DOWNLOAD Sony KV-SR25M53K Service Manual ↓ Size: 7.79 MB | Pages: 81 in PDF or view online for FREE

– 11 –

Preparation:
Before starting this adjustment, adjust the horizontal  and
the vertical static convergence

7. Y separation axis correction magnet adjustment.

1. Receive the cross-hatch signal and adjust

[PICTURE] to [MIN] and [BRIGHTNESS] to
[STANDARD]  .

2. Adjust the Y separation axis correction magnet on

the neck assembly so that the horizontal lines at

the top and bottom of the screen are straight.

Neck assy

Neck assy

Red

Blue

Red

Blue

VM board

VM board

R B

R B

TLH

TLV

YCH

XCV

B

R

R

B

DY pocket

(XCV)

DY pocket

TLH Plate

YCH

TLV

(XCV)

If you are unable to adjust the corner convergence
properly, this can be corrected with the use Permaloy
Assy Correction.

1. Affix the  Permaloy Assy Correction corresponding to the

misconverged areas.

TLV

Rotate TLV-2 VOL (29", 34") on DY

XCV

Rotate XCV

Adj core on DY

YCH

Rotate YCH

VOL on DY

TLH

Insert

TLH

Correction Plate to DY Pocket

(Left or Right)

b

a

c

d

a-d : screen-corner
        misconvergence

a

b

c

d

a to d : Permaloy Assy Correction 

Fix a Permaloy Assy Correction 
to the misconverged areas 

– 12 –

1. Set the  PICTURE to Normal.
2. Go to Service mode. Set WHBL 016 RGBB lat to 01.
3.  Connect R,G,B of the  C board cathode to the

oscilloscope.

4. Adjust cathode voltage to the value below.
5. Adjust G2 (screen) on the FBT until picture shows the

point before cut off.

Cathode setting voltage:
170 V 

± 2 (VDC)

FOCUS adjustment should be completed before W/B
adjustment.

1. Receive digital monoscope pattern.
2. Set "Picture Mode" to "DYNAMIC". (Multi), Set "Picture

Mode to Vivid (NTSC).

3. a) Adjust focus VR so that the center of screen

becomes just focus (except 25").

b) Adjust focus VR so that the lion teeth

becomes just focus (25").

4. Change the receiving signal to white pattern and blue

back.

5. Confirm Magenta ring is not noticeable. In case

magenta ring is obvious, adjust FOCUS VR to balance
between MAGENTA RING and FOCUS.

1. Set to Service Mode (Refer Section 3-1:

ADJUSTMENTS WITH COMMANDER).

2. Input white raster signal.
3. Set Picture to DYNAMIC. Intelligent Picture: ON.

i. For SA & SR set OPTB 006 OPB 6 to 00.

4. Select WHBL 002"RDRV" and adjust the value to 37
5. Select WHBL 003"GDRV" and 004 "BDRV"and adjust

the data for the best white balance in highlight condition.

6. Adjust WHBL 000 "BKOR" and 001 "BKOG"and adjust

the data for best white balance cut-off condition.

7. Write into the memory by pressing [MUTING] then 

-

.

8. Write offset data for other mode.

After adjustment, please reset:
i. OPTM 006 – OPB 6 to original data (SA & SR series).

Adjust

Offset

Offset

18000

t 12363 t 9300

BKOR

–2

–3

BKOG

+1

+2

RDRV

0

0

GDRV

–3

–8

BDRV

–8

–18

1. Set to service mode.
2. Brightness set to 50%, Picture: Minimum.
3. Select WHBL 010 SBRT with 

1

 and 

4

, and adjust

'SBRT' data with 

3

 and 

6

 so that the third stripe from

right dimly lit.

4. Copy the adjusted data "WHBL" 010 SBRT in RF to

Video Mode.

5. Write into the memory by pressing [MUTING] then 

-

.

6. Models cut-off: 10 IRE

Slightly Glimmer: 20 IRE + 2 steps

Focus

Screen

– 13 –

Service adjustments to this model can be performed using the supplied remote commander RM-W109.

With the unit on standby

This operation sequence puts the unit into service mode.
This screen display is:

Set the standby condition (Press [POWER] button on the commander), then press [POWER] button again, hereupon it
becomes TV mode.

1. Set to Service Mode.
2. Press 

1

 (UP) and 

4

 (DOWN), to select the adjustment item.

3. Change item by pressing 

3

, 

6

.

4. Press [MUTING] button to indicate WRITE on the screen.
5. Press 

-

 button to write into memory.

1. After adjustment, pull out the plug from AC outlet, and then plug into AC outlet again.
2. Turn the power switch ON and set to Service Mode.
3. Call the adjusted items again to confirm adjustments were made.

  

t [DISPLAY] t 5 t [VOL $+% ] t [POWER]

Item no.

Service data

NVM

Service

Field

Channel no./

Category

in decimal

Item name

in decimal

NG

Command

Frequency

Video Input Name

GEOM

006

EWPW

031

x

SERVICE

60

S VIDEO 1

Software

Service data

Reserved

Power On Time

Release ID

Version

in binary

for factory

Color System

(decimal)

SUS01

3.50M

0001 1111

FF FF

NTSC3

65553

Status SID,
Lock, SL
:not locked
(no signal)

Status

Status BC,

Status

Status S/N

Status

Status Display

:locked

VW, IVWF

HBC

BCF

LEVEL (0-7)

GL

Area

111

11

11

1

7

11

ZZ xy 1 1 000000 000000

Status

PTW

S

: for Sony

A

: for AIWA

L

: BX1L Full

B

: BX1L Basic

D

: DVD Combo

U S : Taiwan/Korea/Philippines
G A : General Area
01 : Serial no. of the M / P release for each destination

1, 4

Select the adjustment item.

r

3, 6

Raise/lower the data value.

r

[MUTING]

Writes.

r

-

Executes the writing.

ZZ : DCXO Flash Value
xy : Value of x

:

Value of y

0 - unknown

0 - Mono

1 - BTSC

1 - Stereo

2 - A2

2 - Bilingual

3 - NICAM

4 - SAP/Single

4 - KOREAN
5 - Japan
6 - AV Stereo

– 14 –

7, -

All the data becomes the values in memory.

8, -

All user control goes to the standard state.

[Display], -

Service data initialization (Be sure not to use usually.)

2, 5

Select Device or Category (Up, Down)

Item Number 000 HPOS
This explanation uses H POSITION as an example.
1. Select "000 HPOS" with the 

1

 and 

4

 buttons, or 

2

 and 

5

.

2. Raise/lower the data with the 

3

 and 

6

 buttons.

3. Select the optimum state. (The standard is IF for PAL reception.)
4. Write with the [MUTING] button. (The display changes to WRITE.)
5. Execute the writing with the 

-

 button. (The WRITE display will be changed to red color while excuting, and back to

SERVICE.)

Example on screen display :-

Use the same method for all Items. Use 

1

 and 

4

 to select the adjustment item, use 

3

 and 

6

 to adjust, write with

[MUTING], then execute the write with 

-

.

Note : 1. In [WRITE], the data for all items are written into memory together.

2. For adjustment items that have different standard data between 50Hz or 60Hz, be sure to use the respective

input signal after adjustment.

031

1111

50

NTSC3 65553

EWPW

0001

GEOM

SUS01

006

3.50M

FF FF

SERVICE

031

1111

50

NTSC3 65553

EWPW

0001

GEOM

SUS01

006

3.50M

FF FF

WRITE

031

1111

50

NTSC3 65553

EWPW

0001

GEOM

SUS01

006

3.50M

FF FF

WRITE

GREEN

GREEN

Write with 

[MUTING]

Write executed with 

RED
The WRITE display
then the display
returns to green
SERVICE.

Adjusted with 

3 

and 

6 buttons.