ROT A T I ON

NG L I SH

L ANGUAGE :