DOWNLOAD Sony KV-AR292M50 Service Manual ↓ Size: 13.44 MB | Pages: 127 in PDF or view online for FREE

23

Additional Information

1

2

3

R

L

Y

C

B

C

R

x

Connecting to the video input terminal ( t )

4

L(MONO)

1

2

3

R

L

Y

C

B

C

R

R

Notes
• If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the

program number 0 on the TV (see page 21).

• When both 

 (S video) and 

 (video) for t 1 or t 4 are connected at the same time, 

(S video) is automatically selected. To view 

 (video), disconnect the S video cable.

Connecting to the monitor output terminal ( T )

24

Additional Information

1

2

3

R

L

Y

C

B

C

R

 

Notes
• If your DVD player can output interlace and progressive mode signals, select the interlace

output when connecting to 

 (component video input) on your TV. Your TV can receive

either 525i/60Hz or 625i/50Hz interlace signals.

• Some DVD player terminals may be labeled differently:

• If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks will not

be output properly. This does not indicate a malfunction.

Y (green)

Y

C

B

 (blue)

C

B

, P

B

, C

b

 or B-Y

C

R

 (red)

C

R

, P

R

, C

r

 or R-Y

25

Additional Information

23

–

21

–

–

21

• Check the antenna cable and connection

on the TV, VCR and at the wall.

• Check the antenna setup.

Contact a Sony dealer for advice.

• Display the “Channel Setup” menu and

select “Manual Program” to preset the
channel again.

• Try using a booster.

• Turn off or disconnect the booster if it is in

use.

• Display the “Channel Setup” menu and

select the appropriate “TV System”.

• The connection is loose

or the cable is
damaged.

• The antenna setup is

inappropriate.

• Channel presetting is

inappropriate or
incomplete.

• Signal transmission is

low.

• Broadcast signals are

too strong.

• The TV system setting

is inappropriate.

x

If you find any problem while viewing your TV, you can either use the Reset
function or check the Troubleshooting guide below. If the problem persists,
contact your Sony dealer.

Press the RESET button on your remote control.
Your TV will go blank for a few seconds
then the “Initial Setup” menu will appear.

Pressing RESET will set your TV to the factory
setting, but certain problems may be solved.

7

8

9

0

26

Additional Information

• The power cord,

antenna or VCR is not
connected.

• The TV is not turned

on.

• The volume level is too

low.

• The sound is muted.

• There is local

interference from cars,
neon signs, hair dryers,
power generators, etc.

• Broadcast signals are

reflected by nearby
mountains or
buildings.

• The antenna setup is

inappropriate.

• Use of a booster is

inappropriate.

• The color level setting

is too low.

• The color system

setting is
inappropriate.

• The antenna setup is

inappropriate.

• Check the power cord, antenna and VCR

connections.

• Press 

 ?/1

 (power).

• Press ! (main power) on the TV to turn

off the TV for about five seconds, then
turn it on again.

• Press 2 + to increase the volume level.

• Press 

 to cancel the muting.

• Do not use a hair dryer or other

equipment near the TV.

• Check the antenna setup. Contact a Sony

dealer for advice.

• Use a highly directional antenna.

• Use the fine tuning (“Fine”) function.

• Check the antenna setup. Contact a Sony

dealer for advice.

• Turn off or disconnect the booster if it is in

use.

• Display the “Picture” menu and select

“Personal” of “Mode”, then adjust the
“Color” level in “Picture Adjustment”.

• Display the “Setup” menu and check the

“Color System” setting (usually set this to
“Auto”).

• Check the antenna setup. Contact a Sony

dealer for advice.

23

9

8

10

9

–

–

–

21

–

–

16

22

–