DOWNLOAD Sony KV-SK29M80 Service Manual ↓ Size: 6.64 MB | Pages: 88 in PDF or view online for FREE

– 8 –

 

 

 

 

CN003

CV 

 

Dress Conn Assy, 5P YUV around shield case.
Use pin, wires A019 and A017 to dress Conn Assy, 
5P YUV as shown

Dress Conn Assy, 4P VM behind Conn Assy, 5P Front 
In as shown. Conn Assy, 5P Front In is used to prevent 
Conn Assy, 4P VM from bending towards T504, R579 
and R5032 (high temperature parts).

i) Earth Assy, Coating is installed as shown in 
  Figures (a) and (b).

ii) Insert the 2 Earth Assy, Coating wires to CN705 
  & CN707 as shown.
iii) Insert Conn Assy, 7P RGB into CN701.

Pin, wire A019

Make sure the UL tape is

positioned at

the sharp edge of shield case to

prevent wire from being scratched case

CN007

CN9201

CN905

Dress Conn Assy, 5P

YUV around shield

Keep wires

away

Pin, wire A017

Conn Assy, 5P YUV

Right side

Figure (a)

Figure (b)

Left side

CN701

Heatsink A751

Conn Assy, 7P RGB

Dress Conn Assy,

4P VM behind

conn Assy 5P Front In

Lead Assy, Earth is

above Conn Assy, 5P

Conn Assy,
5P Front In

Deflection area

T504

R503

R579

Conn Assy, 4P

CN9201

CAUTION:
Keep Conn Assy, 5P Front In away from deflection
area (T504, R5032, etc.) when dressing.

CN707

CN705

Earth Assy,

Coating wires

– 9 –

2-9.  Dress Lead Assy, Earth and Conn Assy, 5P Front In with purse lock Ø 5

 

CRT neck

CRT

 

 

 

 

 

  

Insert Lead Assy, H Static into CRT socket and RV750 
as shown. Make sure the wire is naturally curved, to 
avoid touching CRT neck.

Make a 'S' shaped loop on Conn Assy, 5P Front In as 
shown. Keep wires away from heatsink A010.

Lead Assy, H Static

Lead Assy, Earth

Conn

Assy, 5P

Lead Assy,

Speaker

Heatsink

Lead Assy,

Lead Assy, Speaker is not dressed together

with purse lock. Keep Lead Assy, Speaker

away from heatsink A010 by
dressing it close to the CRT.

Conn Assy, 5P Front

Heatsink A010

Lead Assy, Earth

Conn Assy, 5P

Note: Dress while chassis is halfway docked into beznet.

Make a 'S' shaped loop on Conn Assy,

5P Front In and dress together with

Lead Assy, Earth using purse lock Ø 5.

CAUTION:
Prevent tie, cable from touching rear cover or any enclosures by
turning them away from it
--> avoid rattle sound. Also prevent tie, cable's end from touching
solder side of board.

RV750

Purse lock Ø

 5

– 10 –

  

 

 

 

  

1) Dress Conn Assy, 6P and Conn Assy, 4P VM using
tie, cable at alignment hole 'B' on CV board as shown.
2) Dress Conn Assy, 4P 200V; Conn Assy, 6P;
Conn Assy, 4P VM; Lead Assy, G2 and Lead Assy, Focus
with purse lock Ø 5.

Dress Conn Assy, 7P RGB; Conn Assy, 5P Front In and
Lead Assy, Earth using purse lock Ø 9.
KeeP wires away heatsinks and high-temperature parts.

Purse lock

Conn Assy, 7P RGB

Lead Assy, Earth

is behind Conn Assy,

7P RGB

Conn Assy, 6P

Tie, cable at alignment hole 'B'

Conn Assy, 4P VM

Conn Assy, 4P 200V

Lead Assy,

G2

Pin, wire A707

Conn 

Assy

, 4P

 VM

Conn 

Assy

, 4P

 200V

Conn Assy

, 

6P

Lead Assy

,Focus

Lead Assy

, 

G2

Lead Assy,

Focus

Purse lock 

Ø

Conn Assy, 7P RGB

Lead Assy, Earth

Conn Assy, 5P

Purse lock 

Ø

 5 

Purse lock 

Ø

 9

Prevent tie, cable from touching rear cover or any
enclosures by turning them away from it
--> avoid rattle sound. Also prevent tie, cable's end from
touching solder side of board.

Conn Assy, 5P Front In

CN004

Make loop of Conn Assy, 7P RGB as

large as possible when dressing with purse lock

Keep Conn Assy, 5P Front In

wire in an upward path from

CN9201 to where it is dressed

with purse lock 

Ø

 9. This is to

keep it away from deflection area.

Lead Assy, Earth

– 11 –

 

 

 

  

 

 

 

 

DY

Install Rotation Coil as shown.
1) Coil positioned in clockwise direction.
2) Wire is at 3 o'clock position.

Avoid any stress on Lead Assy, G2; Lead Assy, Focus
and terminal at W7001.

Dress DY Connector; Conn Assy, 4P 200V; Conn Assy 4P 
VM and Conn Assy, 6P using purse lock Ø 5 as shown.

Dress DY Connector;
Conn Assy, 4P VM and
Conn Assy, 6P using
purse lock Ø 5 as shown

Conn Assy, 4P VM

CN180

A715

W7001

Lead Assy, G2

Lead Assy,

Focus

Purse lock Ø 5

Wire from Rotation

Earth Assy,

Coating wires

Rotation coil conn is dressed outside

and below Earth Assy, Coating wires

A713

Rotation Coil Conn

DY Conn

Dress purse lock Ø 5 by

using height of heatsink

as a guide

Conn Assy,

4P 200V

Use height of

heatsink as a guide

Conn Assy

, 

4P

VM

DY

 Connector

Conn Assy

, 

4P

 

200V

Conn Assy

, 

6P

Keep Conn Assy,

4P 200V away from FBT

(min. 10mm)

Note: Make sure DY connector is inserted securely.
--> prevent it from coming out.

Conn Assy, 6P

Keep wire away

from R781 and

heatsinks

A713, A715.

Dress Rotation Coil

connector together with

Lead Assy, G2; Lead

Assy Focus and Conn

Assy, 4P 200V using

pin wire A707

Conn Assy, 4P 200V

Keep wire away

from R781

Prevent wires from touching
rear cover or any enclosures
by turning them away
from it --> avoid rattle sound.

Prevent wires from touching rear cover or any
enclosures by turning them away
from it --> avoid rattle sound.