DOWNLOAD Sony KV-SZ252M50 (serv.man2) Service Manual ↓ Size: 8.72 MB | Pages: 72 in PDF or view online for FREE

– 9 –

ii) Insert the 2 Earth Assy, Coating wires to CN705 &  
CN707 as shown. Insert Conn Assy, 7P RGB into CN701.

CV board

Heatsink A751

Conn Assy, 7P RGB

CN707

Earth Assy, Coating dressing

CV board

CN707

CN705

CN705

Earth Assy,

Coating wires

CN701

BLK+BLK

to CN705

BLK+BLK

to CN707

Make a 'S' shaped loop on Conn Assy, 5P Front In  
as shown. Keep wires away from heatsink A010.

Next, Conn Assy, 5P Front In is dressed together with  
Lead Assy,Earth using purse lock Ø 5. Refer to next page.

Lead Assy, Earth

Lead Assy, Speaker

Heatsink A010

Conn Assy, 5P

Front In

Insert Lead Assy, H Static into CRT socket and RV750 as 
shown. Make sure the wire is naturally curved, to avoid 
touching CRT neck.

Lead Assy, H static

CRT socket

CRT neck

RV750

– 10 –

Note: Dress while chassis is halfway docked into beznet.

CAUTION:
Prevent tie, cable from touching rear cover or any 
enclosures by turning them away from it --> avoid 
rattle sound. Also prevent tie, cable's end from  
touching solder side of board.

CAUTION:
Prevent tie, cable from touching rear cover or any 
enclosures by turning them away from it --> avoid 
rattle sound. Also prevent tie, cable's end from  
touching solder side of board.

i) Dress Conn Assy, 6P and Conn Assy, 4P VM using tie,
cable at alignment hole 'B' on CV board as shown.
ii) Dress Conn Assy, 4P 200V; Conn Assy, 6P; Conn Assy,
4P VM; Lead Assy, G2 and Lead Assy, Focus with purse
lock Ø 5.

  

Lead Assy, Earth

Conn Assy, 5P Front In

Heatsink A010

Tie, cable at alignment hole 'B'

Conn Assy, 6P

Conn Assy, 4P VM

Conn Assy, 4P VM

Conn Assy, 4P 200V

Conn Assy, 6P

Lead Assy, Focus

Lead Assy, G2

Conn Assy, 4P 200V

Lead Assy, G2

Lead Assy, Focus

Pin, wire A707

Purse lock Ø 5

Purse lock Ø 5

Purse lock Ø 5

Lead Assy, Speaker is not dressed 

together with purse lock. Keep Lead Assy,  

Speaker away from heatsink A010 by

dressing it close to the CRT

Make a 'S' shaped loop on 

Conn Assy, 5P Front In 

and dress together with  

Lead Assy, Earth using 

purse lock Ø 5

Conn Assy,  
5P Front In

Lead Assy, Earth

i) Dress Conn Assy, 7P RGB; Conn Assy, 5P Front In and
Lead Assy, Earth using purse lock Ø 9. Keep wires away from 
heatsinks and high-temperature parts. 

Lead Assy, Earth is behind

Conn Assy, 7P RGB

Purse lock Ø 9

Conn Assy, 7P RGB

Conn Assy, 5P Front In

CN004

Make loop of Conn Assy, 7P RGB as large as 

possible when dressing with purse lock

Lead Assy, Earth

Purse lock Ø 9

Conn Assy, 7P RGB

Lead Assy, Earth

Conn Assy, 5P Front In

Keep Conn Assy, 5P Front In wire in an upward
path from CN9201 to where it is dressed with 
purse lock Ø 9. This is to keep it away from 
deflection area.

– 11 –

Avoid any stress on Lead Assy, G2; Lead Assy, Focus and
terminal at W7001.

CN1802

Rotation Coil Conn

Dress Rotation Coil

connector together with Lead

Assy, G2; Lead Assy Focus

and Conn Assy, 4P 200V

using pin, wire A707

A715

A713

Conn Assy, 4P 200V

W7001

Lead Assy, G2

Lead Assy,

Focus

Keep wire away

from R781

Keep wire away

from R781 and 

heatsinks A713, A715.

Install Rotation Coil as shown.
1) Coil positioned in clockwise direction.
2) Wire is at 3 o'clock position.

Dress DY Connector; Conn Assy, 4P 200V;
Conn Assy 4P VM and Conn Assy, 6P using purse lock
Ø 9 as shown.

CAUTION:
Prevent wires from touching rear cover or any 
enclosures by turning them away from it--> avoid rattle
sound.

Rotation Coil

DY

Wire from Roation Coil

Earth Assy,

Coating wires

Rotation coil conn is dressed outside

and below Earth Assy, Coating wires.

Note: Make sure DY connector is inserted securely.
 

--> prevent it from coming out.

DY Connector

Conn Assy,

4P 200V

Conn Assy, 6P

  

Conn Assy,  

4P VM

Purse lock Ø 9

DY Conn

Conn Assy,

4P 200V

Conn Assy, 4P

Conn Assy, 6P

Purse lock Ø 9

– 12 –

Dress Lead Assy, Speaker to center position of Rotation Coil using purse lock Ø 9 as shown. Make sure Earth 
Assy, Coating wire is above Lead Assy, Speaker. This is to keep Lead Assy, Speaker away from Deflection Yoke.

TVSR Requirement: 
1. Keep HV cable away from conductive parts
 (distance of 1mm/kV).
2. Keep spacing between edge of anode cap 
& conductive parts (distance of 0.5mm/kV).
3. Keep spacing between edge of anode cap & 
non-conductive parts (distance of at least 5mm or more).

Earth Assy, Coating

wire

Dress Lead Assy, Speaker to

center position of Rotation Coil

using purse lock Ø 9

DGC Connector is below Conn Assy,

3P VH to keep Conn Assy, 3P VH

away from Heatsink A007 and D604

Keep wires away from 

heatsinks A007, D604 and 

conductive parts

Apply to all SZ252 Narrow 220V CISPR models ONLY

Clamp the ferrite core at the end of the DGC

wire as shown. Position it directly above DGC 

Connector's housing

Purse lock Ø 9

Rotation Coil

Lead Assy, Speaker
(RED+BLK)

Earth Assy, Coating wire is
above Lead Assy, Speaker

Rotation coil

DGC Connector

A007

D604

DGC Band

HV Cap

Rotation coil

DGC

CN605

CN6620

Housing

Connector Assy,

3P VH

DY

Rotation Coil

Attach purse lock Ø 9

here

Lead Assy,

Speaker

Lead Assy,

Speaker

Lead Assy, Speaker

goes behind DGC

Dress Lead Assy, Speaker

directly on to DGC using

purse lock Ø 9

Pull wire to left

Lead Assy, Speaker

goes behind DGC

Pull wire to 

the right

Loop Lead Assy, Speaker and  

dress directly on to DGC using  

purse lock 

Ø 9