DOWNLOAD Sony KP-48S65R Service Manual ↓ Size: 7.95 MB | Pages: 80 in PDF or view online for FREE

– 37 –

1. Adjust with GH MSIZE so that the sizes of both ends and of

both sides of the center section of the screen are equal.

2. Adjust with GH SIZE so that the horizontal sizes of both

ends and of both sides of the center section of the screen are
equal.

3. While tracking, adjust with GH MSIZ and GH SIZE so that

the lattice intervals for the horizontal line section of the cen-
ter section of the screen are equal and so that the horizontal
size is the prescribed value.

4. If M LIN is changed when the GH MSIZ and GH SIZE ad-

justment is complete, adjust again while tracking.

•

 With just the H SIZE adjustment in MAIN, if there is no need

to adjust GH SIZE in SUB this can save power.

1. Adjust with GV MSIZE so that the sizes for the top and bot-

tom sections of the screen and for both sides of the center
section of the screen are equal.

2. Set the vertical size to the prescribed value with GV SIZE.
3. Adjust GV MSIZ and GV SIZE watching the vertical line at

the center section of the screen.

4. While tracking, adjust with GV MSIZ and GV SIZE so that

the lattice intervals for the vertical line section of the center
section of the screen are equal and so that the vertical size is
the regulation value.

5. If GV LIN is out of place when the GV MSIZ and GV SIZE

adjustment is complete, adjust again while tracking.

•

If there is no need to adjust GV SIZE in SUB with just the V
SIZE adjustment in MAIN, this can save power.

MSIZ

SIZE

GH MLIN

GH MSIZ

GH LIN

GH SIZE

1. Adjust GV LIN so that the vertical lines at the top and bot-

tom of the screen are symmetrical.

MSIZ

SIZE

GV LIN

GV SIZE

GV MSIZ

1. Adjust with GH SSKW so that the tilt of the vertical lines at

both ends of the screen is symmetrical left and right.

2. Adjust with GH KEY so that there is no tilt in the vertical

lines at both ends of the screen.

3. If there is a tilt on either the left or right after the GH KEY

adjustment, adjust while tracking.

SS KW

KEY

– 38 –

1. Correct the quaternary distortion with GH 4PIN.
2. While balancing, correct the quaternary distortion of both

end sections of the screen with GH 4SBOW.

3. While tracking, adjust with GH 4PIN and GH 4SBOW.

4 PIN

4SBO

4SBOW

1. Adjust with GH MBOW so that the pin asymmetry at both

sides of the center section of screen is symmetrical.

2. Adjust with GH SBOW so that the bow at both end sections

of the screen is symmetrical left and right.

3. While tracking, adjust with GH MBOW and GH SBOW so

that the bow of vertical lines on the entire screen is sym-
metrical left and right.

M BOW

S BOW

1. Adjust the pin distortion at both sides of the center section of

the screen with GH MPIN.

2. Adjust the pin distortion at both end sections of the screen

with GH PIN.

3. While tracking, adjust with GH MPIN and GH PIN so that

the PIN of vertical lines on the entire screen have no bowing.

4. If there is asymmetrical pin distortion after the GH MPIN

and GH PIN adjustments, adjust with GH MBOW and GH
SBOW while tracking.

•

 With just the PIN AMP adjustment in MAIN, if there is no

need to adjust GV PIN in SUB, this can save power.

M PIN

PIN

GH MBOW

GH PIN

GH SBOW

GH MPIN

1. Take the screen top and bottom horizontal lines with GV

WAVE and find the secondary and quaternary waveform.

2. There is KEY distortion after the GV WAVE adjustment, so

adjust with GV WAVE and GV KEY while tracking.

GH MBOW

GH MPIN

GV WAVE

GV KEY

– 39 –

1. Correct the quaternary distortion of the horizontal lines at

the top and bottom sections of the screen with GV 4PIN.

1) Since there is no 4SBOW for vertical correction, there will

be a slight imbalance, but adjust to eliminate the distortion
from the horizontal line at either the top or the bottom of the
screen.

2) In many cases, the horizontal lines at the top and bottom sec-

tions of the screen are not straight lines after the adjustment.
As long as the secondary distortion is mild enough that it can
be corrected with the PIN adjustment, this is OK.

GV 4PIN

1. Adjust with GV SSKW so that the tilt of the horizontal lines

at the top and bottom sections of the screen is symmetrical
about the center position horizontal line.

2. Adjust with GV MKEY so that there is no tilt for the line

sections at both sides of the horizontal lines at the center sec-
tion of the stream.

3. Adjust with GV KEY so that there is no tilt for the horizontal

lines at the top and bottom sections of the screen.

4. While tracking, adjust with GV MKEY and GV KEY so that

there is no tilt for the horizontal lines on the entire screen.

5. If the tilt is unbalanced after the GV MKEY and GV KEY

adjustment, adjust again with GV SSKW.

GV SSKW

GV KEY

GV MKEY

MKEY

KEY

GV SSKW

1. Correct the asymmetrical pin distortion at the top and bot-

tom sections of the screen with GV SBOW.

GV SBOW

1. Adjust the pin distortion for both side sections and the center

of the screen with GV MPIN.

2. Adjust with GV PIN so that the horizontal lines at the top

and bottom sections of the screen are straight lines.

3. Adjust with GV MPIN and GV PIN so that there is no curve

in the horizontal lines on the entire screen.

4. After the adjustments in Items 1-3, adjust the tracking with

GV SBOW, GV MPIN, and GV PIN.

GV SBOW

GV MPIN

GV PIN

MPIN

PIN

– 40 –

1. Receive a cross-hatch signal.
2. Adjust so that the red lines lay on the green lines.

Adjust with the same procedure as the GREEN SUB adjust-
ment.

Notes:

1. The main correction is not carried out during

 red registration adjustment.

2. Beware.  The green adjustment items can be

 changed by mistake.

3. Unlike for green, adjust within the range -127

 ~ +128.

1. Receive a cross-hatch signal.
2. Adjust so that the blue and green lines are on top of each

other.

Notes :

1. The main correction is not carried out during

RED registration adjustment.

2. Beware. The GREEN and RED adjustment

items can be changed by mistake.

1. Receive an off-air signal.
2. Adjust the AGC VR ( TU 1001 ) so that there is no snow

noise and cross-modulation.

1. Receive the monoscope pattern signal and adjust the picture

quality with the menu.

2. Adjust service mode SBRT so that the signal 10 IRE section

barely glows.

3. Receive the all-white pattern signal.
4. Adjust the white balance with service mode GCUT and

BCUT.

5. Adjust service mode SBRT so that the signal 100 IRE sec-

tion barely glows.

6. Adjust the white balance with service mode GAMP and

BAMP.

7. Repeatedly adjust the white balance for the minimum and

maximum picture settings.