DOWNLOAD Sony KV-SZ252M50 (serv.man2) Service Manual ↓ Size: 8.72 MB | Pages: 72 in PDF or view online for FREE

– 4 –

[+B overcurrent $OCP%]

Occurs when an overcurrent on the +B(135V) line is detected by pin 32 of IC001 (A board).
If the voltage of pin 32 of IC001 (A board) is more than 4V, the unit will automatically go to
standby.

[V-PROTECT]

Occurs when an absence of the vertical deflection pulse is detected by pin 13 of IC001
(A board).

[IK $AKB%]

If the RGB levels* do not balance within 15 sec after the power is turned on, this error will be
detected by IC001 (A board). TV will stay on, but there will be 5 times LED blinking.

Occurs when IC001 internal HV protect detects an abnormal H-Pulse (frequency) due to
improper power supply to IC001. TV cuts off high voltage power of anode CRT. No picture will be
detected. eg: IC602, IC604 go faulty.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

A BOARD

IC001

Y/CHROMA JUNGLE

A BOARD

IC503

V.OUT

A BOARD

IC001

SYSTEM

A BOARD

IC003

MEMORY

FROM

CV BOARD

IC751 PIN 5

IK

EHT0

RED LED

DISPLAY

SDA1

V.GUARD

SDA

5

F.B-PLS

3

13

84

32

122

A BOARD

FROM

Q816

COLLECTOR

99

POWER SUPPLY NG (+5V)
for VIDEO PROCESSOR

2 : 

000

3 :

N/A

4 :

000

5 :

001

8 :

002

101 :

N/A

"0" means no fault has been detected.

"1" means a fault has been detected.
"2" means two faults has been detected.

"N/A" means not available for this models.

SELF DIAGNOSTIC

5

8

1.

Display self diagnostic screen

[Display] t [Channel    ] t [Volume    ] t [Power / TV]

Note: The above must be performed while TV is on standby mode.

2.

Stop standby flash

i) Turn off power switch on main.
ii) Unplug power cord from the outlet.

3.

Clear fault result

In self diagnostic screen, press 

[Channel    ] t 

-

Note: Diagnostic results display on screen is not automatically cleared. Therefore,
clear result after completion of repair.

4.

Quit self diagnostic screen

Turn off power switch of remote commander or main unit.

– 5 –

1 Nine screws
     (+BVTP 4 × 16)   

2 Rear cover

1 Two screws
     (Tapping screw) 
     (+PWH 4x16)

2 H2 Board

3 A Board

1 Two hooks

– 6 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT

shield or carbon paint on the CRT.

•

1 Turn up one side of the rubber cap in the direction

indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direc-

tion indicated by the arrow b.

3 When one side of the rubber cap is separated from the

anode button,  the anode-cap can be removed by
turning up the rubber cap and pulling it up in the
direction of the arrow c.

•

1 Do not damage the surface of anode-caps with

2 Do not press the rubber too hard so as not to

3 Do not turn the foot of rubber over too hard.

•

Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom
right and left.

1) Remove the rear cover.
2) Unplug all interconnecting leads from the Deflection yoke, Neck assy, Degaussing Coil and CRT grounding strap.

Remove Chassis Assy.

3) Place the TV set with the CRT face down on a cushion jig.

a

a

c

 Anode Button

b

b

4

 Anode Cap Removal

9

 Degaussing Coil

6

 Loosen the Neck Assembly 

fixing screw and remove
Neck Assy

qa

 Loosen the Deflection Yoke

fixing screw and remove

5

 CV Board Removal

8

 Spring Tension(x2) 

Removal

qs

 Supports CRT (x2) 

 Removal

0

 Earth Coating Assy

qd

 Screw Tapping 

     7+ Crown Washer (x4)

7

 Band, DGC Removal

– 7 –

TVSR:
Connector assy must be kept away
from primary area(10mm minimum).

i) Insert and dress Conn Assy, 4P into hook.

ii) Insert Conn Assy, 5P into CN4105.
  Make sure AC Power Cord is behind Lead Assy,  
  Speaker at CN4106.

W082

W077

P/N 1-923-512-11

W016

Dress both Lead Assy, Jumpers

along edge of shield case

P/N 1-910-026-28

Conn Assy,

5P YUV

CN905

Dress both Lead  

Assy, Jumpers

around CN905, C903

and below Conn

Assy, 5P YUV

C903

Dress Lead Assy, Jumper far

away from C514 and T501

W010

W065

W084

C514

T501

Keep Lead Assy, Jumpers

away from R121

 No. Part 

No. 

Description 

Block 

Remark

 

1 1-910-026-28 

Lead 

Assy, 

Jumper 

A(Var)

 

W016-W084(1)

   

 

 

 

W077-W065(0)

  2 

1-923-512-11  WIRE UL1007 AWG24 150MM ORG 

A(Com)  W082-W010(1)

 No. Part 

No. 

Description 

Block 

Remark

  2 1-910-036-25 

Lead 

Assy, 

Jumper 

A(Var) W075-W085(1)

 

2

1

CN4113

CN3102

CN2105

CN4110

Conn Assy, 4P

CN4106

CN4105

Lead Assy, Speaker

Conn Assy, 5P

AC Power Cord is behind

Lear Assy, Speaker

Conn Assy, 7P

Insert Conn Assy,

4P into hook

W075

P/N 1-910-036-25

L2601

A003

A002

W085

Dress Lead Assy,

Jumper around C249

Dress Lead Assy, Jumper in

between C211 and L2601

C211

UL Tube

Dress between

A003 and A002

CAUTION :
1.  Do not overpull the wires during dressing

--> avoid disconnection of wires.

2.  Make sure wires are kept away from

sharp edges, heatsinks & other
high-temperature parts.