DOWNLOAD Sony KV-XA29M31 Service Manual ↓ Size: 4.75 MB | Pages: 110 in PDF or view online for FREE

– 29 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will be
reset to its original setting (shipment condition)

The way to access to the "RESET" Function:-

a) By pressing "MENU" button or "SELECT" button (for non-menu models) on the Front Key Input and

hold it down for 5 seconds.

Sequential to the resetting operation (either methods being used in No. 2), TV set would shut down once and
automatically turn on again. The power-off duration is expected to be about 500msec. An OSD message,
"RESET" tentatively will be displayed for 10 sec after IK status gets stable.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other remains at
the last selection by user.

Items that remains at the last selection by user

Reset Items

Program No., Favourite CH Setup, PIC rotation,

OSD Language, Fine tuning, TV System, Skip

*= only when in RF mode

Video input

RF

Volume

30

Picture mode

DYNAMIC

Sound mode

DYNAMIC

Surround mode

OF

Color system(video)

AUTO

Favourite CH mode

AUTO

Multi Picture (PIP)

OFF

PIP position

Bottom Right

OSD recall

OFF

Intelligent volume

OFF

ECO mode

OFF

Color system(RF)

AUTO*

Antenna sensitivity

HIGH*

Stereo mode

STEREO/NICAM*
(except KV-XA29M50)

Bilingual mode

MAIN*
(except KV-XA29M50

High-deviation mode

AUTO*

Child lock

OFF*

Wide mode

OFF

Game mode

OFF

Teletext mode

OFF (except
KV-XA29M50)

Sleep timer

OFF

Wake-up timer

OFF

Sound muting

OFF

}

Not used for
this model

– 30 –

•

The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

•

These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise noted:

PICTURE control ...........................................................  normal

BRIGHTNESS control ...................................................  normal

Perform the adjustments in the following order :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note :  Test Equipment Required.

1. Pattern Generator

2. Degausser

3. Oscilloscope

................................................................................................................................................................................................................................

normal

•

In order to reduce the influence of geomagnetism on the set's

picture tube, face it east or west.

•

Switch on the set's power and degauss with the degausser.

1. Input a white signal with the pattern generator.

Contrast
Brightness

2. Position neck assy as shown in Fig4-2.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 4-1 through 4-4.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 4-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been decided,

fasten the deflection yoke with the screws and DY spacers.

8. If the beam does not land correctly in all the corners, use a

magnet to adjust it.

(See Figure 4-5.)

}

Neck assy

G2

G1

G3

Behind the G2 edge

Purity control

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

– 31 –

•

Before starting this adjustment, adjust the focus, horizontal size
and vertical size.

•

Receive dot/hatch signal.

•

Pic mode: Personal (Pic 90%, Brightness 50%, Col 50 %,

Hue 50%, Shp 50%).

1. (Moving horizontally), adjust the H.STAT control so that the

red, green and blue dots are on top of each other at the center of
the screen.

2. (Moving vertically), adjust the V.STAT magnet so that the red,

green and blue dots are on top of each other at the center of the
screen.

3. If the H.STAT variable resistor cannot bring the red, green and

blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform adjustments
while tracking.)

1

V. STAT

2

H. STAT VR

3

Center dot

R    G    B

R

G

B

H. STAT VR

V. STAT

Magnet

RV702

H. STAT

RV701
SCREEN (G2)

C6 Board

BMC (Hexapole)

V.STAT

DY pocket

Purity

V.STAT

BMC

Purity

R

R

R

R

G

G

G

G

B

B

B

B

a

a

a

b

b

b

b

R

R

G

G

B

B

a

a

b

b

b

– 32 –

5

Y separation axis correction magnet adjustment.

1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN]

and [BRIGHTNESS] to [STANDARD]  .

2. Adjust the Y separation axis correction magnet on the neck

assembly so that the horizontal lines at the top and bottom of
the screen are straight.

Note
1. The Red and Blue magnets should be equally far from the

horizontal center line.

2. Do not separate the Red and Blue magnets too far. (Less than

8 mm)

•

Before starting this adjustment, adjust the horizontal static

convergence and the vertical static convergence

4

BMC (Hexapole) Magnet.
If the red, green and blue dots are not balanced or aligned, then
use the BMC magnet to adjust in the manner described below.

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

Blue

Red

VM1 board

Blue

Red

VM1 board

Neck assy

Neck assy

R B

R B

TLH

TLV

YCH

XCV

B

R

R

B